Question about Dodge Intrepid

1 Answer

Fuel senior location on 99 dodge intrepid

Will not start clinking sound center of engine.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 103 Answers

If car making clinking noise you probably need a jump. If you ahve a good battery and car still won't start and makes that noise, you may need anew starter.

Posted on Mar 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 55 Answers

SOURCE: THERMOSTAT PICTUREDIAGRAM OF 1999 DODGE INTREPID, 2.7 ENGINE SIZE

It is located on the left side of the engine down where the lower rad hose meets the engine block. It is fairly difficult to change.

Posted on Oct 18, 2008

  • 373 Answers

SOURCE: location of waterpump on 2001 dodge intrepid 2.7

Hi....
The Water pump on your Intrepid 2.7L.
Is located in front of the engine, But you can't see because is inside of the timing cover.
And the Water pump is driven by the Timing chain.


I hope this help on your question.
Thank you for use fixya..

Posted on Jan 15, 2009

  • 1 Answer

SOURCE: 99 dodge intrepid blower motor not working

No. Pull out right front inner fender well cover and motor is on firewall. Four bolts max.

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: where is the fuel filter?

1999 dodge intrepid has map,egr,ect,and tps low and sometimes
high voltage codes.Idles fine but when giving some throttle it dies

Posted on Mar 10, 2009

  • 154 Answers

SOURCE: location of speed sensor a for 99 dodge intrepid

The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Posted on Apr 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Find out what is the black 2 screw pices in front of fuel system on dodge intrepid 3.2 99


I do not understand what you are trying to say. I believe that English is not your primary language but, I want to help and since communication is going to be tough, take a picture of the item that is clicking and I will identify it for you. Please, do not take offense to my lingual observations. The point I was trying to make is that what you are writing it is confusing. Okay?

Mar 22, 2014 | Dodge Intrepid Cars & Trucks

1 Answer

Repacing fuel filter on 1996 intrepid


1) Relieve the fuel system pressure by first removing the fuel pump relay from the Power Distribution Center. Then, start the engine and let it to run until it stalls. Try starting it again and allow it to run until it stalls. Continue restarting the engine until the car will no longer start. Turn off the ignition.
2) Disconnect one electrical connector from an injector. Use an alligator clip to connect an end of a jumper wire to either injector terminal. Connect the other end of the jumper wire to the positive side of the battery. Then, connect an end of a second jumper wire to the other injector terminal. Very briefly touch the other end of the jumper wire to a ground.
3) Locate the fuel filter, which is part of the fuel pressure regulator mounted on the fuel pump module. Disconnect the negative battery cable, then lower the fuel tank. Disconnect the fuel lines from the filter.
4) Remove the fuel line from the pressure regulator. Remove the filter/regulator by pushing in on the locking tab on the filter as you turn the regulator to unlock it. Then, pull it straight up.
5) Push the new fuel filter into the fuel pump module. Turn to lock it in place. Connect the fuel lines, and then you can reinstall the fuel tank. Check for leaks when you start the engine on your Dodge Intrepid.

Parts Of BMW.





May 30, 2012 | 1999 Dodge Intrepid

1 Answer

Can a 1999 dodge intrepid 2.7 liter motor fit in a 2002 dodge intepid that also contained a 2.7 liter motor are they compatible


look at the cars vin# on the door panel. the 99 model it will tell you what month and year the car was made such as 06/1999 if the 1999 model was made from 06/99 not before but 06/99 and above the engines will fit. also check the bolt patterns on the transmissions and starter location on each motor to see if in the same locations. if all match,they will interchange. thank you for choosing fixya.com

Jan 10, 2011 | 1999 Dodge Intrepid

1 Answer

Where is a fuel filter located at on a 99 intrepid


you will need to drop the gas tank if you want to access the filter,it's inside.
you should only have to replace this fuel filter if your fuel tank was contaminated with something other than gas,

Nov 22, 2009 | 1999 Dodge Intrepid

1 Answer

Location of speed sensor a for 99 dodge intrepid


The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Mar 29, 2009 | 1999 Dodge Intrepid

4 Answers

1999 Dodge Intrepid Dies while driving and sometimes won't start


I could very well be the TPS throttle position sensor acting up. I had a very similar situation on a 99 Concorde with the same engine in it in my shop today. Go to a shop that is able to do a data stream on the engine. What it is, is they hook up a scanner and have the ability to watch all the sensors as the car starts/runs.

Feb 12, 2009 | 1999 Dodge Intrepid

3 Answers

Where is the fuel filter?


1999 dodge intrepid has map,egr,ect,and tps low and sometimes
high voltage codes.Idles fine but when giving some throttle it dies

Feb 06, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...