Question about 1998 Mazda 626

1 Answer

Car cranks but will not start

I have replaced fuel pump,spark plugs and wires

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Mazda Master
  • 808 Answers

This could go several ways #1 engine mechanical check cranking compression should have 125 psi or greater in all cylinders if low but even squirt oil (1/2 oz.) in 1 cylinder and retest goes higher then rings sealing has been lost. if uneven check timing belt for jumped or misalignment. #2 electrical does it have electrical spark to plugs crank engine with a spark plug connected to spark plug wire laying plug on engine can you see spark? No test ignition coil wires with a logic probe both terminals will be red with key on one will flash red/green when engine cranking does not the primary ignition needs repair Ignition module? or pick-up coil/ crank sensor. #3 fuel system pressure and injection pulse. injection pulse can be tested with logic probe DONOT USE A TEST LIGHT YOU CAN RUIN THE ECU .

Posted on Mar 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 158 Answers

SOURCE: ford telstar ignition coil f-694 and igniter deliver no spark

your distributor modual needs replacing

Posted on Apr 01, 2009

  • 14036 Answers

SOURCE: Mazda 323 Has spark, fuel, timing belt ok, does not want to start

check timing belt timing on the cam gear and crank gear. if timing belt has 60000 miles or more. if they dont break first. they stretch enough jump out of time.

Posted on Apr 09, 2009

rcampsr
  • 90 Answers

SOURCE: Do you know where or if a 2000 Mazda 626 has a

Hello, I am going to make a few assumptions here. The vehicle has an electric fuel pump and you replaced it. The vehicle has fuel injection. The engine is actually cranking, just not starting, when you say "car still won't crank". You are getting fire to the spark plugs at the plug ends. You checked the fuel pump for power at the pump. No power, then you back traced the wire to the fuse block and checked the fuse to see if it was blown. If the fuse is good back trace the power to the ignition switch and/or ECM for power. You have power at the pump, check the ground and make sure it is connected properly. Will the pump run when someone turns the key on? Pump runs, check fuel manifold for pressure. No pressure, check the fuel filter for blockage, or replace it. Fuel pump doesn't run, new replacement pump is defective. There is usually some type of control module for the fuel pump on fuel injected vehicles. Good Luck, RAC

Posted on Apr 18, 2009

  • 8 Answers

SOURCE: cannot start 1993 mazda miata

you may want to check your timing

Posted on Apr 19, 2009

  • 32 Answers

SOURCE: 94 MAZDA MX3 REPLACED FUEL

check the fuel pump relay. it is located under the hood in the fuse box directly in front of the battery

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A2000 ASTRO VAN IT QUIT WHILE DRIVING. I TRIED TO START BACK BUT BATTERY WENT DEAD, SO I GOT A BOOST, IT WOULD CRANK BUT NOT START. I GOT BATTERY TESTED IT WAS NOT HOLDING ENOUGH CRANKING AMPS SO I...


The fuel pump pressure shoud be 55-61 psi . Check for spark by removing a ignition wire at a spark plug and put a spark plug in wire and hold to engine ground and crank engine , if no spark then remove coil wire at cap and repeat.If still no spark then coil , module,,crank sensor or pickup may be the problem.
Check fuel pump pressure first and if available check for codes for possible crank sensor.

Feb 13, 2011 | 2000 Chevrolet Astro

1 Answer

Crank, won't start problem. I checked the spark plugs on Jeep 98. Looks good. Could it be the crank sensor or starter coil?


Yes it is very much possible.But there are many other possibilities too,including starter and spark plugs issue.

If your engine cranks normally but will not start because it has no spark, or it stalls and won't restart because it has no spark.

