Question about 2002 Ford SVT Focus

Open Question

St170 clutch problem

Won't go into gear

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission won't ingage


Sounds Like Pressure Plate Or Clutch Plate Are Worn Out ,You Could Check The Slave Cylinder To See That It Is Going Full Travel In And Out As You Operate The Clutch Pedal

Mar 29, 2013 | 1988 Isuzu Trooper 2 Door

1 Answer

My clutch is soft in my 2000 ford focus . It won't


bleed the air out of the clutch system

Jul 23, 2017 | Cars & Trucks

1 Answer

Manual trans won,t shift 87f150


When there is an issue with a manual gear box not working after a clutch replacement I am always suspicious that the clutch plate has been fitted the wrong way and the crank bolts are fowling on the cluch plate center . If the gear box was fine before and i now faulty I would go to what was done with the clutch. Also check that the clutck slave cylinder is working ok.

Feb 22, 2013 | 1987 Ford F 150

1 Answer

My clutch won't go down and won't go into any


ABS light coming on,For this get the Engine computer scanned.It can be error codes stored in computer.------------
For more details regarding this click the link below:-----
The ABS and Traction Control Lights stays ON dash of car? http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

---------------
And now for clutch not going in gears it can be faulty clutch issue or problem with clutch cable.This has to be inspected.For more detailed instructions regarding Peugeot clutch problem,click the link below:-----
Peugeot 307: Clutch will no go in gears?
http://whoisbyme.blogspot.in/2012/05/peugeot-307-clutch-will-no-go-in-gears.html

---------
This will help.
Thanks.

May 30, 2012 | 2004 Peugeot 307 SW

1 Answer

My 1998 Honda civic ex won't move but the motor


Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

1 Answer

WHen under load the motor revs up and it seems that the Clutch is slipping, it has 100000miles and I suspecting the clutch or the high / low range might be messed up, its a 4 plus 3 manuel transmission.


If it feels like the clutch is slipping, chances are it is. If there was a problem in any component that has internal gears, you would have grinding noises. Gears cannot slip. As the clutch wears more you may hear grinding when you try to change gears but that is because the clutch won't fully disengage so the gears are spinning too fast to shift properly. Before that happens, have the clutch replaced.

Aug 02, 2011 | Chevrolet Corvette Cars & Trucks

Not finding what you are looking for?
2002 Ford SVT Focus Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...