Question about 2002 Jaguar X-Type

1 Answer

02 jag x type turns over gets gas has spark turns over starts to hit but want tried starting fluid where to go from here new battery new plugs new alternator timing chain not broke

All fuses and relays good any solutions

Posted by on

  • Justin
    Justin Mar 22, 2014

    Yes and the motor is turning but want start

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Jaguar Expert
  • 196 Answers

Ok have you checked the cam postion sensor signals?if they are good, next check the inertia switch on the passensger side kickpanel and make sure the switch is deactivated that cuts fuel off to the engine,if the pump is working and all fuses good, then make sure the center security light is not on solid after the inition is turned on to phase two.If this light stays on then its a security issue whereas the inition isnt recognizing the key,If all this works,then go under the hood,disconnect the coolant temp sensor on the passenger side of the engine ,its a19 mm socket,to remove but just disconnect the sensor connector then try and crank it...These will make the s type not run at all...This is a step by step troubleshoot for these cars that I have ran into

Posted on Apr 14, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
countrysi248
  • 443 Answers

SOURCE: How to pull codes from a Jaguar X Type 2.5 2003

something wrong here .. battery tests good and starter tests good and it wont spin the engine over. ok what if you jump start it ? if it spins the engine the battery is shot.. if the starter is spinning and not turning the engine the starter or selonoid is bad .. thats got to be all there is to it .. thanks again Jerry

Posted on Feb 09, 2009

  • 21 Answers

SOURCE: '02 Jag belt or chain?

It has a timing chain.

Posted on Mar 20, 2009

carlsbiz
  • 1124 Answers

SOURCE: Acceleration slow or choppy

A tune up is a good idea.. Also depends when the last tune up was..
And yes - spark plugs are included in a tune up..

Note;
Thank you for posting your question on FixYa.com
We are helping people on a points system.
If the information provided here was at all helpful,
please be kind - rate well and close the post.
Thank you – and enjoy your day ;o)

Posted on Aug 06, 2009

Testimonial: "Got spark plugs changed and hesitation has stopped. Thank you."

SOURCE: key fob 2001 jag s-type stopped working. not battery

Your car has a module for the FOB , that could need to be replaced and programmed , or just to reprogram keys again

Posted on Aug 13, 2009

raygin
  • 322 Answers

SOURCE: 200 jag stype no start anti-theft light flashing

Have you another key and fob ?

Try lock/unlock cycle with new key + fob. Your key may be corrupted.

Try also just unlocking the car with the key (not the fob) as soon as you unlock the door put the key in the ignition immediately and see if the car starts.

If you have your radio code it may be worth trying a total reset (leave the car unlocked) disconnect the battery and leave for 20 mins. then reconnect, most systems will then reboot and this MAY help?
Failing all the above it looks like dealer time - more ££ss

good luck !

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would suzuki forenza stall at a stop


Turn the ignition and start the Suzuki Eiger. If the engine has difficulty starting or will not start at all, there may be a problem in the electrical or starting system. Remove the spark plug wire from the spark plug and remove the spark plug from the engine using a spark plug wrench. You can replace the spark plug or use a wire brush and gap tool to clean and re-gap the spark plug. Insert and tighten the spark plug, reattach the spark plug wire and try to restart the engine. Remove the battery cables from the battery and attach a battery meter to the battery. Observe the amount of charge the battery is holding and if the meter has a test feature, test the battery to see if it will dispense the correct amount of power. Clean the battery contacts with a wire brush and reconnect the battery cables. Check the oil, gas, transmission and brake fluid levels on the Suzuki Eiger. If there is not enough gas in the ATV, it will not start. Checking the fluids regularly to see if there are any leaks or if any of the fluids are dangerously low. Top up any fluids that may be low before you use the ATV. Adjust the fuel idle mixture screw on the Suzuki Eiger's carburetor if the engine is running rough. Inspect the air intake and exhaust pipe for the Suzuki Eiger. Any blockage in or on these components can affect engine performance. OBD2 PROMOTION FindOBD2 com

Aug 15, 2014 | Cars & Trucks

1 Answer

Spec vin ecu specs


If it turns, then the battery is OK. Either spark plugs are not firing in proper order (wrong firing order), no power to spark plugs, or no fuel because of fuel restrictions (dirty fuel filter). Inspect the air filter to ascertain its not clogged air. If you smell gas, then you saturated the spark plugs, which is why it refuses to run.
Let it sit for half hour to let spark plugs dry. Inspect to ascertain its not dirty spark plugs, which will also prevent engine from running. After ascertaining its proper firing order, spark plugs are clean, and there's power to distributor cap, ascertain there's fuel in fuel lines by squirting half second (short squirt) of starting fluid into air filter. Close the air filter housing to trap flammable starting fluid gas. Turn engine without giving throttle. Let starting fluid be ignited by spark plugs. If it won't start, then spark plugs are not firing to ignite starting fluid gas. If it starts briefly, but won't run when you give throttle, but catches when a 2nd person squirts more starting fluid into air filter just before engine stalls, then its a fuel restriction issue or no fuel in fuel lines.

