Question about 2006 Mazda 3

1 Answer

FUEL RAIL PRESSURE CIRCUIT LOW

SCAN TOOL TELLS FUEL RAIL PRESSURE CIRCUIT LOW

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 50,522 Answers

This report comes from the fuel rail pressure sensor and is advising that the pump is not providing sufficient fuel to keep up the pressure or the pressure regulator is not operating correctly( vacuum line if connected) or the fuel filter is blocked or the tank is not venting correctly. IT may even be the sensor itself is faulty

Posted on Mar 21, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My code on the 2005 ford mustang said that my fuel rail pressure sensor A Circuit


Does the Vehicle start an run ? What engine does it have ? 4.0 or 4.6 L You vehicle has electronic returnless fuel system , Fuel rail pressure sensor , FPDM - fuel pump driver module . The fuel pump driver module controls the fuel by pulse width modulation
Pulsewidthmodulation (PWM) is a powerful technique for controlling analog circuits with a processor's digital outputs. PWM is employed in a wide variety of applications, ranging from measurement and communications to power control and conversion. The PCM - engine computer uses the fuel rail pressure sensor input to send commands to the FPDM .
What code ? P0--- what ?



P0190 - Fuel Rail Pressure (FRP) Sensor Circuit Malfunction Description: The comprehensive component monitor (CCM) monitors the FRP sensor to the powertrain control module (PCM) for VREF voltage. The test fails when the VREF voltage from the PCM drops to a voltage less than a minimum calibrated value. Possible Causes:
  • VREF open in harness.
  • VREF open in sensor.
  • Vacuum leaks.
Diagnostic Aids: Verify a VREF voltage between 4 and 6 volts. Application Key On Engine Off Key On Engine Running Continuous Memory Fuel rail pressure temperature (FRPT) sensor - GO to DD26 GO to DD26 Fuel rail pressure (FRP) sensor only - - GO to DD1 Fuel rail pressure (FRP) and fuel rail temperature (FRT) sensors - - GO to DD1


P0191 - Fuel Rail Pressure (FRP) Sensor Circuit Performance Description: The comprehensive component monitor (CCM) checks the FRP for acceptable fuel pressure. The test fails when the fuel pressure falls below or exceeds a minimum/maximum calibrated value for a calibrated period of time. Possible Causes:
  • High fuel pressure.
  • Low fuel pressure.
  • Damaged FRP sensor.
  • Excessive resistance in the circuit.
  • Vacuum leaks.
  • Low or no fuel.
Diagnostic Aids: A FRP PID value during key on engine running (KOER) of 138 kPa (20 psi) to 413 kPa (60 psi) is acceptable. Application Key On Engine Off Key On Engine Running Continuous Memory Fuel rail pressure temperature (FRPT) sensor GO to DD34 Fuel rail pressure (FRP) sensor only GO to DD9 Fuel rail pressure (FRP) and fuel rail temperature (FRT) sensors GO to DD9


P0192 - Fuel Rail Pressure (FRP) Sensor Circuit Low Input Description: The comprehensive component monitor (CCM) monitors the FRP sensor circuit to the powertrain control module (PCM) for low voltage. If voltage falls below a calibrated limit for a calibrated amount of time during testing, the test fails. Possible Causes:
  • FRP signal shorted to SIG RTN or PWR GND.
  • Damaged FRP sensor.
Diagnostic Aids: A FRP PID value during the key on engine off (KOEO) or key on engine running (KOER) less than 0.3 volt indicates a hard fault. Application Key On Engine Off Key On Engine Running Continuous Memory Fuel rail pressure temperature (FRPT) sensor GO to DD26 GO to DD26 GO to DD39 Fuel rail pressure (FRP) sensor only GO to DD1 GO to DD1 GO to DD14 Fuel rail pressure (FRP) and fuel rail temperature (FRT) sensors GO to DD1 GO to DD1 GO to DD14


