Question about Toyota RAV4

1 Answer

Cannot turn but has ignition light on.

No clicking or motor turning over when i try to start car!!! head deck stopped working, lights, trip gauge stopped. fuel and water gauge went passed full and hot marks when i pulled out the key. Makes two different kind of noises when key is in barrel (one normal and other is a weird beeping sound. When ignition is on and i press on the brakes, ignition turns off. All this happened in 1 day when trying to start the car up. someone please help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Battery terminals OK??? Battery OK??? Check for the fuse and circuit breaker for iginition.

Posted on Mar 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: A4 steering lock does not engage and car won't turn over

The steering locks don't necessarily engage when the key is removed, I always turn the wheel before exiting to engage it. There are several positions that will allow the pin to lock in but if between these, it may seem that it isn't locked.

Posted on Aug 23, 2008

  • 1 Answer

SOURCE: Car won't start

Your immobilizer is enabled. Try locking/unlocking the doors with the remote five (5) times, this should remedy.

Posted on Jun 05, 2009

CMR_Racing
  • 24 Answers

SOURCE: turn key nothing happens no clicking noises

Starter, altinator

Posted on Dec 13, 2009

  • 1428 Answers

SOURCE: my 99 vette makes a click sound when I try to

1. Starter issue.

2. Alternator bad.

Posted on Mar 19, 2010

  • 14036 Answers

SOURCE: The car wont start, the

TRY REPROGRAM KEY .PUT KEY IN IGNITION SWITCH TURN IGNITION SWITCH ON POSITION 20 SECONDS DONT START ENGINE WAIT 20 SECONDS TURN OFF SWITCH THEN TURN SWITCH BACK ON 20 SECONDS WATCH THE THEFT SECURITY LIGHT BLINKING.WHEN THEFT STOP BLINKING VECHICLE WILL CRANK.IF LIGHT STILL BLINKING.TRY FEW MORE TIMES KEY IN SWITCH ON POSITION FOR 20 SECONDS.MAKE SURE YOU HAVE THE CORRECT CAR KEYS IN SWITCH IF NOT WRONG SET OF CAR KEYS WILL SET OFF THEFT SECURITY SYSTEM.IF KEY RESETTING TRICK DONT WORK.CHECK BATTERY POWER MAKE SURE YOUR BATTERY HAS 12.5 VOLTS AND CHECK SECURITY THEFT FUSE.IF ALL LOOKS GOOD YOUR SECURITY HAS TO BE CHECKED OUT AT THE DEALERSHIP.

Posted on Oct 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2002 Trailblazer, when I start the engine, all my dash warning lights on and gauges stop working, the speedo and tach still work.


There is a known problem with the ignition starter switch that causes this, this is the switch that the ignition key operates when you turn it.

Sep 25, 2016 | 2002 Chevrolet TrailBlazer

1 Answer

Motor don't turn nothing dash lights and head lights 1985toyota pu


Do the gauges and warning lights work with key on? If not, check fusible links, AM1 for ignition key power. If the gauges/warning lights work, the key switch has power, so you can follow it to the starter solenoid. The start wire out of the ignition switch is a black/white wire, this is the hot wire to the solenoid, and only has power when key is held in start. With automatics, there is only one switch-a neutral start switch- between the ignition switch and the solenoid on the starter .

With a manual transmission, the black-white start wire goes to both a starter relay and a clutch start switch (on the clutch pedal), those two work together to send the power on to the starter solenoid. So, no crank, good battery, power to key, follow the black/white wire, the start relay and the clutch switch, to the starter solenoid- a hot wire there turns the starter motor on.

Mar 17, 2015 | Cars & Trucks

1 Answer

03 Pontiac Vibe after rear ended several electronics died


10 amp fuse under steering column that says it is for 'Gauge' fixed this problem. That fuse had blown.

Oct 23, 2009 | 2003 Pontiac Vibe

1 Answer

How to turn off change oil light on 2001 Corvette


Unless there is something wrong with you buttons the procedure is as follows:
1. Turn ignition key to ON (not start)
2. Press ENG MET button on trip monitor & release, then press it again within 5 seconds.
3. Within 5 seconds again press and hold GAUGES button until Change Oil lamp flashes.
4. Continue Holding Gauges button until lamp stops flashing & goes out.
5. You should be done, start & shut off car. If it didn't work turn off car and start from top.

Some buttons are very sensitive so try and be deliberate & steady when holding.

