Question about 2010 Peugeot RCZ 1.6

Open Question

How to install front bumper

Need to reattach the front bumper as it was pulled off when parking

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do I need to remove the front bumper on my 1992 Cadillac Deville to chang parking light bulbs?


Kind of a silly question, removing a
bumper for a parking lamp

How about getting under it before you came here
& reach up & turn the lamp socket & pull it out &
check the bulb/lamp

Oct 31, 2014 | Cars & Trucks

1 Answer

How do you remove the front bumper of a Mercedes Benz cl65 amg


Lift the front end of the car and support on stands.
Remove the front wheels.
Remove the fowards under-tray.
Remove the forward halves of the front wheel arch liners.
Unscrew the small down-facing Torx screw at each top rear corner of the bumper.
Gently pry inwards the rear end of the U-shaped steel channel that holds the fender and bumper flanges together.
Pull the channel rearwards to disengage the lugs from the diagonal slots at the forward end, and remove the channels.
Disconnect the external air temp sensor in the bottom left air intake.
Disconnect the parking sensors connector at the right rear corner. You need to open the lever lock and pull hard without damaging the wiring.
Open the hood and remove two bolts on top of the bumper, next to the inner headlamp mountings.
Remove two nuts in lower grille - vertically beneath above bolts.
If its your first time, get a friend and pull the bumper forwards very slowly and gently, avoiding scratching the fenders.
The bumper is surprisingly light.

It will take about an hour.

Jul 02, 2014 | Cars & Trucks

1 Answer

I need to reattach the rear bumper


autozone will have that replacement hardware in the body aisle its usually some assorted bolts, and plastic clips''if the car needs moved to get there, may need to wire tie it up enough or remove entirely to go there(or any closer parts or body shop.

Feb 09, 2013 | 1998 Pontiac Bonneville

1 Answer

How to change headlight lamp in 2005 Pontiac g6


To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Dec 25, 2010 | Pontiac G6 Cars & Trucks

1 Answer

One side of front bumper cover is hanging down on my 98 handa


You should remove the bumper cover and take a look and make sure that the cover is not broken, its all plastic and the hold down arms sometimes break off and bumper will hang, also look for missing or loose fastners,

May 28, 2010 | 1998 Honda Civic

1 Answer

I need to replace a foglamp bulb right side.I have fairly easy access to & can see the rubber housing for the bulb,but cannot figure out how to remove it.Do I need to rermove the entire assembly in...


Typically the fog lamp is located in the front bumper assembly. It's usually fairly easy to access and replace these.

Place the car is park, secure parking brake. Use a creeper to scoot under the front end of the car, look up into the bumper. Located the backside of the fog lamp holder. You would usually grab and twist counter clockwise about an inch, then pull straight out. Push in on the bulb while turning counter clockwise until it pulls out of the lamp holder.

These fog lamps usually have a little bit of cushioning grease in the socket. Do not remove the grease or connectivity problems will result with the new fog lamp. Push the new bulb in, turn clockwise until bulb stops turning, release hand pressure.

Installation is the reverse of removal.

May 25, 2010 | 1999 Oldsmobile Eighty Eight

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

1 Answer

How do I reattach the front bumper? the left side partially came off.


remove plastic rivets and bolts holding bumper within fender well, between lights near hood latch, and bottom of bumber, be careful taking bumper off to prevent cracking. exact opposite for installing bumper

Jun 17, 2009 | 1996 Honda Accord

2 Answers

How to change the whole headlight assembly on a 05 Honda CRV


You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.

Dec 23, 2008 | 2005 Honda CR-V

1 Answer

Front Bumper


Chances are the shop that initially replaced your bumper didn't do it right and the shoddy install left it sitting lower than it should have. Because of this, you were able to snag the bumper on the parking block. The reason you have to replace it is most likely the mounting bolt holes were torn out or otherwise damaged when the bumper was caught, and there is no longer a mounting surface to use with new mount bolts to put the bumper back on.

Jul 29, 2008 | 2007 Audi A4 Convertible

Not finding what you are looking for?
2010 Peugeot RCZ 1.6 Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...