Question about 1990 Chevrolet Lumina

Open Question

R&R turn signal switch

Not working

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signals don't work and I've checked the bulbs, fuses & flasher.


About all that is left on the list is the turn signal switch.
Do you have power in and out of the switch ?

Feb 04, 2013 | 1995 Buick Skylark

1 Answer

2001 Town & country brake lights not working, but the third brake light and tail lights are working. I also just replaced the brake light switch thinking it was the problem, but it wasnt


I think the brake light and turn signal are on the same bulb on these, correct?

If so do the turn signals work?

If they do than I would bet that the turn signal switch itself is the problem. The power for the brake lights is routed through the switch (except for the third brake light that is supplied power directly form the brake switch). The turn signal switch will interrupt power from the brake switch and supply power from the turn signal flasher depending on if the right or left turn signal is engaged.

Sometimes wiggleing the lever or pushing the four way flasher button with the brake pedal depressed will intermittantly cuase the brake lights to work. If this is the case than it is the turn signal switch that is causing the problem.

Feb 11, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

I replace my brake switch & my light don't work? when i stop


IF THE FUSES INSIDE THE CAR & UNDER THE HOOD HAVE ALL BEEN CHECKED WITH A GOOD FUSE TESTER, & THE BRAKE LIGHT SWITCH REPLACED, THE TURN SIGNAL SWITCH IS NEXT. THE BRAKE LIGHTS GO THROUGH THE TURN SIGNAL SWITCH SO THEY CAN BE USED AS TURN OR BRAKE LIGHTS. I'M ASSUMING THE BULBS ARE OK. REMOVE THE PLASTIC FROM AROUND THE TURN SIG. SWITCH. STAY AWAY FROM ANY WIRES THAT ARE IN THE YELLOW SLEEVE. THEY ARE AIR BAG WIRES. WITH BRAKE PEDAL DEPRESSED, THERE SHOULD BE POWER IN THE WHITE WIRE. IF THERE IS NO POWER IN THE WHITE WIRE, YOU MAY HAVE TO PUT A BYPASS WIRE FROM THE WHITE WIRE COMING OUT OF THE BRAKE LIGHT SWITCH TO THE WHITE WIRE GOING INTO THE TURN SIGNAL SWITCH. IF THAT DOESN'T MAKE THE BRAKE LIGHTS WORK, THE TURN SIGNAL SWITCH MUST BE BAD.

Jan 26, 2011 | 1999 Chevrolet Malibu

1 Answer

Have a 1999 Chev. Suburban. Problem is with brake lights. Top panel (on roof) works but neither side panel works. Replaced circut boards in tail lights, new bulbs, and all fuses are good. What next?


WITH A GOOD FUSE TESTER, TEST ALL THE FUSES FUSEBOX UNDER THE HOOD & INSIDE THE VEHICLE. IF THE FUSES ARE ALL GOOD WITH THE TESTER YOU MUST HAVE A BAD BRAKE LIGHT SWITCH OR A BAD TURN SIGNAL SWITCH. THE BRAKE LIGHT CIRCUIT GOES UP THROUGH THE TURN SIGNAL SWITCH & THEN TO THE BRAKE LIGHTS. FIRST OF ALL IS THE BRAKE LIGHT SWITCH GOOD ? THE ORANGE WIRE FEEDS THE BRAKE LIGHT SWITCH, THE WHITE WIRE PUTS POWER TO THE TURN SIGNAL SWITCH, SO THE LIGHTS CAN BE USED AS TURN LIGHTS OR BRAKE LIGHTS. , PUT A TESTER IN THE WHITE WIRE & PRESS ON THE BRAKE PEDAL. IF THE TEST LIGHT LIGHTS UP, BRAKE LIGHT SWITCH IS GOOD, BY THE WAY THE BRAKE LIGHT FUSE MAY BE LABELED" STOP", THE FUSE LABELED" BRAKE" IS FOR THE ABS SYSTEM. TO CHECK THE TURN SIGNAL SWITCH FOR BRAKE LIGHTS, REMOVE THE PLASTIC COVER FROM UNDER THE STEERING WHEEL, PRESS ON THE BRAKE PEDAL, PUT THE TESTER IN THE SMALL YELLOW WIRE, THEN THE SMALL GREEN WIRE. IF THERE IS NO POWER IN EITHER WIRE, THE TURN SIGNAL SWITCH IS BAD.

Jan 11, 2011 | 1999 Chevrolet Suburban

2 Answers

1992 Cadillac Brougham 5.0 L V8 RWD, turn signal don't work.


The turn signal switch is most likely the problem,but change the flasher for the turn signals first,some times this is all that it is.

Jun 11, 2010 | 1992 Cadillac Brougham

2 Answers

Left turn signal doesnt work and my brakelights


  1. Check the fuse make sure it is not busted and also use a designated amp only.
  2. Check the bulb and the wires also.

Mar 28, 2010 | 1997 Chevrolet Lumina

1 Answer

1998 Cavalier rear turn signal doesn't work


The turn signal switches are known to go bad, try to use the turn signal switch and jiggle the lever after clicking to the left turn. Replace signal switch assembly.

Jul 19, 2009 | 1998 Chevrolet Cavalier

1 Answer

Turn signals & brake lights quit working


there is a relay that goes to the turn signals.......and there is a switch that goes to the brakes......check them...

May 14, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
1990 Chevrolet Lumina Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...