Question about Honda Cars & Trucks

1 Answer

2002 cr-v has a fuel leak from top of tank at the fuel pump port

Fuel is leaking from the black ring at fuel pump inspection port

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 25 Answers

The o -ring can be changed and purchased separately as long as the fuel pump is working properly im sure someone was in there if the o-ring is not seated properly the pump has a spring load on it u have to place o-ring, push pump down ,and either screw in or turn the lock ring danny

Posted on May 03, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Gas leaking from on top of the tank

Thanks!

Posted on Aug 19, 2008

  • 6 Answers

SOURCE: 2002 Chrysler Town and Country gasoline odor

check your fuel injector gaskets

Posted on Jan 04, 2009

dealt_soul
  • 296 Answers

SOURCE: 92 accord lx leaking on fuel rail

Dont replace just one O ring on the injectors. You need to replace all when you replace them. It sounds like you still have O ring leaks.

Posted on Jan 19, 2009

SOURCE: FIxing a leak between the fuel tank and the fuel

your best bet is to replace the fuel filler neck. the entire fuel system is a calibrated emissions system, meaning any changes to the specific setup may set a check engine light. you should be able to purchase a new fuel filler tube at your local dealer, not sure if parts stores carry those kind of parts. but you can try them too.

Posted on Feb 21, 2009

  • 36 Answers

SOURCE: fuel tank leaking how to

If your gas tank is cracked or has a hole in it, you have to drain the tank, remove the gas tank and replace it, or have it repaired (if possible). If the gas tank is just leaking from the top and dripping along the side and to the bottom, you will still have to empty the gas tank, and remove it to get a good look at the condition of the gasket. It is not uncommon for these gaskets to become cracked or fragile over time because of the harsh chemicals and cleaning agents used in unleaded gas. If you do decide to have the gas tank removed, I would recommend replacing the fuel pump and fuel filter if your car has high mileage. Please rate this response if you found this helpful.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I replace a bad fuel module o-ring 2002 Sebring 2.7L v6


sorry dont think you will be able to check this link out he's the chrysler expert
How to Replace Fuel Pump in Chrysler Sebring eHow

Mar 29, 2014 | 2002 Chrysler Sebring

2 Answers

Leaking fuel pump


If the fuel is leaking into the car you will need the replace the seal on the top on the pump assembly not the seals on the pump itself but before changing the seal just double check the fuel lines are tight and the leak is actually from the fuel splashing out of the tank. The seal your after is referred to as the pump assembly oring ( big rubber oring around the top of the assembly a smear of silcone can be used as a temporary fix but erge you to get it fix properly as soon as possible and fuel fumes in the cabin can be extremely deadly)
Hope this helps

Jan 15, 2014 | 2003 Nissan Altima

1 Answer

How to change a fuel pump


fuel pump can be access through lifting up rear seat or through an opening access or inspection cover in the trunk compartment.if you dont see no fuel tank inspection cover the fuel tank need to be lowered.remove top cover 4 screws to get top cover off to get to fuel pump assembly.

Jan 11, 2012 | 1995 Nissan Altima

2 Answers

Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
Removal
  1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
  1. Remove rear seat cushion. Refer to Section 01-10.
  1. Remove plastic grommet from floor pan.
  1. Disconnect fuel pump module electrical connector.
  1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

    Disconnect fuel and vapor return tubes from fuel pump module.
  1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
  1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

    Remove fuel pump module and cover fuel pump module opening in fuel tank.
  1. Remove fuel pump module O-ring seal and discard.
Installation
  1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

    Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
  1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
  1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
  1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
  1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
  1. Connect fuel and vapor return tubes to fuel pump module.
  1. Connect fuel pump module electrical connector.
  1. Install plastic grommet in floor pan.
  1. Install rear seat cushion. Refer to Section 01-10.
  1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
  1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
  1. Remove pressure gauge, start engine and recheck for leaks.
Hope this helps

Aug 13, 2011 | 1996 Mercury Mystique

1 Answer

Location of and how to remove and replace - 2002 DeVille Sending Unit/Fuel Pump Module (4.6L engine)


These units are in the tank and must be dropped in order to replace.


WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

  1. Relieve the fuel system fuel pressure, as outlined in the Fuel System Section.
  2. Drain the fuel tank to at most 3/4 of a tank full.
  3. Raise the vehicle.
  4. Remove the fuel tank.
    NOTE The modular fuel sender support assembly will spring-up when the locking ring is moved.
  5. Remove the fuel sender assembly using tool J39765 Fuel Sender Locknut Wrench or an equivalent.
  6. Note the position of the fuel sender strainer for installation.
  7. Support the reservoir with one hand and grasp the fuel sender strainer with the other hand.
  8. Pull the external fuel sender strainer off of the fuel sender.
  9. Inspect the fuel sender strainer. If the fuel sender strainer is contaminated, the fuel tank should be cleaned.
  10. Discard the fuel sender strainer after inspection.
  11. Disassemble the electrical connectors from the fuel level sensor assembly of the fuel pump and cover assembly.
  12. Disassemble the fuel level sensor assembly.

    0996b43f802054cc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fuel level sending unit on fuel sender (fuel pump) module.


