Question about Cars & Trucks

1 Answer

Does anybody know what tue time frame is for replacing the clutch/flywheel on an 07 long wheel base citroen relay

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 44,368 Answers

If it is a diesel engine then the flywheel may have the timing injection mark in the front of the flywheel facing a hole and pointer in the bell housing . This will require that the fly wheel bolt holes will be slightly off and will require you to turn the flywheel hole by hole until the bolts all screw in finger tight.. If you are asking how long should the job take 4 to 6 hours in a well equipped shop.

Posted on Mar 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: CITROEN C15 WHEEL DRIVE REPLACEMENT

Look up Euro Car Parts, they have outlets over most of GB. As for the cost. I can not shed any light on that but you should be alright at Euro.

Posted on Dec 02, 2008

  • 3 Answers

SOURCE: 1991 toyota truck clutch replacing

you'll need to bleed the hydrolic clutch theres a bleeder cockpit looks like a grease fitting on the transmission. have someone help you for this. have one perdon press the pedal down 3 times and hold it while you loosen the fitting and close it. do this till all air is out of the line remeber to keep filling fluid as you do this. good luck to you.

Posted on Dec 27, 2008

co7196
  • 3433 Answers

SOURCE: how do you remove the flywheel when replacing the clutch

Take trans out, clutch out, and remove the flywheel bolts.

Posted on May 30, 2009

alicantecoli
  • 22219 Answers

SOURCE: Hi ive got a citroen dispatch van 1.6 hdi 07

you surprise me,these vehicles are bullet proof under normal circumstances and yes the syncros can wear out like any make of vehicle ,but this old grandad who passed his test in a viva with no syncro on first gear ,and passed his hgv on a vehicle with no syncros at all was taught to drive in a different era and rule one was neutral and handbrake on when stopped ,not holding it on a hill by slipping the clutch ,secondly to not put a vehicle in first gear whilst moving ,well it wouldnt go anyway ,double the clutch between gears so as to reduce the wear on the syncros and gears .not to ride the clutch between changing gears and also change down using double the clutch to save the brakes and stop vehicle slipping or skidding on a wet road ,not fly up to a roundabout ,slam on brakes force it into first gear at 30 mph then try to imitate evil kenival by going around on two wheels .This sort of driving will only damage the gearbox like syncros and clutches not lasting very long .

Posted on Jul 03, 2010

emissionwiz
  • 76649 Answers

SOURCE: hi guys, have citroen relay '08' plate 2.2 hdi. is the clutch hydrolic or cable? also struggling to get reverse gear, all others no problem at all. any ideas?

It is hydraulic. Are you engaging 2nd gear prior to reverse to slow gear motion and ease reverse effort? Is the engine idle speed with specs?

Posted on Sep 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Flywheel replacing


you will need a replica flywheel and new bolts plus torque range and manfacturers specs.

Nov 07, 2016 | Cars & Trucks

1 Answer

Citroen xsara 1.8 16 valve 1999 firing order is it from left or right side?


This is where it gets tricky, Graham, the French have started calling the flywheel end, cylinder no 1, on some engines. As the timing is not adjustable is it just that you need to know which lead goes where?
You can see the no 1 position usually through a hole in the bellhousing which is marked on the flywheel. A blob of white paint or Tippex can help highlight it.

Jun 01, 2014 | Citroen Xsara Cars & Trucks

1 Answer

Changed brakes on 07 citroen c4 now abs light on


Hi Caroline.
The ABS sensors are in the same area where the brake work has been done. Most likely a broken wire or loose connection behind one of the wheels. Ask garage to inspect / scan for fault codes to pinpopint which wheel has the problem.

Dec 04, 2013 | Citroen Cars & Trucks

1 Answer

Flywheel or something grings against the starter when clutch is engaged


There is no way the ring gear will hit the starter pinion unless the fly wheel bolts on the crank shaft or loose allowing the flywheel to run out of true. If you have had clutch/ rear seal work done lately the fly wheel will only fit in one position and if that was ignored at some time then the fly wheel will run out and touch the starter pinion.. I would also check the adjustment on the starter pinion as it has to be set by the lever pivot to a correct distance or it will touch the teeth of the ring gear

Jul 28, 2013 | 2001 Ford Escort ZX2

2 Answers

Clutch seems to be slipping I put everything in new


Sounds like bad clutch but that should have been replaced when fly wheel fly wheel worked on.

Jan 15, 2013 | 1992 Jeep Wrangler

1 Answer

Hi guys, have citroen relay '08' plate 2.2 hdi. is the clutch hydrolic or cable? also struggling to get reverse gear, all others no problem at all. any ideas?


It is hydraulic. Are you engaging 2nd gear prior to reverse to slow gear motion and ease reverse effort? Is the engine idle speed with specs?

Sep 18, 2012 | Citroen Cars & Trucks

2 Answers

Clutch only lasting 5000- 8000 miles been replaced twice on warranty original clutch was good for 68000miles what could be problem? citroen saxo had car from new 52 plate 1.4i not driven any differently


Are they replacing/resurfacing your pressure plate when they replace the clutch. Is it possible you have an oil leak that is causeing the clutch to slip?

Dec 08, 2010 | 2005 Peugeot 405

1 Answer

Hi ive got a citroen dispatch van 1.6 hdi 07 plateive had upto date first and second syncros done the a new gear box with linkages the all the syncros with gears and a new clutch but it has done it again...


you surprise me,these vehicles are bullet proof under normal circumstances and yes the syncros can wear out like any make of vehicle ,but this old grandad who passed his test in a viva with no syncro on first gear ,and passed his hgv on a vehicle with no syncros at all was taught to drive in a different era and rule one was neutral and handbrake on when stopped ,not holding it on a hill by slipping the clutch ,secondly to not put a vehicle in first gear whilst moving ,well it wouldnt go anyway ,double the clutch between gears so as to reduce the wear on the syncros and gears .not to ride the clutch between changing gears and also change down using double the clutch to save the brakes and stop vehicle slipping or skidding on a wet road ,not fly up to a roundabout ,slam on brakes force it into first gear at 30 mph then try to imitate evil kenival by going around on two wheels .This sort of driving will only damage the gearbox like syncros and clutches not lasting very long .

Jul 03, 2010 | Cars & Trucks

3 Answers

KEYCODE light permanently lit on Citroen Relay van,


before u buy have trouble code scanned most auto stores offer service for free ==can be as simple as a bad key[not recognized] to big such as electrical anti -theft system

Apr 26, 2010 | 2006 Fiat 124

1 Answer

Clutch


Usually when a clutch goes, the parts people won't warranty the clutch, unless you have the flywheel resurfaced, and buy a new pressure plate. I can't imagine how a flywheel could be damaged to the point of replacement, without the clutch itself being severely damaged. No. This is certainly not normal practice. Ask them what damaged the flywheel?

Jun 15, 2009 | 2000 Kia Sephia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...