Question about Hyundai Tiburon

1 Answer

2003 hyndia tiboron gt it has 3 codes on it po102 and po507 and po507pd i have replaced the sensors 3 times and it has high idle when you hit the gas a little i gse from 1000 to 2500 it dose not have

Bad idle control system

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 115 Answers

CHECK THE IACV (IDLE AIR CONTROL VALVE) UNDER THE HOOD!

Posted on Mar 29, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MobyMech
  • 106 Answers

SOURCE: miss fire #3 cyld. compression 125psi idle speed 2500 rpm

Hi

A faulty IAC would cause a random misfire rather than a misfire in a specific cylinder, as would an intake air leak, both of which would cause a high idle amongst other things.

Run the engine until its good and hot, disconnect the injector harness plug so the injectors are disabled, remove all the spark plugs, disable the ignition by unplugging the wiring connector(s) from the coil pack(s), and then carry out another compression test on al the cylinders.

If the compressions are now all relatively the same then you very highly likely have a faulty injector in cylinder 3.

Very best regards

Geordie

Posted on Jun 28, 2008

emissionwiz
  • 76846 Answers

SOURCE: "check system charging" is coming on at high RPM's

You have an alternator problem, have Kragen auto or a store like it test the alternator for proper operation, it's free.

Posted on Nov 14, 2008

  • 9 Answers

SOURCE: code po507

have you checked the idle control connector where it plugs into your throttle body for a good connection.

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: my engine idles very high, i can rev the throttle

throttle position sensor (TPS) possibly

Posted on May 04, 2009

fknstart
  • 404 Answers

SOURCE: check engine light p0171 system to lean bank one,

o2 sensor replace them

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 buick century po102 and po507 codes


P0102 is a Mass Air Fow Sensor code and wiil cause the car not to run right. Check the wires before replacing MAF has a high failure yet.

Sep 04, 2014 | Cars & Trucks

3 Answers

Code PO507, CLEANED THROTTLE BODY


you can do a relearn first reset clear mil -code if you can do it with scanner or disconnect battery for a few minutes ----start and let idle for 3 minutes and watch idle should start going down turn off for 60 seconds and let idle again for 3 minutes turn off for 60 seconds and start up and take a drive for about 20 miles need to have speed get up above 44miles per hour for a bit than off gas and let decelerate than back up on speed do this a few times while on drive throttle body should relearn

Apr 19, 2014 | Cars & Trucks

1 Answer

Crank sensor


These codes have to do with your MAF and Idle control sensor. I would try going to the auto parts store and buying a can of MAF cleaner. Remove the MAF sensor from the air filter box and spray it real good to clean it. (DO NOT) touch any of the wiring in the MAF as it's very sensitive. Just spray it and let it air dry for a few minutes. Also check the wire connector that the MAF plugs into. Unplug it and plug it back in after cleaning the contacts. If this doesn't work then you may need to buy a new MAF sensor. These range from $30.00 - $200 depending on the car. Once this is done, all the codes should go away. I doubt the p0507 is actually bad, That's your Idle control sensor. I believe if you fix the MAF codes the other will go away also.

Oct 26, 2013 | 2004 Nissan Quest

1 Answer

Check engine light on. troubleshooting code came back po507. had put gas that had water in it 3 wks ago.its been 2wks i got my nissian quest back. what could b problem


this code has nothing to do with the bad gas. The code states that your idle is too high. Take it back because they did not fix it yet since this is the same code.

Aug 03, 2010 | Nissan Quest Cars & Trucks

1 Answer

I changed the intake manifold on my 1997 gmc safari van that has the 4.3L engine. Now the check engine light comes on. it puts out 3 codes ( po102 ) ( po300 ) and ( po507). What did i do wrong and where...


its soaking air somewere around the manifold make sure you thigten the bolts on the wight pattern if yoou dont know the pattern start from te center to the outside or reset the computer just unhooked the negative cable from the batery for 5 minutes,

Sep 26, 2009 | 1997 GMC Sierra

3 Answers

I changed the intake manifold on my 1997 gmc safari van that has the 4.3L engine because of a coolant leak. Now the check engine light comes on. it puts out 3 codes ( PO102 ) ( PO300 ) and ( PO507). What...


you may have broke a gasket 0n the manifold and you now have a vacuum leak explaining the high idle. also check the iac sensor it may be stock partly open or sticking

Sep 25, 2009 | 1997 GMC Safari

1 Answer

Code po507


have you checked the idle control connector where it plugs into your throttle body for a good connection.

Apr 07, 2009 | 1999 Chevrolet Malibu

1 Answer

Fault codes, p0102,p0122,po507


po102--maf sensor, could be a bad air cleaner and not letting air into engine, po122--tps pedal position sensor low, replace or adjust tps sensor,or wiring,po507--idle control system high input. for this you can take off idle air control, and clean out carbon from were it mounts on engine. it is just before throttle body at end of air intake hose, it is black. do not push on pintle on end of valve when cleaning, use a old toothbrush to clean carbon off of valve, use carb cleaner but do not soak valve in liquid of any kind. good luck!!

Mar 20, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...