Question about 2005 Chrysler PT Cruiser

Open Question

New fuel pump need to bleed line

Air in fuel line

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

60 horse Work Master New Holland wont start blead lines but looses fuel to filter seems like hand pump dont work will run if you spray ether then dies when you stop spraying it. Can someone help


Earl You have to be able to bleed all of the air out of the fuel filter and lines for your engine to run. If the fuel is leaking back to the tank there is a problem with the valves in the hand primer pump.You might have to replace the pump. Remove or loosen the bleed screw on the top of the filter and pump out all of the air so there is no more bubbles then loosen the fuel lines at the injectors and turn the engine over with the starter to bleed the lines. Only crank over with the starter for 30 seconds per try and give the starter time to cool down

Oct 31, 2015 | Cars & Trucks

1 Answer

New fuel pump and filter. Fuel line has air lock. Blew out lines.


the easiest way to bleed the entire system will be in the service manual for your vehicle. Aslong as your fuel pump is not airlocked it should be fairly straightforward to bleed it.

Sep 20, 2015 | Cars & Trucks

1 Answer

Why fuel does not go through pump? Toyota rav 4 d4d engine


1 Blocked fuel filter = fit new filter and bleed fuel lines
2 Air in fuel lines = check fuel lines for cracks, repair and bleed fuel lines
3 No fuel = fuel car, bleed fuel lines

Dec 29, 2014 | Toyota Cars & Trucks

1 Answer

Bleed fuel lines


you do not need to bleed the fuel lines . turn the key on for 30 sec then off do this several times and the pump should prime the sys . if not , you might have a fuel pump problem

Mar 04, 2014 | 2001 Volkswagen Golf

1 Answer

My Pontiac Sunbird 96 ran out of fuel. I need to know how to bleed the system of air. Where is the bleeding line??


you shouldn't need to bleed the air out-if you filled back up with fuel and its not starting you probably have a bad fuel pump-sorry- to bleed the fuel line look where the fuel line connects to the fuel injector rail-on the rail there should be a thing that looks like a tire inflator valve-turn the key on and push in the center of the valve and fuel should come out of it -if not then for sure pump isn't working- cheers Denny

Nov 27, 2013 | Cars & Trucks

2 Answers

My 5.9 dodge cummins diesel won't start, I've replaced the fuel lift pump, and the fuel filter, turns over. But will not start?


Most likely you just have air in the lines.Crack them open one at a time and bleed them with the fuel pump off and on till you get fuel.If it fires dont hit the throttle let it sit and idle and close the line.Does it fire up with a small whif of starting fluid?

Mar 17, 2013 | 1999 Dodge Ram

1 Answer

Replaced fuel pump and cant get fuel lines to prime


There is no priming to do

If the injectors are working, any air
in the lines comes out into the cylinders,
then the fuel & your good to go

The fuel pump will push out any air with the fuel

Does the pump come on for 3 seconds with key on?

Do you have fuel pressure on a gauge at the motor?
You can push the button on the gauge to bleed off your air

Jan 23, 2013 | 1999 Toyota RAV4

1 Answer

1994 vw gulf has air in the fuel line,how to get it out?


Loosen the fuel line at the injector pump and crank the engine to push them out. You may need to loosen the lines at the injectors as well to push it all out. (I've had to bleed a number of diesels of all sizes) However, the other question is how did it get in there? If you ran out of fuel and need to bleed it out, fine. If not, an air bubbles are continuously showing up in the fuel line, you may have a suction side leak (a leak before the primary fuel pump that is sucking air in)

Nov 25, 2009 | 1994 Volkswagen Golf

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...