Question about Audi A4

1 Answer

2003 Audi A6 1.9 tdi: where do I find the onboard computer?

The computer has ceased to function. I need to locate its position in the vehicle.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 48 Answers

It will be in the plenum area (between windscreen and firewall under bonnet (hood)).
Look for a black plastic box held down by several screws.
On my A4 (1997) it was on the drivers side. On my S8 (2001) it's on the passenger side. A6 I don't know, but it will be obvious.

Posted on Nov 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

3dmaster
  • 183 Answers

SOURCE: audi gearbox romovel and refit

Dear Customer,

you have to do with your service manuals like how much transmision ratio your car can accept or drive easily,

that tranmision you have to install in & use as super car you drive.

new audi transmision fitting is almost same as you remove if acceptable kit you are goin to install.

THNX


Posted on May 16, 2008

TLRogue
  • 99 Answers

SOURCE: temperature sensor audi a4

Possibly located at the back of the engine behind cylinder head, usually located in a small plastic hose block.

TL

Posted on Jan 23, 2009

REDOIL
  • 355 Answers

SOURCE: Location of oil filter on a VW 1.9 TDI passat 2003

WELL THAT YEAR DOSE NOT COME WITH 1.9 BUT ANY WAY IT SHOULD BE UNDER CAR NEAR RIGHT AXLE OR LEFT SOME TIMES

Posted on Aug 31, 2009

  • 114 Answers

SOURCE: where is the crankshaft position sensor locator on a 2003 audi a4

The crank position sensor is located on the forward front of the engine block, on the left side, down low by the crank pulley

Posted on Sep 19, 2009

  • 1596 Answers

SOURCE: the function that rsiaes and lowers the vehicle doesn't work,

Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find diagnostic plug for my audi a6 1.9 tdi 52 plate


LOCATED NEAR HOOD RELEASE HANDLE WAY TOWARDS THE FOOTREST!!ITS A LITTLE BIT HIDEN!!

Jan 28, 2014 | 2003 Audi A6

1 Answer

Reverse lights switch location on Audi A4 1.9 tdi 2003 model 6 speed, can you help please


The switch for reversing light is placed on the right side of the gearbox for Audi 1.9 TDI 2003 model 6 speed.
Switch: M14 x 1,5 & Part number: 01E941521A.
See picture below:

tdisline_166.jpg
Please do rate my response. Thanks!

Jan 20, 2011 | 2005 Audi A4

1 Answer

Where is the location for the fuel pump relay in a 2007 a3 2L tdi 170bhp


The fuel lift pump relay is placed in the fuse box / relay plate fascia 2 for 2007 Audi A3 2.0 TDI. The fuse box / relay plate fascia 2 is placed above pedals behind a plastic cover. See pictures below:

The fuse box / relay plate fascia 2
tdisline_152.jpg

The fuel lift pump relay
tdisline_153.jpg
The fuel lift pump relay is placed in "2b" position in the above picture.


Please do rate my response. Thanks!

Jan 07, 2011 | Audi A3 Cars & Trucks

1 Answer

HI I HAVE A 2003 AUDI A4 1.9 TDI I RESET MY SERVICE INDICATOR BUT NOW THERE ARE JUST DASHES WHERE AS BEFORE IT TOLD ME HOW MANY MILES OR DAYS UNTILL NEXT SERVICE HOW DO I SOLVE THIS


On 2003 Audi A4 1.9 TDI the "SERVICE" message can be reseted only using: VAS, VAG-COM, Bosch KTS, Texa, ... diagnostic scantool. Not possible without this equipment connected to the data link connector (DLC) of the car !

Dec 06, 2010 | Audi A4 Cars & Trucks

1 Answer

Which oil I should use for Audi A6 2.5 TDI


all AUDI/VW use 5/40 full synthetic when new,but in Europe,use 10/40 semi for 10k oil changes and 5/40 for 20k services.the computer onboard,when set correctly,will give you the change intervals.these are set by the supplying dealer when new,and only by putting on the (VW) diagnostic computer,will it give these intervals. otherwise your just guessing....(most new cars for the USA market are set to "extended"servicing regime,so use 5/40 full).

Nov 21, 2010 | 2004 Audi A6

1 Answer

Hi, I have audi a4 model 2003 1.9 tdi 130 pk and before two days on my board computer I saw message ,, Service in 2400 km 29 tagen ,, and I looked at my audi guide, but I didn't found what is mean ,, 29...


For Audi A4 model 2003 1.9 TDI 131 HP the board computer message ,,Service in 2400 km 29 tagen" means: Service due in 2400 km, or in 29 days - which one: 2400 km or 29 days will be first covered. It's very simple!

Oct 16, 2010 | 2002 Audi A4

1 Answer

Audi A4 1.9 TDI power steering oil type and capacity


Power steering fluid level checking:
- vehicle stationary
- front wheels in straight ahead position
- engine at normal operating temperature
- remove cap with dipstick from expansion tank and wipe off
- reinstall cap with dipstick and remove again
- fluid level between "min" and "max" markings
- top off with G 002 000 hydraulic oil if necessary
Power steering system capacity is around 1 liter, but it is not necessary to periodic change the hydraulic oil!
If oil level has dropped to the "min" marking, check power steering system, including hoses and lines.
It is not enough simply to top off the hydraulic oil !!!

Oct 02, 2009 | 2003 Audi A4 Cabriolet

1 Answer

Audi flywheel - 1.9 tdi


you can use one off a vw passat

Aug 19, 2009 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...