If that helps please rate my answers!
Brett

Mar 19, 2009 | 1994 Chevrolet Corvette

2 Answers

How do I turn off the change oil light on a 1994 corvette


1. Turn the key to “Run,” but don’t start
2. Press “ENG MET” on the Trip
the engine.
Monitor. Then, within five seconds,
press it again.
3. Within five seconds, press and hold
“GAUGES” on the Trip Monitor. The
“CHANGE OIL” light should flash.
4. Hold the “GAUGES” button until the
“CHANGE OIL” light stops flashing
and goes out. This should take about
ten seconds.
When the light goes out, the monitoirs
reset. If the monitor doesn’tr eset, turn the
ignition off, then try again.

Nov 18, 2008 | 1994 Chevrolet Corvette

1 Answer

1994 gmc safari


Sounds like your Passlock security system went into the tamper mode. If your dashboard security light blinks when the ignition is turned on, your Passlock security system is disabling the injector module, preventing the car from start. Try this:
1- turn the ignition on and just touch the starter, without getting the motor to fire, then leave the ignition in the "on" position. The security light will blink for about 10 minutes. When the light stops blinking, turn the ignition off and leave off for 3 minutes.
2-repeat the step #1, 3 or 4 times. You will know that is fixed when you turn the ignition on and the security light does not blink, then the car will start. Make sure to stay inside the car when you're doing this, as opening the doors will trip the security tamper mode on again. Once the tamper mode is off, the car starts and opening the doors will not trip the Passlock tamper mode.

Aug 06, 2008 | 1994 GMC Safari

1 Answer

Flashing lights! dash and headlights


RESET PROCEDURE

With the ignition off, press the TRIP and RESET buttons at the same time you turn on the ignition. HOLD the buttons for 10 sec and the instrument cluster will go into a diagnostic sequence. I dont have the codes but you can find them online (999 means ok).

Doing this procedure will reset the dash cluster which will solve most of the problems.
jcbrooks

Aug 05, 2008 | 1998 Dodge Caravan

2 Answers

Hi... i'm new to the foreign car market...


1st check the #4 fuse (10A) and #10 fuse (7.5A) on the 'under-dash' fuse block.
then #9 fuse (10A) on the 'engine bay' fuse block.

if the fuses are good, the gauge assembly has has "self-diagnostic" feature.

Self-diagnostic Procedure

The gauge assembly has a self-diagnosis function.
. The beeper drive circuit check
. The indicator drive circuit check
. The LCD segments check
. The gauges drive circuit check (speedometer, tachometer, fuel gauge, coolant temperature gauge)
. The communication line check (the coolant temperature signal line between the gauge and ECM/PCM)


Entering the Self-diagnosis Function:
1. Push and hold the trip/reset button.
2. Turn the lighting switch ON.
3. Turn the ignition switch ON (ll).
4. Within 5 sec., turn the lighting switch OFF, then ON and OFF again.
5. Within 5 sec., release the trip/reset button, then push and release the button four times repeatedly.

NOTE:
. While in the self-diagnosis mode, the dash lights brightness controller operates normally.
. While in the self-diagnosis mode, the trip/reset button is used to start the beeper drive circuit test and the gauge drive circuit check.
. lf the vehicle speed exceeds 1.2 mph (2 km/h) or the ignition switch is turned OFF, the self-diagnosis mode ends.

The Beeper Drive Circuit Check:
When entering the self-diagnosis mode, the beeper sounds five times.

The Indicator Drive Circuit Check:
When entering the self-diagnosis mode. the indicators lights (such as: Seat belt indicator light, Door/hatch indicator light, Brake system light. Charging system light, Low fuel indicator light, maintenance required light) blink.

The LCD Segment Check:
When entering the self-diagnosis mode, the odo/trip segment blinks five times.

The Gauge Drive Circuit Check:
When entering the self-diagnosis mode, the speedometer, the tachometer, the fuel gauge, and the coolant
temperature gauge needles go from the minimum position to maximum position, then return to the minimum position.
NOTE:
After the beeper stops sounding and the gauge needles return to the minimum position, pushing the trip/reset button, starts the beeper drive circuit check {one beep), and the gauge drive circuit check again.
The check cannot be started until the gauge needles return to the minimum position.

The Communication Line Gheck:
In the seif-diagnosis mode, after the odo/trip LCD segments check, the self-diagnosis starts the communication line check.
lf all segments comes on, the communication line is OK.
lf the word" Error" is indicated, there is a malfunction in the communication line between the gauge assembly, the multiplex control unit, and the ECM/PCM,
f4a412b.jpgc169609.jpg
Ending the Self-diagnosis Function:
Turn the ignition switch OFF.

Note: lf the vehicle speed exceeds 1 .2 mph (2 km/h), the self-diagnosis function ends.
-----------------------

If everything works correctly during the check, check your VSS (vehicle speed sensor)



Aug 03, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8737 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...