Question about 1994 Isuzu Pickup

1 Answer

94 isuzu pickup engine number location

I need to kwnow where is located the engine numbr in lw3 engine, because I finded it out and anything

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 76,164 Answers

Under the intake on the block on most models.

Posted on Mar 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
shaggyrat
  • 1224 Answers

SOURCE: isuzu trooper engine numbers

ok there are several places to look
the door panels stickers
the glove box
the engine compartment
manual
the engine number will be stamped on the block if facing truck it would be on the bottom right hand side between the first and second freeze plug

Posted on Jun 02, 2008

  • 1 Answer

SOURCE: ISUZU RODEO SPARKS PLUGS CHANGE OVER

In the center of each valvecover is a well with a wire in it each wire has a seal cap attached pull up and youll find a stem which goes down a tube this is part of the spark plug wire the plugs are at the bottom of this tube youll need a long adapter on your wrench and socket for this job and you can extract the plug using the wires stem

Posted on Aug 04, 2008

djicenova
  • 319 Answers

SOURCE: where is air cabin filter located on 99 isuzu rodeo?

its usually behind the glove compartment in the blower box. you will have to pull the GB door down all the way to access it

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: Please I need your help

I need a part for my Scotts/John Deere tractor-blade starter-black rubber with 8 prongs and yellow knob. Yellow knob has sun symbal on top. The back of the switch has Delta Systems, Inc. Series 6201 Pat No. 5221816 -also has KSD on the side Com C Com B and Com A on other side. Please advise whee I can find this part.

Posted on May 25, 2009

  • 16 Answers

SOURCE: can't find location of the transmission fluid dip stick ...

It has to be checked by the service center by raising the vehicle and removing the bolts as in replacing the transmission fluid. This was on the 97-99's. They have gone back to dipsticks but unfortunately we are stuck with the service center.

YES you can do it!! Be careful not to overfill but do as follows to check the fluid. As you don't have an ATF dipstick, you will have two plugs facing down on the trans pan. The plug higher up on the pan is the fill/level check (stamped/recessed into the rear right corner of pan). ATF should just drip from this plug on a hot, idling truck, in neutral on a flat surface. The lower one is the drain. The one at the back of the pan in a recess is the filler. You need a squirt pump or something like one to fill it with the engine running.

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump location 94 izusu pick up 2.6 leter


there has been a mistake,that was not my car.my car is the hhr that had the engine light on.

Jun 29, 2014 | 1994 Isuzu Pickup

1 Answer

Need to locate where turn signal flasher is in 1988 isuzu pick up


FLASHER

1988 Isuzu Truck Truck 2WD 2.3L 2BL 4cyl

The Flasher is located: Front seating area, driver side, under dash, near fuse panel, taped to dash wiring harness

If you still can't find it turn the signal on and listen for it.

Feb 12, 2013 | 1988 Isuzu Pickup 2WD

1 Answer

My isuzu dmax oil pan had a dent giving only 2mm space between the pan and the oil pump end tube. does it impair its suction power assuming the pump is in excellent condition. what psi does an isuzu dmax...


In order for that dent to have any real effect upon oil delivery, the dent would need to be perfectly flat up against the oil pump pickup. Chances are it isn't. The pickup in most pans is located a bit above the pan bottom to lessen the chance of ingesting any contaminants (sand, grit, hard carbon etc). With the clearance diminished, chances of that are greater.
While only oil pressure is measured, volume is also important. With the pan that close to the pickup, pressure probably won't be a problem but you may loose some volume (impossible to tell how much).
When I put together a fresh engine, I like to see pressure of about 40psi or better. As an engine wears, engineers claim that anything above 15psi is OK...I use a higher number of 25psi (at idle) as a minimum "safe" limit. Anything below that, you know you have a problem and it's wise to find it early and fix it. (Pumps rarely fail...most low pressure problems can be traced to engine bearing wear, resulting in bleed off past the bearings)
As for your pan: If the pan is bent, and you have it off the engine, why not hammer the bend out a little? or, better yet, get another pan from a scrapyard and replace it entirely?
If you have not removed it, there's no real way of measuring and what you are seeing may not be the whole story...pickup clearance may be greater elsewhere. In that case, just continue doing regular service and save pan replacement for a day when you have time to do it.

Mar 30, 2011 | Isuzu Pickup Cars & Trucks

2 Answers

94 izuzu pickup engine options


There are 3 options with engine codes after the size.
2.3L -LW3
2.6L -4ZE1
3.1L -Z

Feb 14, 2011 | 1994 Isuzu Pickup

1 Answer

Where is the fuel filter located on a 1990 Isuzu pickup with 2.3 liter engine.


The filter is located on the frame rail by the passenger side rear wheel.

Oct 15, 2009 | 1990 Isuzu Pickup

1 Answer

Where is the starter relay on 94 isuzu pickup 4wd standard transmission?


In the under hood fuse and relay box. The cover of the box should be marked to show the location

Oct 12, 2009 | 1987 Isuzu Pickup

1 Answer

'94 Isuzu pu (carb.) Sometimes dies while running down freeway


Check all the old ' brittle plastic vacume line connections .And the idle control valve unit located near the passenger side firewall. Over the front wheel cover. passenger side.over.

Feb 12, 2009 | 1993 Isuzu Pickup

1 Answer

Were is the temperature sensor located on an 87 isuzu pup


Temp sensor is located on the intake manifold near the front of the engine by the distributor. It is threaded upsidedown and the dist. will have to be moved out of thw way to access it.

Jan 03, 2009 | 1987 Isuzu Pickup

1 Answer

Swapping motors


my 88 isuzu pick up 2wd. LW3 engine? mine needs rings and a valve job and a I think a new head gasket.

Jul 07, 2008 | 1988 Isuzu Pickup 2WD

Not finding what you are looking for?
1994 Isuzu Pickup Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...