Question about 2008 Lincoln Town Car

1 Answer

Need to reconnect exhaust

I bought this car and now I find outthe exhaust is disconnected

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 74,945 Answers

What is disconnected.

Posted on Mar 21, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to find my starter for a 1997 Acura RL


It is under the car at the rear. Here is the procedure to remove it.
Removal

1. Ensure you have the anti-theft codes for the radio and the navigation system, write down the frequencies for the radio's preset buttons.

NOTE:
The PCM memory setting is needed after reconnecting the battery.

2. Disconnect the battery negative terminal, disconnect the positive terminal.

3. Raise the coolant reservoir. Remove the battery and battery base.

4. Remove the alternator belt and alternator.

5. Remove the left exhaust manifold cover.

6. Remove the left damper fork.

7. Disconnect the left suspension lower arm ball joint.

8. Remove the left axle shaft.

9. Remove the transmission stop collar, and remove the exhaust pipe.

10. Remove the front mount mounting bolts.

11. Attach the chain hoist to the engine.

12. Remove the left engine mount bracket.

13. Disconnect the starter cable and BLK/WHT wire, remove the starter.

Sep 20, 2016 | 1997 Acura RL

2 Answers

Exhaust emissions light as come on how to rest


disconnect battery wait 5 min reconnect battery or take it to auto zone have them reset

Aug 17, 2014 | BMW X3 Cars & Trucks

1 Answer

How to fix bank 1 sensor 2 O2 sensor on 2002 ford escape


look under truck and follow exhaust system from front towards rear the o2 sensor 2 is the sensor after he cat converter it looks like a tube with a wire connection mounted on top of exhaust pipe disconnect connection and unscrew sensor replace and reconnect

Apr 11, 2013 | 2002 Ford Escape

1 Answer

My 1999 chev. tahoe backfires when i step on the gas


The problem sound like you have too much back pressure building up in the exhaust. Start by disconnecting the exhaust Y-pipe. Then start the engine and run again if the engine does not back fire, reconnect the exhaust everything after the Y-pipe. If the problem returns it is safe to say that the catalytic converters are clogged and need to be replaced.*** Make sure you use PB BLASTER or LIQUID WRENCH on the exhaust bolts to help with removal.***

Mar 29, 2012 | 1999 Chevrolet Tahoe

1 Answer

My exhaust pipe is disconnected from the muffler, how do i reconnect it?


If the out let or in let of the muffler is broken, the muffler will need to be replace. If it's not broken with u-clamps, most auto parts will have this.

Nov 11, 2010 | Ford Escort Cars & Trucks

1 Answer

I WANT TO KNOW WHERE IS THE STARTER LOCATED SO I CAN REPLACE IT..


REMOVAL & INSTALLATION 2.0L SOHC Engine With Automatic Transaxle; 2.4L Engine
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the 3 bolts attaching the Transmission Control Module (TCM). Do not disconnect the TCM wiring. Move the TCM to gain access to the upper starter mounting bolt.
  4. Remove the upper starter mounting bolt.
  5. Raise and safely support the vehicle.
  6. Remove the positive battery cable nut and disconnect the cable from the starter.
  7. Disconnect the push-on solenoid connector.
  8. Remove the lower mounting bolt that attaches the starter to the transaxle.
  9. Remove the starter from the vehicle. Fig. 3: Starter motor wiring terminal connections — 2.0L SOHC engine with A/T; 2.4L engine 90902g12.gif
    To install:
  10. Install the starter onto the transaxle and the lower mounting bolt.
  11. Tighten the mounting bolts to 40 ft. lbs. (54 Nm). NOTE: Before reconnecting the wiring to the starter solenoid, be sure to clean the wiring of any dirt or corrosion.
  12. Reconnect the positive battery cable to the solenoid post and tighten the retaining nut to 90 inch lbs. (10 Nm).
  13. Reconnect the push-on solenoid connector.
  14. Lower the vehicle.
  15. Reinstall the upper attaching bolt and torque to 40 ft. lbs. (54 Nm).
  16. Reinstall the TCM to its original location and install the mounting screws.
  17. Reinstall the air cleaner resonator.
  18. Reconnect the negative battery cable.
2.5L (VIN N) Engine
  1. Disconnect the negative battery cable.
  2. Most vehicles will require the removal of the front exhaust pipe. Use penetrating oil on the fasteners to ease removal.
  3. Disconnect the starter motor electrical connections.
  4. Remove the starter motor mounting bolts and remove the starter. Fig. 4: Exploded view of the starter motor mounting — 2.5L engine 90902g10.gif
    To install:
  5. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 20–25 ft. lbs. (26–33 Nm).
  6. Connect the electrical harness connectors to the starter.
  7. Connect the negative battery cable and check the starter for proper operation.
2.5L (VIN H) Engine
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Raise and safely support the vehicle.
  3. Loosen, but do not remove, the exhaust pipe-to-manifold retaining nuts.
  4. Place a drain pan under the oil filter to prevent oil spillage, then remove the oil filter. For additional details, refer to Section 1. Fig. 5: Loosen the exhaust pipe-to-manifold retaining nuts to provide removal clearance for the starter 90902p01.jpg
    Fig. 6: Location of the positive battery cable nut (1) and the push-on solenoid connector (2) 90902p02.jpg
    Fig. 7: After removing the oil filter for access, unfasten the retaining nut and disconnect the positive battery cable 90902p03.jpg
    Fig. 8: Disengage the push-on starter solenoid connector 90902p04.jpg

  5. Remove the positive battery cable retaining nut and battery cable from the starter.
  6. Disconnect the push-on solenoid connector.
  7. Remove the 3 bolts that attach the starter unit to the transaxle.
  8. Pull the exhaust pipe down just enough to provide clearance for the starter motor. The exhaust pipe does not have to be separated from the pipe-to-manifold threaded studs.
  9. Remove the starter unit from the vehicle. Fig. 9: Remove the 3 starter motor-to-transaxle housing attaching bolts 90902p05.jpg
    Fig. 10: Pull the exhaust pipe down just enough to provide removal clearance for the starter 90902p06.jpg
    Fig. 11: Carefully remove the starter motor from the vehicle 90902p07.jpg
    To install:
  10. Install the starter unit onto the transaxle and install the 3 mounting bolts.
  11. Tighten the mounting bolts to 40 ft. lbs. (54 Nm). NOTE: Before reconnecting any wiring to the starter solenoid, clean the wire terminals of any dirt or corrosion.
  12. Reconnect the positive battery terminal and retaining nut to the starter solenoid post. Tighten the retaining nut to 90 inch lbs. (10 Nm).
  13. Reconnect the push-on solenoid connector.
  14. Reinstall the oil filter.
  15. Lower the vehicle.
  16. Reconnect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1997 Chrysler Sebring

1 Answer

Installing ipod


Hi that harness it's located in the trunk where the CD changer sits. You need to disconnect the changer if you want to use the ipod adapter.
i hope this information was helpful.

Oct 14, 2008 | 2001 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...