Question about Toyota Camry

Open Question

Balance shaft marking

2az-fe

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: toyota tarago 2az fe motor

Rustam.Where is the fuse for radio of 2003 toyota tarago

Posted on Jan 24, 2010

TDISLine
  • 1874 Answers

SOURCE: timing balance shafts on 2az

1. Remove the fan and generator V belt:

tdisline_502.jpg
tdisline_503.jpg
2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.

Drain the engine oil.

Remove or disconnect the following:
Negative battery cable

Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:

  1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.
  2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley

tdisline_504.jpg
Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine

tdisline_505.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine


  • Remove or disconnect the following:

    Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner
  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:

    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • tdisline_506.jpg
    Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine

    tdisline_507.jpg
    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    1. Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.
    2. Remove the bolt, chain tensioner and spring.
    3. Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    1. Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top.


    tdisline_508.jpg


  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine

  • Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.
  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_509.jpg

    Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine

    tdisline_510.jpg

    Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine

    tdisline_511.jpg
    Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine

    tdisline_512.jpg

    Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine

    tdisline_513.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    Posted on May 12, 2011

    emissionwiz
    • 75117 Answers

    SOURCE: timing balance shafts on 2az fe toyota

    Take a look at the engine below with chain installed

    9_24_2012_11_26_48_pm.jpg

    Posted on Sep 24, 2012

    davidhealey3
    • 1 Answer

    SOURCE: Where can I get the diagram to set the balance shaft marking for a Toyota 2az engine

    hi check this image out, i just got this for you.
    http://www.gto-northwest.co.uk/forum/download/file.php?id=111&t=1
    you will also find a larger image of the diagram with it.

    Posted on Nov 19, 2012

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Bank balance shaft 2az fe


    dealer will help know what that is

    Oct 17, 2014 | Cars & Trucks

    1 Answer

    Head toque settings


    double posted, back one. it 2.4 L right? not 2.2?
    d4d 2.2
    read the TSB on this engine and recalls>? for head gasket ?
    best is not to guess. do it right. an use the sequence chart.

    most HG fail soon after for not doing the 3 tests.
    warp head, warp deck, and surface conditions.
    see alldata.com
    better the FSM and all TSB on head.
    here is one on site spec. for both motors.
    2AZ-FE/D and/or 2AZ-FE/E Step 1: 52 ft. lbs. Step 2: plus 90 degrees my wild guess INSTALL and not removal? unsaid.
    front is left here, cam cog side left
    INSTALL SEQUENCE.

    F 8,6,1,2,9
    F10,4,2,5,7

    F= front or #1 cylinder end.

    take down is different order. (its aluminum, nothing trivial)








    Dec 14, 2013 | 2008 Toyota RAV4

    1 Answer

    BALANCE SHAFT SETUP MARKS FOR TOYOTA 2AZ-FE MOTOR


    A LOT OF SHOPS ARE HAVING TROUBLE SETTING THE BALANCE SHAFTS ON THE 2AZ-FE (AND IF YOU ARE ONE TOOTH OFF YOUR ENGINE WILL BLOW UP ) I AM A TOYOTA TECH AND HAVE SEEN THE DAMAGE THAT INCORRECT BALANCE SHAFT TIMING CAN CAUSE THERE IS A TOOL COMPANY CALL (TIMING SOLUTIONS) THE TOOL IS CALLED (THE 2AZSAVER) THIS TOOL COMES IN A CASE WITH VERY DETAILED VIDEO ON HOW TO PROPERLY SET BALANCE SHAFT TIMING ,THIS TOOL MAKES SETTING BALANCE SHAFTS VERY EASY

    Feb 18, 2013 | Toyota Camry Cars & Trucks

    1 Answer

    Where can I get the diagram to set the balance shaft marking for a Toyota 2az engine


    hi check this image out, i just got this for you.
    http://www.gto-northwest.co.uk/forum/download/file.php?id=111&t=1
    you will also find a larger image of the diagram with it.

    Nov 19, 2012 | Cars & Trucks

    1 Answer

    Timing balance shafts on 2az fe toyota


    Take a look at the engine below with chain installed

    9_24_2012_11_26_48_pm.jpg

    Sep 24, 2012 | 2003 Toyota Camry

    1 Answer

    I need timing marks on 2.2 toyota camry 2000


    1. Remove the fan and generator V belt:
    tdisline_542.jpg

    tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
    Before servicing the vehicle, refer to the Precautions Section.
    Drain the engine oil.
    Remove or disconnect the following:
    Negative battery cable
    Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
    1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

    2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
    tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
    tdisline_545.jpg

    Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

    Remove or disconnect the following:
    Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    Balancer shaft came apart ???????? crankshaft pulley keeps throwing balancer car won't accelerate balencer shaft timing marks keep coming off on recheck of timing belt new tps ,converter howlled for test...


    Sounds like the harmonic balancer - that also serves as the timing on a non distributor car has stripped the threads out. This usually - not always but usually requires a new crank shaft. Might be cheaper to just get a used engine.
    take down the vin number and ask the local dealer if there have been any recalls or service bulletins

    Dec 05, 2009 | 2001 Hyundai Santa Fe

    1 Answer

    Recently purchased a 2007 Camry, 2.4 Liter 4 cycle 2AZ-FE engine. My older 2001 camry had the oil filter located on the rear front (left side of the engine. Where is the oil filter located on my new c


    Your filter is visable by looking under the car. its near the exhaust pipe again, but toward the front of the car. tucked near the plastic air shield.

    Apr 29, 2009 | Toyota Camry Cars & Trucks

    2 Answers

    Toyota tarago 2az fe motor


    Rustam.Where is the fuse for radio of 2003 toyota tarago

    Jul 05, 2008 | 2003 Toyota Camry

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    42 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...