P0193 - Fuel Rail Pressure (FRP) Sensor Circuit High Input Description: The comprehensive component monitor (CCM) monitors the FRP sensor circuit to the powertrain control module (PCM) for high voltage. If voltage exceeds a calibrated limit for a calibrated amount of time during testing, the test fails. Possible Causes:
  • FRP signal shorted to VREF or VPWR.
  • FRP signal open.
  • Damaged FRP sensor.
Diagnostic Aids: An FRP signal high condition can be caused by any number of conditions, including a short on FRP signal to VREF, a more positive voltage level, an open FRP signal or signal return. The FRP signal line is pulled up by the PCM and VREF at the sensor, and down by the sensor through SIGRTN. Application Key On Engine Off Key On Engine Running Continuous Memory Fuel rail pressure temperature (FRPT) sensor GO to DD26 GO to DD26 GO to DD39 Fuel rail pressure (FRP) sensor only GO to DD1 GO to DD1 GO to DD14 Fuel rail pressure (FRP) and fuel rail temperature (FRT) sensors
P1233 Ford Fuel Pump Driver Module Diagnostics and Repair

FPDM Live

Jan 14, 2018 | Ford Cars & Trucks

1 Answer

My 2007 Toyota isis iaz.read code P0191


Anon, Trouble code P0191, You may need a good tech. with scan tool to read and test system.
  • Fuel Rail Pressure Sensor Circuit Range/Performance,computer see's signal from the Fuel Rail Pressure Sensor and/or its circuit is sending erratic readings, indicating a fuel pressure condition that is abnormal. Problems could be out of gas, leaking fuel, faulty fuel pressure sensor, bad wire or plug in circuit,fuel pressure regulator, the fuel pump could be faulty also. Check the attached links,instruction and guides, Good luck
    "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
P0191 OBD II Trouble Code

P0191 Fuel Rail Pressure Sensor Circuit Range Performance

RAV4 2001 Trouble Code p0191 probable solution Toyota Nation Forum Toyota...

code P0191 2007 Toyota Google Search

May 03, 2016 | Toyota Cars & Trucks

1 Answer

Fuel rail pressure sensor high voltage. P0193


Possible causes
- Low or no fuel
- Faulty Fuel Rail Pressure Sensor
- Fuel Rail Pressure Sensor harness is open or shorted
- Fuel Rail Pressure Sensor circuit poor electrical connection
- Faulty Fuel Pump

Mar 28, 2015 | Cars & Trucks

1 Answer

08 Chevy Kodiak c4500 duramax desiel i replaced the MAF sensor because the code reader said P0102 now it says P0087 that is the problem but everytime I'm hauling something the engine always decreases its...


DTC P0087: Fuel Rail Pressure (FRP) Too Low

Circuit/System Description
The fuel injection pump supplies high pressure fuel to the fuel injection rails, and then to the fuel injectors through high pressure pipes. The fuel rail pressure (FRP) sensor is a three wire sensor mounted in the right fuel injection rail. The FRP sensor uses a 5-volt reference circuit , a signal circuit, and a low reference circuit to monitor fuel rail pressure. This information is sent to the engine control module (ECM) to assist in the fueling of the engine.

Fuel Pressure Regulator Solenoid Supply Voltage
P0088, P0090
P0088
P0090
P0087, P0191, P2510
Conditions for Setting the DTC
P0087
• The actual FRP is more than 15 MPa (2,176 psi) below the desired FRP.
OR
• The actual FRP is less than 22.5 MPa (3,263 psi).

Action Taken When the DTC Sets
• DTCs P0087 and P0088 are Type A DTCs.
• The ECM commands the engine to operate in the Reduced Engine Power mode.
• The message center displays Reduced Engine Power.

Important: Because of the cleansing properties of the biodiesel, switching from the straight diesel to a biodiesel blend can prematurely restrict the fuel filter with normal deposits in the fuel system. A fuel filter replacement might be required sooner than the recommended interval.
P0087
If DTC P0090, P0168 or P0191 is also set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
Ignition ON for 90 seconds, verify the scan tool FRP Regulator Command parameter is less than 20 percent.
? If greater than the specified range, replace the ECM.
Attempt to start the engine.
? If the engine does not start, refer to Engine Cranks But Does Not Run.
Install the CH-48027 to the fuel rail service port and slowly increase the engine speed until reaching wide open throttle (WOT). The value should be between 1-4 inches Hg vacuum.
? If more than the specified value, inspect for restricted fuel filter or damaged supply lines.
? If no restriction was found, test for high fuel return flow. Refer to Fuel System Diagnosis - High Pressure Side.
With the engine idling or at an idle, command the fuel pressure control to 180 MPa (26,106 psi) with a scan tool. Observe the Actual Fuel Rail Pressure parameter. The actual fuel pressure should be the same as the commanded pressure.
? If the Actual Fuel Rail Pressure is less than 165 MPa (23,931 psi), refer to Fuel System Diagnosis - High Pressure Side.
Important: If the fuel temperature is near 121°C (250°F) during the duplication of the complaint, or in the Failure Records for this DTC, inspect for a restriction in the fuel cooler air flow or the fuel heater always ON. Refer to Fuel Heater Always On.
Operate the vehicle within the conditions for which the customer complaint occurs while observing the CH-48027 . You may also operate the vehicle within the conditions that you observed in the Freeze Frame/Failure Records.
? If the vacuum was more than 12 inches Hg of vacuum at any time in the operating range, inspect for kinked or restricted fuel supply lines.
Operate the vehicle within the conditions for which the customer complaint occurred. Observe the Actual fuel Rail Pressure and Desired Fuel rail Pressure parameters with a scan tool. Fuel pressures should be the same for both parameters.
? If the Actual Fuel Rail Pressure is less than the Desired Fuel Rail Pressure, refer to Fuel System Diagnosis - High Pressure Side.
? If fuel system tests normal, refer to Diagnostic Aids.

