Question about Toyota Tacoma

Open Question

Broken rear sliding window on a 2011 toyota tacoma 4x4 need to replace

I have to use urethane to install how long does it take to cure?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 125 Answers

SOURCE: Can't find the fuel filter on 2004 toyota tacoma 4 cyl 4x4

look under the truck

Posted on May 04, 2009

Ad
  • 10 Answers

SOURCE: Rear Window was broken have a new one, but how do I replace it?

On the interior, there is a rubber lip surrounding the window. This rubber lip holds the glass in place. Here is how to remove without breaking stuff: Collect about 6 sticks (more is better) that are flat and preferabley made of something a little bendable. The ones I use are plastic and measure 8 inches by 1/4 inch by 1 inch and taper down to a blunt, rounded blade at the end.
From the interior, pull back the rubber lip where it meets the cab... not the glass. Where the lip meets the cab, you jam one of the sticks in place so it holds the rubber lip away from the cab of the truck (towards the glass). Start near a corner. About 4 inches away, do this again. Keep doing this until you have all the sticks in place. I found that doing this around one end of the glass (driver or passenger side) allows me to work that end out and the rest will come out with minimal hassle.
To install:
Place window on stand and wrap rubber gasket around window.
Run a string that is about an 1/8 or 3/16 diameter into the groove that grabs the pinchweld of the cab. The string should be long enough to overlap. Overlap by at least a couple of inches. Tape excess string to interior of window.
Have help to jam the bottom of window INTO the cab opening and try to center as best you can.
While applying LIGHT pressure to outside of window, pull one end of string. What you are watching for is that the rubber lip at least catches the cab pinchweld. If you miss this, you will have to start over. (Sometimes you can save it if you have a hook tool handy. A hook tool is essentially a screwdriver bent sharply at a 90 degree angle.)
If you do it right, as you pull the string, it will pull the rubber lip toward the interior of the truck and it will catch the pinchweld of the window opening. A little messaging and slapping of the window will fully seat the glass.
You are done.

Posted on May 10, 2009

ZJLimited
  • 17970 Answers

SOURCE: need to replace a broken window on rear passenger 1999 jeep chero

This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Posted on Sep 09, 2009

  • 37 Answers

SOURCE: replacing front struts on a 2007 toyota tacoma

REALLY HARD PROJECT, TAKE IT TO SEARS, IT WILL ALSO NEED FRONT ALLIGNMENT

Posted on Jul 25, 2010

jturcotte
  • 8273 Answers

SOURCE: need firing order for 2003 toyota tacoma 3.4L V6

3.4L (5VZ-FE) Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system

Thanks for using FixYa.

jturcotte_1309.gif

Posted on Mar 24, 2011

Testimonial: "Well. I'm about to make sure that the firing order is the way jturcotte told me. This is much better information than I have received recently. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DS window on 2011 Toyota Tacoma pickup is not working. Just replaced the 30a fuse & the window stated going down. Now the other windows work, however the drivers window will not go back up. 30


if there is noise coming from the driver side window is down why you pushing the control button for upwards means the window motor / regulator needs to be replaced. If there is nothing the main control switch for the windows may need to be replaced

Jan 12, 2015 | 2011 Toyota Tacoma

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

2 Answers

The rear window to my van came off and shattered during a windstorm... i bought a window off of craigslist.. and can't install it. I dont need it to work,i just need it to go back on.. my bf is taking...


is it a fixed glass or a moveable glass.

Fixed glass is placed against a bead of urethane sealer, like caulking.