You can also do a test to confirm the problem .The procedure to do the test is as follows:---

If your engine has spark plug wires, disconnect one of the plug wires from a spark plug and place the end of the wire near a metal surface on the engine. Then insert a small Phillips screwdriver into the end of the wire (the plug boot), or a small bolt or nail to provide a conductive path. Then crank the engine and look for a spark to jump from the screwdriver, bolt or nail in the end of the plug wire to the engine. If you do not see a spark, there is an ignition problem.

OR-----------

If your engine has a coil-on-plug ignition system with no plug wires, In that case remove one of the coils from the spark plug and insert an old spark plug, a spark plug tester or a screwdriver into the end of the coil. Ground the spark plug or plug tester to the engine, then crank the engine and look for a spark. No spark indicates an ignition problem.If the engine has no spark, check for voltage at the coil positive terminal when the ignition key is on. If NO voltage, then problem is on the trigger side of the coil (pickup, crank sensor, ignition module or primary wiring circuit).

But If there is NO voltage at the coil itself, then in that case the problem is on the supply side (the ignition switch or ignition wiring circuit).-----------------

Jeep cranks but no start:----------------

A jeep that cranks over but doesn't start, in many cases will be due to a bad fuel pump, a broken timing belt, an inoperative cam sensor or crank sensor. Also these problems are related to faulty spark plug. Check the spark at spark plugs when you start the jeep. Do you notice any spark. Actually you should see. If in case there is no spark then it's a spark plug problem. Also the coil pack gives power to spark plug. So check the voltage at coil pack. It will show 12 volt. If there is no voltage noticed at coil pack then its faulty coil pack that has to be replaced. If all the possible options checked out ok then check the car starter. The starter gets power from battery to start the jeep. If the starter is faulty then it will not let the car to start. Also check and confirm that there is fuel in the jeep. If its very low fuel then in some cases this causes the problem. Also check and confirm that fuel pump is functioning properly and the fuel filter is not clogged. One of the easiest ways to check for a fuel pump related problem is to spray a little starting fluid into the air intake while trying to start the jeep. If the car starts momentarily, then there's a good chance the fuel pump is not working or the jeep is out of gas. You can also listen for the fuel pump's humming sound when the key is first turned on. Also if a inoperative fuel pump is suspected, a good technician will always check to verify there is power and ground being supplied to the pump, to eliminate the possibility of a bad relay or electrical issue. Fuel pressure can be checked with a pressure gauge and if there is pressure, pulse can be checked at the fuel injectors in several ways including the most common, with the use of noid lights. If the injectors don't have pulse the engine won't start. ---------- This troubleshooting tips will help you to solve the problem. Thanks. Helpmech.

Jan 07, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Wont start


is the your car engine cranking when you try to start, first check spark plugs ignition coils, remove one ignition coil and spark plug fix the spark plug in to the ignition coil then connect ignition coil to wiring and keep spark plug body touching on ground of engine head mettle parts, ask some one to crank engine then you can see is the plug sparking or not, do the same way to all the coils and plug otherwise you have to buy a ignition spark tester, is the all the coils and spark plugs are OK then check the fuel pump, it's sitting in under rear seat, before that do one thing disconnect oxygen (O2) sensor wiring and crank engine, the thing is if your oxygen sensor completely dead fuel pump will stop working, if engine start after disconnect O2 sensor, replace new O2 sensor, otherwise need to check fuel pump relay fuse and fuel pump. is this information helped you? please vote me and give a comment.

Oct 15, 2010 | 1998 BMW M3

2 Answers

My vw will crank but will not start running i


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the Schroeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.


Thank you!!

Jun 30, 2010 | 2001 Volkswagen Passat

1 Answer

RANDOM STARTING PROBLEMS; MOTOR SEEMS TO BE TURNING OVER FINE AND TRYS TO START; IF YOU WAIT AWHILE ALMOST ALWAYS START 1999 TIBURON


you may also have a plugged fuel filter if crank sensor and temp sensor turn out ok on the ohmmeter.
Next thing you will want to do is check for spark in each cylinder. You can pull one spark plug out, replug it back in to plug wire, lay on engine block, 1/4" form metal and the probe of plug, have someone else crank car, while you watch for spark. Then replace plug and wire and move on to then next. If you have one bad one, replace plug wire, if two or 3, it could be bad coil packs, if no spark, then it would be faulty module or crank sensor.

