Question about 1995 Oldsmobile Aurora

1 Answer

Its when i take out the key and lock the doors that the headlights come on

Car is off keys out of ignition the headlights turn off and on i have take out battery

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

This is caused by you delay switch or relay staying in the closed position causing it to short out . or if your headlight switch is on the steering colume and acts as a signal light switch used for low and high beam will need replacing

Posted on Mar 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 726 Answers

SOURCE: 1998 Oldsmobile Aurora Lighting problem-car

benimur is right thats what it will be

Posted on Aug 03, 2008

keemo68
  • 1263 Answers

SOURCE: 2002 oldmobile bravada ignition key is stuck in lock position

try and turn your steering wheel a little bit left or right and and the same time try and turn the key when it turns toward the dash then try and turn the key back. try and repeat this several times if neccessary. this should work. please rate this solution. thanks

Posted on Aug 30, 2008

  • 373 Answers

SOURCE: 1993 Oldsmobile Cutlass Ciera won't turn over (crank)

First step is see the Condition of the oil.
Them you need to see if the ENGINE is NOT LOCKED UP.
To Do that, you will need a Rachet and Socket to Try TURN the CRANKSHAFT pulley by Hand.
If you are ABLE to Rotate,
And the Battery is good, Check all the Connection from the BATTERY to the STarter motor,
And the Ground Cable. From battery To the Chassis and the Bolt at the Transmission.

But if you are Unable to TURN over the Crankshaft Pulley.
The Engine is Locked up.
And will need to take a Opinion of a Mechanic .
To be sure Of the problem and the condition that may affect to the ENGINE went damaged.

I hope this help on your problem.

Thank you for use fixya...

Posted on Sep 24, 2008

stormbrewin
  • 426 Answers

SOURCE: how to get key out that is stuck in ignition

Remove steering column shroud(cover)and tap ignition barrel with small hammer while twisting key backwards and forwards,also turn steering wheel backwards and forwards sometimes this is enough to release key as the locking pins in barrel and the steering lock pin do sometimes jam.You will have to remove steering column shroud to replace ignition barrel if tapping/hitting it doesnt work anyway so its not a wasted effort.Good luck,let me know how it works out

Posted on Nov 12, 2008

lilmikew99
  • 105 Answers

SOURCE: key wont turn in ignition

try wiggleling the key too the tumblers may be getting worn in the ignition is this works then replace the ignition

Posted on May 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coding spare key for a Toyota Echo?


Adding key.
Note:
You must be having one working master key to perform this function.
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

Jan 09, 2013 | 2001 Toyota Echo

1 Answer

My key will not open the doors or start the engine (it won't even turn in the ignition switch). Initially, I thought it was the battery for the key, but I changed that without success. The light on the...


It's possible that your key is bad or no longer works. A way to verify that it is a key problem is to see if the 2nd key or spare key works properly. Check the side of the remote key for a 3 digit #. if the key variant is less then 221 the way to reset it is to put it in the ignition and pull it out 5x with 8secs. If higher than 221 then the no need to try and reset remote key.

Sep 27, 2010 | 2001 Mercedes-Benz C-Class

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

On my 1998 Dodge caravan nothing works such as horn, headlights, breaklights, door locks, etc. without the key being turned to accessories or ignition. When I turn on the key these everything works. I...


seams like the problem is in your ignition wires that are behind the ignition key cylinder they are not making the contact it should after releasing the key

Aug 22, 2009 | Dodge Caravan Cars & Trucks

1 Answer

Redo code for 2007 Pilot key


ok get in the car, close the door, make sure all doors are closed.... put the key in the ignition, turn the key to on but without starting the car (lights on dash light up only) press and release the key lock button, turn key to off, without removeing the key.. turn to on without starting the car (dash lights up only) press and release the key lock button again, turn the ignition off, without removeing the key then turn back on (lights on dash on only without starting the car, press and release the key lock button , turn off the ignition without removeing the key, ..turn on the ignition once more without starting the car , press and release the key lock button and u should hear the door lock cycle ....leave the key in the ignition ... now press the lock button or unlock button on the other remotes one at a time if u have them.....u should hear the lock cycle indicateing all remotes are programmed.... kind of tricky to explain but you will get it, the sequence of turnin the key in the ignition on and off is only done with that one first key,,, remember after the door lock cyles press the lock or unlock button on the other remote fobs if if any...and ur done..may take u a few trys.. let me know how it worked out.

Apr 06, 2009 | 2007 Honda Pilot

1 Answer

Car thinks the key is still in the ignition


There is a little button inside the ignition switch that gets pushed out of the way when the key is inserted, and sometimes that button gets stuck in the closed position. It will chime until that button is released. You might have to replace the ignition switch. Sometimes you can play around with the key in the switch, or use a pick to work it free. Hopefully this can help you fix the problem. Best wishes.

Jan 16, 2009 | 2005 Chevrolet Tracker

4 Answers

Program a remote key for 03 A6


I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.

Dec 10, 2008 | 2003 Audi A6

4 Answers

Code to program my key fob


Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode

Oct 25, 2008 | 1999 Oldsmobile Intrigue

Not finding what you are looking for?
1995 Oldsmobile Aurora Logo

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...