Question about 2010 Chevrolet Cruze 1.6

Open Question

Code 26 and brake signal displayed

What mean code 26 and brake signal displayed

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have code p0573 saying brake switch A is high although brake lights are working ok, can anyone help please


Possible causes
- Faulty Brake Switch
- Brake Switch harness is open or shorted
- Brake Switch circuit poor electrical connection
help.jpg What does this mean? When is the code detected?
The P0573 codes is set when the stop light switch signal is too high.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Stop light inoperative
- Cruise control system inoperative
P0573 Description
When the brake pedal is depressed, the stop light switch sends a signal to the Engine Control Module (ECM). When the ECM receives this signal, it cancels the cruise control.

Aug 29, 2014 | Cars & Trucks

1 Answer

Engine light code c121c ?


Will code c121c case your car to just stop while driving.

May 01, 2014 | 2007 Dodge Charger SRT8 Sedan

1 Answer

Code 26


http://www.cruzeblog.com/cruze-error-code/ this might help

Mar 20, 2014 | 2010 Chevrolet Cruze 1.6

1 Answer

Fuel fail code 26


http://www.heavydutypowertrain.com/md200codes.pdf
i dont know if is the same

Externally Supplied Voltage at of the following: Fuel Shutoff Valve, Fan Clutch,
Engine Brake

Jun 27, 2012 | 1992 Jaguar XJ6

1 Answer

My '93 suzuki sidekick automatic transmission 4 wheel drive after warm up "overdrive off" starts flashing on and off and when on the drivetrain stops working


The O/D light's flashing means there is some kind of transmission trouble.

The codes are..


Trouble Code (1) Probable Cause
12 ............................... System Operation Normal
21 ..................... No. 1 Shift Solenoid Open Circuit
22 .................... No. 1 Shift Solenoid Short Circuit
23 ..................... No. 2 Shift Solenoid Open Circuit
24 .................... No. 2 Shift Solenoid Short Circuit
25 ............................. TCC Solenoid Open Circuit
26 ............................ TCC Solenoid Short Circuit
31 ............ Vehicle Speed Sensor Open Or Short Circuit
32 ................ Throttle Position Sensor Short Circuit
33 ................. Throttle Position Sensor Open Circuit
34 ................ Defective Park/Neutral Position Switch
36 .............. (2) No Signal-Both Vehicle Speed Sensors
(1) - Check listed component for probable cause. Also check wiring and connections of specified component.
(2) - No signal from both transmission and speedometer mounted vehicle speed sensors.

If a trouble code is present, OD OFF light will flash a trouble code. The number of flashes will equal first digit of trouble code. After a one second pause, second digit will be displayed. If more than one trouble code is present, next trouble code will be displayed after a 3 second pause. Smallest number trouble code will be displayed first. Trouble codes will be repeated.

Hope this gave you some insight on the issue.

Mar 08, 2011 | 1993 Suzuki Sidekick

1 Answer

1995 Dodge Stratus Error codes 12, 13, 14, 24, 26, and 33. What do each of these mean?


Code 12 is only displayed when outputting "flash codes" (Cycling the key and watching the Check Engine Light flash) - it mostly indicates that the diagnostic system is functioning properly. There is only a problem if you don't get this code.

Codes 13 and 14 are both MAP Sensor codes.

Codes 24 and 26 are both Secondary Air Switching Solenoid codes.

Code 33 is an A/C Presure sensor circuit code.

Flash codes are pretty generic. They tell you that there is a failure in a particular system, but they don't specify what type of failure. Flash Code 14 for example, can mean that the Map Sensor Voltage is too high or it can mean that it is too low, or it can mean that the 5 volt reference voltage is shorted to ground.

"P-codes" (The kind you must have a scanner to get) however, are more descriptive. Those will give you a more accurate description of what exactly is the problem with the system that has failed.

I will advise you however, that all of these codes can be caused by a shorted VREF. (5 Volt Reference Circuit) Find out where it is shorted and you will most likely fix all of these codes with one repair.

Dec 04, 2010 | 1995 Dodge Stratus

1 Answer

What does code 26 mean?


Did you try going to Advance Auto or a similar business to check the code for that. Sometimes they can get you in the ballpark or check error codes online.

Jun 07, 2010 | 1990 Buick Riviera

1 Answer

I have a 1994 Toyota 4Runner with a V6 and the check engine light came on i jumped the terminals and code 14 and 26 came up. what does the codes mean?


These are the codes and possible causes taken from http://www.off-road.com/toyota/tech/codes/
Code 14 :
IGNITION SIGNAL--NO "IGF" SIGNAL TO ECU
--IGNITER/IGNITER CIRCUIT
--IGNITER AND IGNITION COIL/CIRCUIT
--ECU

Code 26 :
AIR/FUEL RATIO RICH INDICATOR
--INJECTOR FAULT(S)
--FUEL PRESSURE
--OXYGEN SENSOR
--AIRFLOW METER OR MAP SENSOR
--IGNITION
--ECU
--COLD START INJECTOR

Sep 17, 2009 | 1994 Toyota 4Runner

Not finding what you are looking for?
2010 Chevrolet Cruze 1.6 Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...