Question about 2005 Ford Focus

1 Answer

How do I replace a blend door actuator on a 2007 ford focus

Replace blend door actuator

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 103 Answers

Posted on Mar 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 30 Answers

SOURCE: where is the blend door actuator in a 2000 ford

look behind the glove box area to the left square motor

Posted on Mar 11, 2009

harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

roniecon
  • 6826 Answers

SOURCE: need to locate blend door actuator on 2002 ford

Open the glove box,and look on top of ac/heater box toward the center of vehicle,it should be setting right there.

Posted on Oct 10, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

bunnydawg
  • 5158 Answers

SOURCE: 2002 Ford Crown Vic 4.6L. EATCM A/C, Heating

that clicking noise you hear is likely a relay in the fuse panel that needs to be replaced. the easiest way to find out which relay it is would be to put you finger on each relay as you actuate the device not working. once you locate the clicking relay replace it . to reset the computer just unhook the battery for about ten minutes. if you have an anti theft radio make sure you know the code for it and how to enter it before you unhook the battery.

robert

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

Trying to figure out the required positioning of the blend doors in a 2007 dodge dakota


Does it have an electric control actuator ? An it's mode door not blend door . Mode door controls where air comes out of , defroster , vent , floor etc... an the blend door controls the temp. Pull the mode door actuator an see if the door move's freely , not binding . After replacing an evaporator if everything was put back right you shouldn't have this kind of problem . There is no relearn for the door actuator . Double check your work is the best answer anyone could give !

Jul 30, 2016 | 2007 Dodge Dakota Quad

1 Answer

Blend door actuator is there a fuse or relay


No there is not a fuse that JUST runs the blend door actuator. You likely have a jammed blend door and that destroys the little gear drive in the actuator motor. Good luck.

May 17, 2016 | 2007 Ford Freestar Limited Minivan

2 Answers

Air blend actuator 2000 ford explorer is not working?


First, insure you do not have a vacuum leak or bad vacuum check valve. If this is all good, you may have to change actuator and every model has a different way to access this--some require dash removal. If you must do this, get a shop manual as the air bags CAN BE VERY DANGEROUS!

Mar 28, 2016 | 2000 Ford Explorer Eddie Bauer

1 Answer

Location of blend door actuator,2007 ford tauris


Drivers side, under the dash, to the right of the gas pedal. If you have dual control there is one on the passenger side also.

May 10, 2015 | 2007 Ford Taurus

1 Answer

Top blend door actuator on 2011 f150


You need to google 2001 f150 blend door actuator replacement. It is slightly right of center above the plastic duct work for the floor area. All lower dashboard plastic is removed to get at it.
Then the ducting is removed.
http://www.autozone.com/repairguides/Ford-Pick-Ups-Expedition-Navigator-1997-2000/Heating-and-Air-Conditioning/Blend-Door-Actuator/_/P-0900c152801e55ed

Feb 17, 2014 | Ford Freestar Cars & Trucks

1 Answer

Hot air not working


Air Temperature Control Blend Door Failure

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car.



Oct 30, 2012 | 2000 Ford Focus

1 Answer

I have a 2007 ford explorer, all of a sudden, the ac blows only through the defroster,and at my feet. It will not blow through the front vents. The ac blows cold.


the blend door actuator is bad. there about 70 dollars at ford. make sure you hook up the actuator and put the control on defrost before you bolt it on the air box or you will brake the blend door.

Jul 19, 2010 | 2007 Ford Explorer Eddie Bauer

Not finding what you are looking for?
2005 Ford Focus Logo

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...