Window, Liftgate, Stationary Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: SAFETY GLASSES AND GLOVES MUST BE WORN.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use only urethane for after-seal to service air and water leaks in urethane seal. Failure to do this may result in additional leaks.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Remove window wiper pivot arm (17526) .
  1. Remove all window glass stops.
  1. Using Rotunda Glass Adhesive Cutter 118-00050 or Rotunda Deluxe Glass Adhesive Cutter 163-00001 or equivalent, follow manufacturer's instructions and cut seal and dam around entire outer edge of windshield glass (03100) .
  1. Remove glass from vehicle.
  1. Trim urethane left on flange with a utility knife or razor blade until surface is smooth and free of cuts. It is not necessary to remove all urethane from the flange if it is cured. However, at no point should existing urethane material exceed 2.54mm (0.10 inch). NOTE: If urethane has not cured completely, remove all uncured urethane using care not to smear urethane on component parts.
    Check flange sealing area for damaged sheet metal or foreign objects which may have caused, or may cause, glass breakage. Service sheet metal if necessary.
Installation
  1. If existing urethane on metal flange has become contaminated, cut away contaminated urethane with a utility knife or razor blade.
  1. If painted sheet metal has been exposed anywhere along the flange, apply Urethane Metal Primer WSB-M2G234-C or equivalent over the painted surface using a clean brush. NOTE: A minimum of 30 minutes is required for primer surface to dry.
  1. Place the windshield glass on a low, stable work surface, inside up. NOTE: Wipe off immediately after application because it flash-dries.
  1. Using a lint-free cloth, wipe outer 25mm (1 inch) of inside glass periphery with Urethane Glass Wipe WSB-M5B280-C2 or equivalent.
  1. Position mouldings on glass. ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Thoroughly shake and stir Urethane Glass Primer WSB-M2G314-B or equivalent to ensure uniform pigment mixing.
  1. Using a clean brush, apply primer around entire periphery of glass on inside surface as shown. (Allow at least five minutes drying time.)
  1. Properly align glass to body.
    1. Make sure lower windshield glass stops are in place at bottom of windshield glass opening.
    1. Place windshield glass into opening. Center it top and bottom, side to side, with about equal clearance around opening.
    1. Using masking tape or crayon, make alignment marks at points on both the windshield glass and the window opening.
  1. Remove windshield glass from vehicle and place back on work table.
  1. Apply an even bead of Urethane Adhesive WSB-M2G316-B on top of existing urethane around entire window opening using an air pressure cartridge gun. Air line pressure should be around 276 kPa (40 psi). The bead should be large enough to seal the windshield glass but not cause expulsion into vehicle.
  1. Install windshield glass onto vehicle, taking care to align marks on glass to those on body. This must be done within 10 minutes of applying urethane.


Dec 20, 2010 | 1995 Ford Windstar

1 Answer

How do I replace the back window?


Remove the black vinyl trim from the edge of the glass. Remove broken glass & urethane adhesive from the metal pinchweld leaving a thin layer (approx 1/16") of urethane for new new urethane to adhere to. Vacuum broken glass. Prime nicks to the metal to protect from rusting (also insuring a good surface to bond to). Attach vinyl reveal molding to glass (unless it's a "T" shaped push in type - it would install after the glass is set). Clean and prime the replacement glass. Apply new urethane adhesive. Set glass in place.Slide the metal joint cover in place on the molding (at bottom in the center). Clean outer surface of glass. Allow for safe drive away as noted by urethane manufacturer.

Sep 25, 2009 | 1995 Oldsmobile Cutlass Ciera

3 Answers

2005 vw new beetle convertible back window leaks


I used gorilla glue and it has been holding for over a year now!

Jul 16, 2009 | 2003 Volkswagen New Beetle Convertible

1 Answer

R/H rear quarter window repalcement


tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.
  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

May 29, 2009 | 2004 Ford Focus

2 Answers

Convertible rear window separated from fabric top


This problem is very common and is known as delamination.
Use Urethane adhesive to reglue the window.
This same adhesive is used to install windshields.
The hard part will be to hold the window in place till the Urethane cures.
Prepare for that in advance.

Karl at Topgunwon.com

Mar 20, 2009 | 1997 Toyota Celica

1 Answer

Broken rear slideing glass window on a dodge dakota 2001.


on this truck the rear window is glued in with urethane, if I was cutting it out I would use a special power tool designed to do this. I am sorry but this will not be easy with out it, the only thing I could see is you bending and cut the frame off with a scraper and hammer. (bad picture in my mind) might be worth a stop at an auto glass shop and ask them to remove.

Feb 27, 2009 | 2001 Dodge Dakota

1 Answer

Front axle - front drive shaft Toyota tacoma 1998 4x4


more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Dec 09, 2008 | 2007 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...