Question about 2004 Porsche Cayenne

1 Answer

A squealing sound at the turning of the key to start the engine

It stops after the key is released and engine is running.But only turn the key for 1 second

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Porsche Master
  • 1,013 Answers

It's very likely a bad engine belt, or possibly your starter is going bad. Try putting a small amount of grease on the inside of the engine belt and see if the problem goes away after 1 or 2 starts. If it does go away (this is a very temporary "fix") you very likely need to replace the belt.

Posted on Apr 07, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CHEVY C1500 SQUEALING, IDLER PULLEY?


Without hearing the noise I can't tell you for sure but take a spray can of WD40 and with the engine running spray some on the belts if noise goes way that's your problem, if not check the A/C (if you have A/C) the compressor may be binding up causing the belt to squeal due to friction from the tight compressor. To check the compressor remove the belt and turn the A/C pulley by hand (should turn freely) next turn on the key (do not start engine) turn on A/C then turn A/C pulley by hand again. It will be harder to turn but still relativity easy. If it is hard to turn it is beginning to bind.

Mar 05, 2013 | Cars & Trucks

1 Answer

My alarm system went off due to wrong key ingnition...had to take a battery terminal off to stop the alarm, now I have the key and it wont start...is there a security reset?


Yes there is. 1. Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming. 2. Turn ignition to run position. (Allow ignition chimes to stop).
3. Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).
6. Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).

Aug 15, 2011 | 2002 Jeep Liberty

2 Answers

My car turns over good, acts like it might turn on then continues to turn. I figure it might be fuel filter since low fuel light had come on.Or could it be th fuel pump got hot and is not working properly?


common problem is turning car off with engine not reaching normal operating temp and floods engine. try this. DE-CHOKING PROCEDURE WHEN ENGINE CRANKS BUT DOES NOT START
If the engine does not start, try the following procedure to start the engine using the de-choke mode.
Failure to do so may aggravate the no start condition.
1. Depress and hold the accelerator pedal to the floor and crank the engine for 7-8 seconds. (This will clean out any unburned fuel from the combustion chamber)
2. Release the ignition key to stop cranking.
3. Release the accelerator pedal and start the engine. If the engine starts while performing Step 1 the engine will rev up. Immediately release the ignition key to stop cranking and remove your foot from the accelerator pedal.
^ Do not keep holding the ignition switch in the START position over 10 seconds if the engine does not start. This may result in a weakened or dead battery.
^ Avoid racing the engine or sudden take off right after starting the engine.
^ If the engine still fails to start following the De-choking procedure, have your vehicle inspected by your Mazda Dealer.

for your info there is a recall for this problem. contact mazda.

May 04, 2011 | 2004 Mazda RX-8

2 Answers

1998 buick skylark security theft light on,car starts and turns of right away?


Your PassKey Security System is malfunctioning. The most likely cause is a bad ignition lock cylinder. Try this to get it started:
1. Set the parking brake. (This will keep your headlamps from coming on and running your battery down)
2. Turn the key to the "START" position and release it to the "RUN" position. (Do not turn the key to the "OFF" position or you will have to start over.)
3. Leave the key in the RUN position for about 10 minutes until the SECURITY light stops flashing.
4. When the light stops flashing, turn the key to the "START" position again.


This should get the engine started so you can drive the vehicle to get it repaired.

Feb 23, 2011 | 1998 Buick Skylark

2 Answers

03 grand am 3.4l no crank at all. All the light on dash work good fuel pressure starter spins and engine starts and then stalls when jumping the starter directly installed new pass lock switch and...


If the Passlock switch has been replaced, the computer has to "learn" the new Passlock code. You will need to hook up a battery charger to perform the learning process. (It takes about 30 minutes with the key in the "ON" position and it will run the battery down.)

Step 1:

Turn the key to the "START" position and release to the "RUN" position. The "SECURITY" light will be flashing. After about 10 minutes, the light will stop flashing.
.
Step 2:

Turn the key "OFF" then back to the "RUN" position. (Do NOT try to crank it yet) The light will start flashing again. Wait about 10 minutes for it to stop flashing.
.
Step 3:
.
Turn the key "OFF" and back to "RUN" one last time. The light will be flashing again. This time, when it stops flashing, do not turn the ignition off. Instead, turn the key from the "RUN" position to "START". The engine should start and run. The computer has now learned the new Passlock code.

Please help myself and others by taking the time to rate my answer. Thank yoou for using fixya!

Feb 08, 2011 | 2003 Pontiac Grand Am

1 Answer

How to turn off change oil light on the 2004 Chevy Colorado Pick-up truck ?


1. Turn the ignition to ON do not start.Engine OFF dash board lights ON.
2. Press and release the reset button in the driver information center (DIC) until the OIL LIFE message is displayed.
3. Once the alternating OIL LIFE and RESET messages appear on the DIC display, press and hold the reset stem until several beeps sound. This confirms the OIL LIFE system has been reset.
4. Turn the key to lock. If the CHANGE OIL message comes back on when you start the engine, the ENGINE OIL LIFE system has not reset. Repeat the procedure
Alternate Method
1. Turn the ignition key to ON with the engine off.
2. Fully press and release the accelerator pedal 3 times within 5 seconds. Several beeps sound. This confirms the oil life system has been reset.
3. Turn the ignition key OFF.
4. If the CHANGE/OIL message comes back on when you start the engine, the engine oil life system has not reset. Repeat the procedure
I use the second method, it is more universal and it works for Chevy Venture too.

Nov 06, 2010 | 2003 GMC Sierra

1 Answer

I have a 2000 Buick Park Avenue. Sqeal coming from belt area


yes the tension needs to be adjusted or they sell belt dressing to spray on at the auto parts store

Jul 31, 2009 | 2000 Buick Park Avenue

1 Answer

Squealing sound


have the belts tightened or replaced as they are slipping on the pulleys by the sound of it

May 12, 2009 | 2000 Suzuki Grand Vitara

2 Answers

94 Montero keeps turning over but will not start?


i would say you probably guessed right and also check the air filter wires rotor bug and cap on the distributor unless its coil pack ign

Nov 13, 2008 | 1994 Mitsubishi Montero

Not finding what you are looking for?
2004 Porsche Cayenne Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...