Question about 2000 Chevrolet Venture

1 Answer

Windshield wipers do not park correctly

Wipers park in upright position. Other than that they work fine.

Posted by on

  • Miles Mar 22, 2014

    under hood on passenger side look for plastic cover on your wiper transmision , take it off and you will see a pin that should disengage. some grease on it and manually try disengaging it and it should work great. contact me again if you need more help

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 26 Answers

More than likely, your little wiper transmission isn't catching correctly. I had this issue with my sisters Buick. Open the hood. Remove the panel located nearest to the bottom of you windshield near your wipers. You should see a small oval or teardrop shaped cover, (approximately the size of a playing card) that you will need to remove to expose the wiper transmission. It just pops off. Turn your wipers on and see if the "tab" on the transmission catches to stop your wipers in the down position. Her's did not. I lubricated it slightly and with careful pressure, bent the tab just a bit. The wipers then caught at the appropriate time, closing the wipers correctly. Remember to replace the cover and the panel on your vehicle when complete. Ever onward! Hope this was helpful for your model as well.

Posted on Mar 23, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 90 Answers

SOURCE: 1999 Chevy Venture, Windshield wipers stop in upright position

You will need to replace the wiper transmission.This is a common problem.

Posted on Jan 24, 2009

  • 132 Answers

SOURCE: windshield wipers stuck upright when off

It is the fuse or the pulse board. Most likly the pulse board though

Posted on Jan 30, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2005 impala windshield wiper

the wirpers are connected to a shaft. the shaft is connected to a motor. The shaft must have turned and wipers were stuck and didn't move. So you will need to pull of each wiper arm and reposition with wipers turned off.

Posted on Apr 03, 2009

Tech jk
  • 102 Answers

SOURCE: windshield wipers stuck upright when off

This is a commoon problem with what is called the "Park pawl stop". The tab is most likely bent and needs to be re-aligned, then the wipers need to be re-timed. This re-timing can be a little difficult, although the re-aligning of the tab is failry simple.

TechJK

Posted on Apr 18, 2009

  • 129 Answers

SOURCE: wipers willnot return to park position

I've fixed this problem before. You have to disconnect the wiper transmission from the wiper motor. Put wipers in off position, unbolt the plate on top of wiper, turn wipers on then off. In the off position see where the wiper transmission is position in relation to where the park position is, remove the top plate from wiper motor and position it so as to be able to reconnect the wiper transmission now in the proper place. Please keep me informed. thanks you

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

2 Answers

Wiper timing switch


Susan, inside the wiper motor is a parking peg which controls the position of wiper blades when off, It is possible the peg is damaged or broken. The wiper motor would have to be replaced in this case. You can find a used one at the auto wreckers, just make sure the plug is the same as yours, as they may be different from one year to another.Have a good Tech. check wipers, diagnose and estimate repair.
Check the attached links,instruction and guides, 1 st link gives procedure to change wiper motor. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://boards.straightdope.com/sdmb/showthread.php?t=240691
Wipers will not park Body and Interior Crownvic net
2000 Ford Crown Victoria Windshield Wiper Issues Electrical

Aug 21, 2016 | 1999 Ford Crown Victoria

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

1 Answer

I have a '97 Z24 Cavalier that although the windshield wipers work, when turned off the go back to an upright position. When turned on any setting (whether fast or slow) they do stay down in the "resting"...


Sorry but your description doesn't really make sense - the wipers work, you say, but when switched on they remain in the correct parked position...
Presumably when switched off they park vertically.

It is worth noting the single sweep timer and the screenwash (5 wiper sweeps) influences the self parking. The circuit is quite complicated and it is best not to be involved unless necessary and then a circuit diagram would be invaluable.

It is also important the wiper linkage crank is correctly "timed" to the wiper motor for correct parking.

The wiper motor and integrated gearbox is fairly simple to examine and test but the gearbox also contains the self parking switch which can be examined for wear and cleanliness though testing isn't very practical.

I suggest you begin by removing the wiper motor and examining the condition of the self parking switch inside the gearbox. If it is worn or corroded replace the motor. When refitting connect the wiring and switch on the ignition and then briefly switch on the wiper motor and switch off. The motor should continue for a second or two and then stop.
Switch off the ignition.
Position the wiper blades in the proper parked position and then refit the wiper linkage crank to the motor...

Nov 05, 2017 | Chevrolet Cavalier Cars & Trucks

1 Answer

Rear windshield wiper problem on 99 Expedition.


2 ways of dealing with this. Install a new motor or put up with it until you install a new motor. I usually give it a very light tap with a hammer or a wrench & they start working fine at least for a while

Oct 15, 2009 | 1999 Ford Expedition

1 Answer

Windshield wipers stuck in upright position


You have a bad Park switch. Its located on the wiper motor. Replacing the wiper motor should solve the problem.

Apr 10, 2009 | 2002 Pontiac Grand Prix

1 Answer

Windshield wipers stuck upright when off


This is a commoon problem with what is called the "Park pawl stop". The tab is most likely bent and needs to be re-aligned, then the wipers need to be re-timed. This re-timing can be a little difficult, although the re-aligning of the tab is failry simple.

TechJK

Apr 02, 2009 | 2005 Chevrolet Monte Carlo

2 Answers

1990 Ford Taurus GL windshield wipers park in the wrong position


I have a 1996 Ford Taurus with a similar malfunction the intermittent wiper function is erratic, but the wipers park properly. I'm the original owner & this malfunction was in the car from the factory. I have a regular Ford Dealership manual & came to the conclusion that the Generic Electronic Module located behind the fuse panel is bad (computer glitch in programming) ! Ford Dealers want over $ 300.00 for a brand new module, I haven't checked with my local used auto parts recycler yet, but I know it will be less than the dealer price !

Mar 16, 2009 | 1990 Ford Taurus

1 Answer

1999 Chevy Venture, Windshield wipers stop in upright position


You will need to replace the wiper transmission.This is a common problem.

Jan 24, 2009 | 1999 Chevrolet Venture

Not finding what you are looking for?
2000 Chevrolet Venture Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...