Question about Honda Cars & Trucks

1 Answer

Car won t move in any gear

I have a 2005 civic with a 5 speed manual trans it wouldn't move in anny gear so I replaced the clutch it drove for a block then did the same thing so I replced the trans and axels tried it again and still the same thing can it be 2 trans with the same problem

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 69 Answers

Did you also replace the pressure plate? Pilot bearing? If you replaced the clutch...and the car moved, and then stopped moving again...your issue is likely right there, bad pressure plate, flywheel may need resurfaced or replaced ETC. I am curious to know what the old clutch disc looked like when you took it out. Was it glazed or worn? I would pull the tranny again, and look at the new disc to see if it is glazed looking from slipping...and note if it is both sides, or one side, and which side...plate side or flywheel side. If you didn't replace the pressure plate/pilot bearing with the clutch disc...I would do that.

Posted on Mar 21, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Transmission noise - 93 Honda del Sol w/ 5-spd manual trans.

Imput shaft bearing. It just happened to me. You're looking at a $400 fix.

Posted on Apr 05, 2009

emissionwiz
  • 76848 Answers

SOURCE: 5-speed transmission making noise in 3rd and 5th gear

are u sure the alignment (side to side, up and down) of the trans on the bell housingis not out of spec, that will burn the bearings out very quickly.

Posted on May 04, 2009

  • 6982 Answers

SOURCE: HELLO EXPERTS I have a 1995 jeep wrangler with

Check all your hydraulic connections for seepage . If you find nothing leaking, check where the rod goes into the master cylinder under the dashboard...If still nothing, I'd change the master cyl, as it is likely internally bypassing and permitting the clutch to release. PS it takesa a special "touch" to shift gears without using the clutch, if you cannot do that don't drive it Till you get it fixed...you will damage synchros and will need to have trans removed and rebuilt. $$$you don't want to spend!!!

Posted on Jul 12, 2009

jeffbvegas1
  • 520 Answers

SOURCE: 95 saturn sl 2 5 speed manual transmission, clutch

This vehicle has a pair of shift cables which attatches to the shifter and runs to the transmission shift housing.To diagnose,removal of the center console is in order so you can inspect and verify the shifter/cable connections and movement,then verify the cables move the linkages properly at the transmission . These cables are a fairly common failed part and sold as the set,these are a dealer item and no aftermarket cables are available .

Posted on Sep 10, 2009

Testimonial: "That was nthe problem thanxs!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 honda civic 5 speed manual trans engine surges when down shifting from 2nd to 1st


Greetings & salutations Robert Avila,

(First question on FIXYA... Welcome).

Your engine surging and what gear you
"DOWN-SHIFT" to ... ought have very little in
common save for one condition (I can think of)...

Your clutch RELEASE is MARGINAL..!!

Check your master/slave clutch cylinders to see
if there is any leakage (fluid might also be low)...

These are not EXPENSIVE and USUALLY fail
in pairs...

If the surging happens with the clutch released... that
is a WORN CLUTCH DISC (replacement time)...

Actuator (slave)
2005 HONDA CIVIC 2 0L L4 Clutch Slave Cylinder RockAuto

2006
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+slave+cylinder,2044

Activator + reservoir (Master)
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+master+cylinder,1996

Else (not-so-easy (certainly doable))... CLUTCH DISC
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+friction+disc,10605

Standard Information...
STOCK (less than $35 (assuming only wear)):
More Information for PACT 99661D

Honda is almost a DELIGHT to work on...
Mechanics manual is a MUST.

MOST IMPORTANT tip of this entry...

NEVER EVER ever let the weight of the transmission
be SUPPORTED by the input shaft...

You will be proud.

Carnac the Magnificent

Oct 23, 2017 | Honda Cars & Trucks

1 Answer

'03 Civic Si 5 speed k20a3 Having trouble shifting at higher rps. Shifter resist moving into next gear. Clutch grabs as it should and there are no hydraulic leaks or malfunctions.


Expect that the clutch is dragging. The plate may be warped maintaining a spin on the transmission input putting an excessive wear on the synchronizers.

Inspect clutch.
Inspect pilot bearing

Hope this helps.
im001730-hioxyjzsrsihrx1txyibv0ns-4-0.jpg

Jun 29, 2017 | Honda Cars & Trucks

1 Answer

My 2001 Honda civic will not move Its a five speed and the shifter goes into any gear without pressing the clutch in When I do put it into gear and try to move it just rolls like its in neutral Clutch?


Not necessarily. Check that the clutch slave cylinder is not being held in the disengaged position by a blocked clutch master cylinder. Check this by opening the bleed nipple and if the clutch arm moves to engage the clutch then replace the clutch master cylinder as the compensating port is blocked.

Jan 06, 2014 | Cars & Trucks

1 Answer

Manual trans goes in gear but car won't move


think you will need to replace clutch as it sounds like the lining has broken up on the friction plate

Dec 31, 2013 | 2000 Honda Civic

1 Answer

2000 civic wont drive


Sounds to me that you might have lost your pressure plate or the throw out bearing. The only way to check is to pull your trans out and see if the presure plate is broke or the throw out bearing id gone. Sorry no quick fix on this one. It;s not a bad job to change the clutch assem. but it is time consuming.

Dec 04, 2012 | 2000 Honda Civic

1 Answer

Manual 5 speed Trans, Jumping out of gear


bummer,gotta be the 3rd syncro,has to come apart to fix it.

May 16, 2012 | 1991 Honda Civic

1 Answer

My 1998 Honda civic ex won't move but the motor


Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

1 Answer

Gears are all moving without the clutch car does not move on any gear 1991 honda civic breeze


When you said without clutch I'm assuming you mean w/out clutch pedal pressed down. Assuming that, and you have the trans in gear with foot off clutch pedal, and vehicle will not move then it sounds like the clutch disc or pressure plate is worn out. These parts wear out just like brake pads or even the bottom of your shoes. Once it's done they have to be replaced.

Sep 20, 2010 | 1991 Honda Civic

1 Answer

Transmission noise - 93 Honda del Sol w/ 5-spd manual trans.


Imput shaft bearing. It just happened to me. You're looking at a $400 fix.

Mar 22, 2009 | 1994 Honda Civic Del Sol

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...