Question about 1993 Lexus Ls 400

1 Answer

Electronic The gear won't engage and the lights inside are not coming on.due to battery post put on the wrong ends and something pop

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 148 Answers

Try checking the fuses on your system.

Posted on Mar 22, 2014


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was stopped at a stop sign and when i accelerated my car started moving then made a popping noise and stopped moving. Now it will only move in reverse and first gear. What is wrong with it?


Sounds like a similar problem that I had. I bet the check engine light is on. If so have vehicle scanned for codes. You most likely popped something in transmission.

Jul 29, 2016 | Cars & Trucks

1 Answer

Put wrong key in ignition.


Please don't overlook the importance of a good battery with clean/tight post connections...try disconnecting both + and - clean terminals and cables and reconnect...the brain should also re-set...Hope this helps.

Oct 29, 2015 | 2001 Jeep Grand Cherokee

1 Answer

I put my truck in 4 wheel drive and went to go made a pop and not it wont go into 4 wheel drive the light lights up but wont engage the 4 wheel drive


Based on the info posted, I believe you may of experienced a shift fork tab failure inside the transfer case and the gears that are moved by the shift fork no longer can be moved correct because the tab on the shift fork is either broken or worn down.

Feb 14, 2014 | 1999 Ford F150 Regular Cab

1 Answer

2005 chevy silverado 2500 HD starter won't engage


The pinion gear could be jammed in the ring gear but if you have considerable mileage on the starter and everything else checks good you could be due for a starter replacement

Feb 25, 2013 | Chevrolet Silverado 2500HD Cars & Trucks

2 Answers

No power any were no inside lights, no dash lights, no ingition lights when key is turned, Engine won't turn over. Battery is good, Before reaching this condition was running very ruff. I heard a pop...


i would check out the positive battery cable that runs to the starter, also , check all of the wires that are at the starter , to make sure that they are not loose, torn, burnt, ot frayed.

Jun 24, 2011 | 1998 GMC Safari

2 Answers

My car is not ingaging to turn over


If it is just clicking, then the battery is too weak. Charge the battery or jumpstart.

If the battery is full charged and when you turn the key, the starter is just clicking again, possibly bad starter or bad battery cable ground. Check your grounds from the battery.

If it is a new starter and it is clicking like it won't engage, then it is not shimmed properly.

If you figure out what is wrong and need further help, please reply to this post with your questions.

Thanks! Oh, please post your engine size, year of car or truck and model. This helps A LOT!!!

Apr 19, 2011 | Dodge Neon Cars & Trucks

1 Answer

I have a 1989 F-150 with a hidden electical short. The battry is drained if I leave it connected for 2 days or more and don't drive the truck. I found a similar question here, the response was to...


HERE IS HOW TO CHECK FOR A BATTERY DRAIN. TURN OFF ALL SWITCHES, MAKE SURE THE GLOVE COMPARTMENT IS CLOSED & THAT THE LITE INSIDE IS GOING OUT .RAISE THE HOOD, DISABLE THE UNDER HOOD LIGHT. CLOSE ALL THE DOORS TIGHT. MAKE SURE ALL COURTESY LIGHTS ARE GOING OUT. GET A 12 VOLT CIRCUIT TESTER, { A SEE THROUGH ICEPICK WITH A LIGHT INSIDE }. REMOVE THE NEG BATTERY CABLE, PUT ONE END OF THE TESTER ON THE NEG BATTERY POST. PUT THE OTHER END OF THE TESTER ON A GOOD GROUND. IF THE TEST LIGHT LIGHTS UP THAT SAYS THERE IS A BATTERY DRAIN. IF THE LIGHT IS ON. START PULLING FUSES ONE AT A TIME FROM THE FUSE/ RELAY BOX NEAR THE BATTERY. WHEN THE LIGHT GOES OUT THAT IS THE DRAINING CIRCUIT. YOU MAY WANT TO DISCONNECT THE ALTERNATOR. ALTERNATORS CAN CHARGE THE BATTERY WHEN THE MOTOR IS RUNNING & IF SOMETHING IS WRONG INSIDE THEY CAN DRAIN THE BATTERY WHEN STOPPED OVERNIGHT.

Jan 09, 2011 | 1989 Ford F 150

1 Answer

2000 mitsubishi Diamante,one week after a new axle was installed,the first thing to happen was...When the car was started and after warm-up,once put into Drive,gear indicator light on the dashboard would...


By the sound of your problem your vehicle has an electronic automatic gear box but correct me if I am wrong..Now this can be caused due to a faulty electronic part but I cannot guarantee this.It may need a diagnostic tool hook up to the car to read the error code.(if it's giving a check engine light )

Nov 12, 2009 | 2000 Mitsubishi Diamante

2 Answers

Two days ago I noticed my battery was flat as I left the lights on. I recharged it last night and put it back in again today. I then pressed the lock button on my keyfob 5 times so that the key is...


That clicking is the starter trying to engage. Try jumpstarting the vehicle. Your battery may not have come back yet.... and you may need a new one. Try letting it run for a half hour or so after jumpstarting. If it starts immediately after shutting it off you're probably good to go. If it requires another jumpstart then you need a new battery.

Nov 10, 2009 | Saab 9 3 Cars & Trucks

1 Answer

Manual transmission shifter will not engage


Sounds to me that the shifter broke, i believe the shifter has a ball end that slips into a pocket in trans. that moves for gear selection and that ball brook off end of shifter. if its got a linkage set up most likely samething either shifting arms came off or shifter broke where linkage rods connect.

Feb 12, 2009 | 1994 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...