If spark is good, then you will want to check for fuel. You should have a fuel pressure test port on the fuel rail, with a rag, place over port, and press in valve to see if there is pressure. If no pressure, either fuel filter is plugged or fuel pressure regulator is faulty. As long as you can hear fuel pump turn on each time the ignition is placed in on position. If not, then relay or pump could be faulty.

Oct 08, 2009 | Hyundai Tiburon Cars & Trucks

2 Answers

1989 Cutlass wont start


the filter on fuel pump might be clogged as well or fuel pump needs replaced

Oct 01, 2009 | 1989 Oldsmobile Cutlass Ciera

3 Answers

"Cranks, but won't start". Replaced fuel pump, CKP, ICM & nothing


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..

Aug 27, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

1995 blazer was running rough, now not starting


if you believe some one put water or bad gas in your tank, then you will have to drain the tank. however, to know if you have water in your gas, first disconnect fuel return line or the line that goes in to the fuel pressure regulator put some fuel in a clear glass and let it sit for 15min.if you see white cloud at the bottom of the glass or water. drain the tank. if not check for spark by removing one spark plug wire and spark plug. place the spark plug in the spark plug wire boot and touch it on the metal part of the car. do not touch the spark plug itself only the booth with the plug in the boot. have some one crank the car over. if you see spark, the spark part is ok. but if no spark, check the coil with a volt meter it should be 3 to 8 ohm if not replace the coil. if ok, check for fuel by removing one spark plug or two and see if they are wet,if wet pump is ok. if not check the fuel pump relay and fuse. if fuse is blown replace. check relay with a volt meter. resistance of the relay should be between 40 to 80 ohm. not mega ohm,if mega ohm, replace. if not , listen to the fuel pump while some one is cranking the car. if you donot hear the pump, disconnect the pump electrical connector and applive 12 volt and ground to the pump by using a jumper or any wire and listen for pump sound. if not replace the pump. if there is sound coming from the pump, it is ok. check the fuel pressure regulator with a fuel pressure gauge or simply disconnect the vaccum from the regulator and try starting the car. if fuel pump is ok and spark is ok. then it maybe the computer or the crank position signal. also check the fuel filter it may be clog.

Jan 02, 2009 | 1995 Chevrolet Blazer

1 Answer

2004 Kia Sedona wont start but i can hear starter.


if the starter is revving very slowly it is the battery, charge battery. if not, It can be three things happing. 1 no spark 2 no fuel 3 no crank signal or the car computer is bad- you will need to unplug one of the spark wires and remove the spark plug and put the spark plug in the spark plug wire boot, and touch the spark plug on any metal on the car and have some start the car. donot touch the spark plug itself and see if there is a spark. if spark is bright, then it is not spark plug and wires but if no or spark is not bright, check the spark plug wires by applying a little bit of water on the spark plug wire and take a 12v test light, connect the clap to ground and and have some one to crank the vehicle, touch allover the spark plug wires with the tip of the test light, if you see spark, replace the wires and change the plugs.. they are not good. if spark is present, check for fuel by removing any one of the spark plugs and see if it is wet. if wet fuel pump is ok but if not go look for the fuel pump fuse and relay. is fuse blown, replace, check the relay resistor with a volt meter. it should be around 40 to 80 ohm. if everything is good from this point check the fuel pump itself by disconnecting the connector to the pump and apply 12v and ground using jumper wires or some wires to the fuel pump if you donot hear the pump,replace pump. if you, the crank signal or computer may be the problem

Jan 02, 2009 | 2004 Kia Sedona

Not finding what you are looking for?
1998 Mazda 626 Logo

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...