Question about 1992 Isuzu Rodeo

Open Question

How to replace rear bearing on 1995 fleetwood brougham cad

Is the axle pinned inside the rear end

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: Rear Axle Bearing Replacement

That absolutely sounds like an axle (wheel) bearing. Jack up that corner of the truck and grab the top and bottom of the wheel, and shake like crazy. If you have any play whatsoever, it's a sign of a bad bearing (although you could have a bad one and not have any play - it would only mean the bearing isn't worn badly enough to cause looseness in the wheel).

You should be able to remove the axles without opening the diff up. If the axles have c-clips or snap rings on the ends inside the diff, you can usually get the axles out by dismounting them from the hubs and getting them free of all attachment except the diff, and then use a large flat-tip screwdriver as a pry bar. Use it right where the axle body mates to the diff, and lever it while you pull/yank/shake/swear at the axle, and you'll manage to pop the axle out of the diff. Sometimes it takes some time and profanity, but so far it's worked for me everytime.

Posted on Aug 02, 2008

Ad
  • 2002 Answers

SOURCE: the housing where the rear axle bearing sits is bent

Yes. It will keep the new axle under stress and probably break it again. Better to replace the housingat the same time. Check your local scrap yard for a used one.

Posted on Jun 22, 2009

  • 223 Answers

SOURCE: do you have to take the pin out of the axle gear

yes if you wish to seperate the ring and pinion gears.

Posted on Nov 27, 2010

GodBlessU
  • 3513 Answers

SOURCE: Iwould like to replace the

Hi

You have to take the cover off the rear end punkin and look where the axles go into the gears and you will see a horseshoe clip that holds the axle in, pull the clip out and the axle will pull out.

Please get back to us if you have further query else please accept the suggestion.

Thank you for contacting fixya.com

Posted on Feb 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear end axle on a 1995 poly traction police issued caprice classic


First off I think you mean Posi-traction which means both axles turn with power to the wheels. You remove the axle grease from the rear end draining it then you remove the cover try and do it slowly so that you don't make getting the old gasket off really hard after cover is off you will see the rear end look inside at the pinion gears the axle goes through them you will see how they are held on just remove the pins when putting back together use some axle grease on the splined ends and make sure that the housing and the cover is really clean so that the gasket seals properly ,nothing worse than rear end oil leaking.

Apr 20, 2015 | 1995 Chevrolet Caprice Classic

1 Answer

My fuse panel diagram is missing from my 1993 cadillac fleetwood brougham and my digital dash isnt lit..my indicator lights are working so im wondering which fuse to check


i have a 1995 fleetwood brougham and when you open the doors inside lights dont work neather does any of the in side light work with doors closed even the ones on the mirror

Nov 03, 2011 | 1993 Cadillac Fleetwood

1 Answer

Rear end makes rowing sound above 30 miles per hour also tjere is a leak of rear end grease on the left rear wheel.


THE LEAK is an axle seal leaking the noise is bearings in rear end could be axle bearing of carrier/pinion bearings while driving shift weight of truck side to side see if noise changes if so it is axle bearing if not then most likely differential bearings

May 11, 2011 | 1995 Chevrolet Blazer

1 Answer

How do i reset the oil light on my 95 fleetwood cad


1993 BROUGHAM & 1993-96 FLEETWOOD
Oil Life Indicator
1. Oil life indicator will display CHANGE OIL when oil change is needed, based upon engine oil temperatures and driving patterns. After changing oil, reset
oil life indicator.
2. To reset, turn ignition switch to ON position. Do not start engine. Fully press and release accelerator pedal 3 times within 5 seconds. If CHANGE OIL light
comes on and stays on for 5 seconds, it did not reset. Reset system again.

Jun 08, 2010 | 1995 Cadillac Fleetwood

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

1 Answer

1995 chevrolet tahoe 4x4 posi rearend axel bearing replacement how do i remove the posi unit to get the axels out?


You don't. Ever work on a rear axle. Remove cover,one bolt,pull pin and axle clip.Then pull axle, and off to auto parts store, to press on new bearing.

Feb 13, 2010 | 1995 Chevrolet Tahoe

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Rear axle bearing replacment


Not 100% sure on that vehicle & don't have manual on it at this time, but will say very common that it does have "C" like clip at end of axle. Large pin comes out first, then push axle in slightly & remove clip, & slide axle out.

Jan 19, 2009 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...