Question about 1999 Mitsubishi Eclipse

Open Question

Codes po340 Put new motor in and a new cam position sensor and still getting the same codes and my tack quit working

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code po340,change coil,cam sensor,still got code,missing


that is the code for cam position. . when you replaces the sensor did you clean the cam,and replace the seal. what motor do you have

Dec 09, 2012 | 1996 Chrysler Town & Country

1 Answer

2003 Hyundai Santa Fe Still Will Not Start PO320 PO340


code p 0320 refers to crank shaft position sensor (CKP)/engine speed (RPM ) sensor---circuit malfunction====causes ---wiring---CKP/RPM sensor ---ECM
code p 0340 refers to camshaft position sensor (CMP) sensor A bank 1---circuit malfunction===causes wiring---CMP sensor ---ECM
following engine work , it is always best to check that all of the harness connections were assemble properly
check for broken wires during the work

Apr 29, 2017 | 2003 Hyundai Santa Fe

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

I own a 2004 accent with 122,000 km on it. Long story short, had to get a new head gasket put on, so rocker cover, cams, everything had to come off. Work was done and everything was put back together. I...


P0340 - Cam Timing

SYMPTOMS/CONDITIONS
of a mistimed camshaft system (all must apply):
  1. Camshafts have previously been removed from the engine.
  2. Engine runs rough.
  3. Vehicle sets P0340 (camshaft sensor code).
  4. Camshaft sensor has been checked with a known, properly operating camshaft sensor.

CORRECT:
The diagram in the manuals should show the timing marks on both cam gears to be on the blue timing chain links.

ghost45_11.jpg

Mar 23, 2011 | Hyundai Motor 2004 Accent

1 Answer

HELLO, I HAVE TROUBLE CODES PO330,PO340, ON MY OBD2 READER WITH THE MAINT LIGHT ON IN 96 BMW Z3 ROADSTER 4CYL., PO330 IS KNOCK SENOR, PO340 IS CAMSHAFT POSITION SENOR, I WANT TO KNOW HOW TO FIX THEM BOTH....


The Cam Position Sensor is a common item to fail. However, the cam positioning mechanism can fail too giving that code.

There are two sensors and the Exhaust Cam Sensor is most common to fail. I always replace both.
Te CKP's are on the top front of the engine next to the cylindrical operation solenoids.

Knock sensors fail too and need checked or correct feedback to ECU with a scanner.
Find a shop near you at http://www.iatn.net/shopfinder/

These engines require regular oil changes with quality synthetic oils and OE filter....not a FRAM or WIX !

Buy only BMW sensors ...aftermarket have high failure rate.

Jan 12, 2011 | 1996 BMW Z3 Roadster

1 Answer

Code po340 says camshaft position sensor circuit malfunction


replace the cam shaft positioning sensor. this is not a big job
the sensor is usually on front of block above the crankshaft pulley wheel
to change involves disconecting wire from sensor. remove bolt remove sensor,intall new sensor, replace bolt.re connect wire

Dec 14, 2010 | Dodge Caravan Cars & Trucks

1 Answer

Code po340 2002 p/t cruser


you can do 1of two things 1pull the cam sensor out and clean it up and reinstall it to see if that works or you can replace it with a New one, this is what the code po340 means that you have a problem with the cam sensor

Dec 01, 2010 | Chrysler PT Cruiser Cars & Trucks

2 Answers

DTC - PO340, PO325


My Nissan micro 2004 model just stopped in the middle of the road one day then the engine management light came on, anyway took it to my local garage TWK Thomas who said it was a cam shaft sensor problem. OK so sensor was put on, engine management light went off for two days only. So went back to the garage they said that another sensor should be fitted on the opposite side. And then the problem should be rectified, but i had given the £160 for this problem to be fixed the first time. I decided it was time to take it to another garage Nis Tec they put it on the computer and a code po340 came up would this mean another sensor or the cam chain has stretched please help. ...claire

Jul 09, 2009 | 1998 Nissan Maxima

Not finding what you are looking for?
1999 Mitsubishi Eclipse Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...