Nov 29, 2013 | Cars & Trucks

1 Answer

1992 gmc jimmy wont start unless i spray with starting fluid after it starts it will start every time untill the next day then i have to spray again ?


Fuel pump issue.--

Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.


To confirm the problem, the basic troubleshooting is required.


Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.
Thanks.

Feb 13, 2012 | 1992 GMC Jimmy

1 Answer

Car turns over but won't start.


Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.


To confirm the problem, the basic troubleshooting is required.


Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.

Thanks.

Feb 07, 2012 | 1999 Lincoln Town Car

1 Answer

My mountaineer won't start. It sat for a little over a year because of transmission issues. When I finally got a trans for it, it wouldn't start. I replaced all spark plugs and replaced the...


If the engine is turning, but slow, she may need the battery terminals cleaned, if it has sat for over a year, yes, it may need a new battery. If the engine is turning over and she is not cranking up. Standard rules apply... does she have fuel? does she have spark, does she have compression? First thing is easy, get a can of starting fluid and give her a spray in the air filter area during cranking, if she pops off you have spark, which means no fuel. If it does not try to hit, that means no spark and more trouble shooting will need to be done. If it starts on starting fluid, you may have a bad fuel pump. AS gas turns to gunk as it dries up. And that may have gummed up the pump and filter. Hope this helps FixYa up.

Sep 12, 2011 | 2003 Mercury Mountaineer

3 Answers

I'm helping a friend to get his 02 Ford Explorer going after sitting for about 6 months, put in new battery and checked fluids then tried starting. it would crank over but not fire up,tried numerous times...


You need fuel, air, and spark to start it. Make sure the engine is getting fuel. Make sure the pump is working. Fuel goes from the pump to the filter, through the lines, to the engine. If the engine is getting gas, you need to check for spark. This concerns the spark plugs/coils, wires, distributor, coil pack, dist.cap, rotor, cam sensor, crank sensor, timing belt, ecm. It is a lot of things but anyone of them can make the car not start. That is why it is important to do a fuel check and a spark check. If it gets fuel, that cancels out fuel. Same for the ignition system, where you get the spark. If you have any questions, just let me know.

Mar 06, 2011 | 2002 Ford Explorer

1 Answer

The engine cranks but it won't start


spray starter fluid in the intake and try to start .if engine hits like it is trying to start then ing is good. check the gas if you have gas then it might be a bad fuel pump.

Jan 05, 2010 | 1989 Isuzu Pickup 2WD

4 Answers

78 corvette that has not been started in 3


1.) put aside about $50 that you are ging to spend... period
2.) drain the oil and remove the old oil filter
3.) install a new oil filter, add new 30W oil
4.) remove all 8 spark plug wire from the 8 spark plugs
5.) remove the 8 spark plugs
6.) spray about 5 seconds of WD40 into each of 8 spark plug holes
7.) spray the remainder of the can into each of the 2 valve covers thru the EGR holes (pull out the EGR valve first)
8.) making certain that you have a full battery charge, turn the starter switch to START for about 5 seconds... if your engine turns then your internals are not frozen... that's good
9.) open another can of WD40 and spray equal amounts into ecah of 8 spark plug holes a second time
10.) turn the start switch on for another 5 seconds and listen for strange sounds... by the way without the spark plugs the engine will rotate more quickly than you normally expect... not a problem because as it turns it is lubricating your internal parts
11.) wait a minute and then turn it on for for about 10-20 seconds while listening for scraping or knocking sounds... if none heard then you are all lubed up and ready to reinstall the spark plugs.
Install new plugs or sandpaper the old with the correct gap ( I believe .035")
12.) if you didn't mark the plug wires not a problem... Google '78 Chevy Distributor Firing Order to find terminal #1 on the distributor cap... usually about the 1 o'clock position
13.) install #1 wire to #1 sparkplug... the driver's side front closest to the radiator
14.) the distributor rotates like a clock (clockwise) and the numbers on the clock starting at #1 is 1-8-4-3-6-5-7-2.... this is the firing order in a clockwise direction
15.) take the next plug wire #8 and connect it to #8 spark plug
Note: the spark plug numbers are cast into the top of the intake manifold for easier identification
16.) conect the remaining wires to their respective plugs
17.) make certain that you have a full battery charge, some gas in the tank (gas evaporates over 3 years) and a full radiator.
18.) Turn the starter switch and listen for the engine to start
19.) If it doesn't start the first time, try again and wait for the gas to reach the carburetor.... try again
20.) if it still doesn't start spray some engine strating fluid into the carbuetor throat and try again... it should start
21.) if it starts but doesn't keep running then repeat step 20. unitl the gas reaches the carburetor and continues to run on its own...!

Jun 23, 2009 | 1994 Chevrolet Corvette

2 Answers

1989 pontiac sunbird will not start


you probably have water in the gas.you will have to add "heet"to the gas and maybe even remove the air intake tube and try to start it using starting fluid.

Dec 26, 2008 | 1989 Pontiac Sunbird

Not finding what you are looking for?
2002 Jaguar X-Type Logo

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...