Aug 20, 2017 | Cars & Trucks

1 Answer

I previously posted my 2005 Ford Escape Hybrid had a code P0190 . I bought a scan tool and actually have two codes (P0191 and P1237).


p1237
- Fuel Pump Secondary Circuit (Fuel Pump Driver Module)
p0191
- Low or no fuel
- High fuel pressure
- Low fuel pressure
- Faulty Rail Pressure (FRP) Sensor
- FRP harness is open or shorted
- FRP circuit poor electrical connection
- Faulty Fuel Pump
- Vacuum leaks

Apr 25, 2014 | Cars & Trucks

1 Answer

P0192


P0192 - Fuel Rail Pressure Sensor Circuit Low Input

Possible causes- Excessive resistance in the circuit
- Low or no fuel
- Wiring harness connector of the fuel pressure sensor
- Fuel Rail Pressure Sensor
- Fuel Pump or fuel pump relay defective. I think this is the problem.

Oct 12, 2012 | Cars & Trucks

1 Answer

2002 taurus code po191


That is P0191 not o.
P0191 FORD - Fuel Rail Pressure Sensor Circuit Range/Performance

Possible causes- High fuel pressure
- Low fuel pressure
- Damaged FRP sensor
- Excessive resistance in the circuit
- Low or no fuel
- Wiring harness connector of the fuel pressure sensor
- Fuel Rail Pressure Sensor
-

Oct 05, 2012 | 2002 Ford Taurus

2 Answers

Code p0191


P0191 FORD - Fuel Rail Pressure Sensor Circuit Range/Performancexicon.jpghttp://engine-codes.com/p0191_ford.htmlForum CodePossible causes- High fuel pressure
- Low fuel pressure
- Damaged FRP sensor
- Excessive resistance in the circuit
- Low or no fuel
- Wiring harness connector of the fuel pressure sensor
- Fuel Rail Pressure Sensor
- Fuel
- Vacuum leaks

Jul 04, 2012 | 2003 Ford Taurus

1 Answer

Hur byter jag växellädsolja på


160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition

P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

P0178....Fuel Composition Sensor Circuit Low Input

P0179....Fuel Composition Sensor Circuit High Input

P0180....Fuel Temperature Sensor A Circuit

P0181....Fuel Temperature Sensor A Circuit Range/Performance

P0182....Fuel Temperature Sensor A Circuit Low Input

P0183....Fuel Temperature Sensor A Circuit High Input

P0184....Fuel Temperature Sensor A Circuit Intermittent

P0185....Fuel Temperature Sensor B Circuit

P0186....Fuel Temperature Sensor B Circuit Range/Performance

P0187....Fuel Temperature Sensor B Circuit Low Input

P0188....Fuel Temperature Sensor B Circuit High Input

P0189....Fuel Temperature Sensor B Circuit Intermittent

P0190....Fuel Rail Pressure Sensor Circuit

P0191....Fuel Rail Pressure Sensor Circuit Range/Performance

P0192....Fuel Rail Pressure Sensor Circuit Low In put

P0193....Fuel Rail Pressure Sensor Circuit High Input

P0194....Fuel Rail Pressure Sensor Circuit Intermittent

P0195....Engine Oil Temperature Sensor

P0196....Engine Oil Temperature Sensor Range/Performance

Nov 20, 2010 | 2004 Volvo S80

Not finding what you are looking for?
2006 Mazda 3 Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...