Question about 1994 Saturn Sl

1 Answer

93 saturn twin cam starter removal

I have a 93 saturn twin cam four door, im trying to remove the starter and have the bottom bolt off but cannot locate the top bolt manuel says the bolt must be removed from the top of the engine near the manifold but cannot find it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 299 Answers

Top bolt is almost dirrectly above bottom bolt but,toward engine about 1 inch. slip 13mm.socket with enstention behind starter solenoid ,you have to fish for this bolt.Very hard if you do not have a rack,We always remove it from bottom.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size is the tensioner pulley. On a 1998 Saturn ls2 twin cam


The hex that you would use if you are trying to remove the belt is a 14mm I believe. The bolts to remove the tensioner from the engine are definitely 10mm.

Feb 26, 2015 | Saturn Cars & Trucks

1 Answer

Starter location on saturn sc1 1999


The Starter is located under the intake manifold on th back bottom side of the motor!
The only way to remove it is from under the car!
Remove the Neg Battery terminal from the battery before going under the car.
If I recall correctly, there are (2) 14 or 15mm bolts holding it to the engine block, one of them is a Blind bolt, as you will only be able to feel its location on the back side of the starter. (tip, when replacing the bolt behind the starter, either have a small magnet inside the socket to hold the bolt inside the socket while tring to locate the hole. You could also use a small piece of paper or plastic bag to wedge the bolt head to the socket so it doesn't fall out while tring to locate the hole!
You will also have a 13mm nut holding the Positive battery and Alt. cable to the starter and a 10mm nut holding the wire coming from the ignition switch.
Hope this helps!
Happy Saturn Motoring!

Jul 09, 2014 | 1999 Saturn SL

1 Answer

My 93 saturn twin cam sl2 series starter wont engage had it tested and its fine what could cause my starter not to turn all the way


If it is a random problem, you may have to wait until it is a solid failure to find the cause.
Could be the key switch, the neutral safety switch, the starter solenoid, or a cable connection.
A mechanic would check all of these components for voltage when it will not crank.

Aug 04, 2012 | 1993 Saturn SL2

2 Answers

Removed 1 bottom bolt from the starter of my '89


Seems I recall one of the bellhousing bolts ,it goes in 90 degrees from the bottom one.

Sep 08, 2011 | 1989 Toyota Corolla 2 Door

1 Answer

Where are the spark plug wires located on a 1995 grand am quad 4? Also how do you access the plugs?


This car has no plug wires. On the top of the engine you will see a cover that says twin cam.. There are four bolts in this cover. Remove the 4 bolts then gently work the cover back and forth while pulling up on it. It will lift up. The plugs are underneath this cover on top of the engine.

May 14, 2010 | 1995 Pontiac Grand Am

1 Answer

How do i put a starter in a 1998 saturn sl


disconnect the battery cables,,go under the car,the starter is under the intake manifold,,,disconnect the 13mm or 14mm nut one the starter and wire and then disconnect the 8mm or 10mm(different depending on years) and remove the wire,then you have to 13mm bolts that hold the starter to the engine,remove the top bolt first you cant see it but you can feel it,,,then remove the bottom one and the starter will fall out and thats it

Oct 20, 2009 | 1998 Saturn SL

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

1 Answer

How do you replace a drivers side window on a 1992 Saturn



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.


To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.

  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.

PICTURES ON NEXT POST!

Oct 13, 2009 | 2000 Saturn Ls 4dr Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...