To install:
  1. Assemble the fuel level sensor assembly.
  2. Assemble the electrical connectors to the fuel pump and cover assembly.
  3. Position the new fuel sender strainer on the modular fuel sender and push on the outer edge of the fuel sender strainer until the fuel sender strainer is fully seated on to the sender assembly.
  4. Install the fuel sender assembly into the fuel tank using tool J39765 Fuel Sender Locknut Wrench or an equivalent.
  5. Reinstall the fuel tank.
  6. Lower the vehicle.
  7. Add fuel to the fuel tank.
  8. Connect the negative battery cable.
  9. Reinstall the fuel tank filler pipe cap.
  10. Inspect for fuel leaks.
  11. Turn the ignition switch ON for 2 seconds.
  12. Turn the ignition switch OFF for 5 seconds.
  13. Turn the ignition switch ON .
  14. Check for fuel leaks.

Oct 26, 2010 | 2002 Cadillac Deville

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

1 Answer

Replace fuel pump for 2002 gmc sierra 2500


First...this is where the pump is (gas tank) on the engines listed:

6f9f9d7.gif

Illustrating fuel pump and sending unit sensor (3) on 1999-2005 4.8L, 5.3L, 6.0L Engines


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
  3. Relieve the fuel system pressure.
  4. Drain the fuel tank.
  5. Remove or disconnect the following:
    • Fuel tank
8e4564e.gif
WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

  • Fuel sender assembly retaining ring using a fuel tank sending unit wrench. Remove the fuel sender assembly and the seal. Discard the seal.
  • Note the position of the fuel strainer on the fuel sender. Support the fuel sender assembly with one hand and grasp the strainer with the other hand. Pull the strainer off the fuel sender. Discard the strainer after inspection. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
    • Fuel pump electrical connector
    • Electrical connector retaining clip from the fuel level sensor
    • Sensor electrical connector from under the fuel sender cover
    • Fuel level sensor retaining clip
  • Squeeze the locking tangs and remove the fuel level sensor.
  • Remove the fuel pressure sensor.
  • To install:
    1. Install or connect the following:
      • Fuel pressure sensor
      • Fuel level sensor
      • Sensor retaining clip
      • Electrical connector to the fuel level sensor
      • Electrical connector retaining clip to the fuel level sensor
      • Fuel pump electrical connector
      NOTE Always install a new fuel strainer when replacing the fuel tank fuel pump module.

      • New fuel strainer in the same position as noted during disassembly. Push the strainer on the bottom of the fuel sender until the strainer is fully seated.
      • New seal on the fuel tank
      NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the fuel sender assembly, assure that the fuel pump strainer does not block full travel of the float arm.

      • Fuel sender assembly into the fuel tank
      • Fuel sender assembly retaining ring
      • Fuel tank. Install the fuel tank strap attaching bolts. Tighten the bolts to 30 ft. lbs. (40 Nm).
    2. Refill the fuel tank. Install the fuel filler cap. Connect the negative battery cable.
    3. Turn the ignition ON for 2 seconds.
    4. Turn the ignition OFF for 10 seconds.
    5. Turn the ignition ON.
    6. Inspect for fuel leaks

    Oct 25, 2009 | 2002 GMC Sierra 1500

    1 Answer

    Remove fuel pump from tank ford windstar 98


    To gain access to the fuel pump, it is necessary to remove the fuel tank.
    1. Depressurize the fuel system and remove the fuel tank from the vehicle.
    2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
    3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
    4. Remove the fuel pump module.
    5. Remove the seal gasket and discard it.

    To install:
    1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
    2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
    3. Install the tank in the vehicle.
    4. Install a minimum of 10 gallons of fuel and check for leaks.
    5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
    6. Check for fuel leaks at the fittings.
    7. Remove the pressure gauge.
    8. Start the engine and check for fuel leaks.

    May 26, 2009 | 1998 Ford Windstar

    1 Answer

    Gas smell outside and inside


    don't over fill the tank, when it clicks off thats it!! any check engine light? I had fuel smell, and the O-Ring was leaking when I changed the fuel pump. Top of the fuel tank, was leaking only on a full tank, Also evap, pump and hoses do crack and leak but it will show, in a check engine light usually

    May 12, 2009 | Dodge Caravan Cars & Trucks

    1 Answer

    Fuel pump on 2002 pontiac firebird 3.8 v-6?


    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Relieve the fuel system pressure.
    3. Drain the fuel tank.
    4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
    5. Remove or disconnect the following:
      • Fuel tank
      • Fuel sender-to-fuel tank retaining ring
      • Fuel sender from the fuel tank
      • Fuel pump from the sending unit 0900c152800a02fb.jpgFuel sender/pump assembly component identification
    To install:
    1. Install or connect the following: NOTEThe fuel pump strainer must be in a horizontal position and must not block the float arm travel.
      • Fuel pump with new strainer onto the sending unit
      • New O-ring in the tank opening groove
      • New O-ring on the fuel sender feed tube
    2. Fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
      • Retaining ring
      • Fuel tank. Torque the bolts to 33 ft. lbs. (45 Nm).
      • Fuel filler cap
      • Negative battery cable
    3. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks

    Sep 24, 2008 | 2002 Pontiac Firebird

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    46 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7697 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...