Question about Jeep Cherokee

1 Answer

Quarter glass install

How do you put a quarter panel glass in?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

No year, no joy.
sorry.
here is FSM
look it up.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

my guess under body chapter
yup, i see it there under stationary glass.

Posted on Mar 22, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2003 volkswagen beetle covertible quarter panel removal

I do not recommend this job unless you are a seasoned mechanic, VW dealership charges $1000 for a reason. They almost earn it on this one. but heres how it's done or how I did it any way. the complete job took me 4 hours and I been at this for 30 years. But a lot of this time was figuring out how it came apart. First, drop the top, pull up on seat bottom and remove it, remove center panel, remove 3 allen bolts at bottom on seat back and remove. headrests, they just pull off, raise top just enough to make hinged panels flip up. remove nut at top rear corner of side panel. you can see the back side of the nut and bolt it is on from the panels that flip up. Remove Nylon push lock rivet where seat belt goes through panel on rear, top, corner. Pull out on panel to release it, there is 5 or 6 nylon locks that just pull out of holes in the body. It will sound like your breaking it when the locks pop loose, or mine did. then lift to gain access to remove seat belt bolts and unplug flip panel motors. remove cable end from its clip. Pull seat belts through panel. Set panel a side. remove torx head bolt around oval panel that speaker is mounted on. unplug speaker and regulator and pull wire harness thru hole. remove 2 allen and 5 hex bolts at top where window would come out if it worked. pull up on plate and move rubber window seal to the side to remove plate. remove 2 nuts at bottom of regulator and one about half way up towards front, lift regulator and window up through top to gain access to 3 nuts that hold window to regulator, from the top lift window out first then regulator. Reverse to assemble it.

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

How do you change a quarter panel window on a 2004 saturn vue


You need a professional glass shop to install this window.

Mar 11, 2016 | Saturn Cars & Trucks

1 Answer

How to replace a quarter window on 95' Ford thunderbird LX. Passenger side quarter window and what tools will I be using.


Remove the door panel, remove the window trim, remove the window regulator, Remove the window frame(push down ,then pull out from the top), Remove the broken glass from the seal, install window. Put back together in reverse order. You will need a Phillips screw driver, a drill and 1/4 bit, a 10 MM wrench or socket, 1/4 rivets X 1/2 inch long and rivet gun that handles up to 1/4 inch rivets.

May 03, 2015 | 1995 Ford Thunderbird

1 Answer

How to replace rear blower motor motor in 2006 chrysler town and country van


from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

1 Answer

R/H rear quarter window repalcement


tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.
  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

May 29, 2009 | 2004 Ford Focus

2 Answers

We need to install a new rear heater hose on our van and are not sure how too do it


I've done this many times
You will need a tubing cutter
Screwdriver
I think a 7 or 8mm socket
hose clamps
the appropriate amount of heater hose
zip ties

cut the steel heater line at the front in a place you can get access to,leave yourself enough steel hose on the rear to allow you to put the heater hose on cut off the steel hose and discard, and use 2 hose clamps on either end do the same for the other heater hose,this way is cheap and easy and permanant.Be sure that when you run the heater hose keep it away from hot or moving parts,use the zip ties to fasten it along the way,this should take about a half hour or so depending on your skills and working conditions,remember to buy some antifreeze to top up the system because you are going to spill some,remember to clean any spills animals love it and it is deadly.

Apr 16, 2009 | 2001 Chrysler Town & Country

1 Answer

Front quarter panel


"damn" didnt know you could spay a quarter panel lol

just kiddin

get the back started by the winshield slowly level the quarter panel down till the bolt holes match up

you want to make sure top and bottom line up with door panels this has the same motion as as drinking a glass of water tip top back till bottom seats on door well usually when you do the front clips you remove the doors cause of where the bolts are located

i hope this helped you some

May 21, 2008 | 1997 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...