Question about 1986 Nissan 200SX

Open Question

I have a nissan largo that cuts out when i put it in gear done a fault code reading comes up with code 1-5 =lean mixture 1 8= ant got a clue code 2 1= IAC valve or its cicuit fault no ignition signal from ECM does it want a ECU or may be a fuel injector pump. thanks marg12 forgot to add it a 96 nissan largo 2lt diesel.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
pippall
  • 1486 Answers

SOURCE: Engine check on

change the mass air flow meter.That seems to be your problem.

Posted on Jul 17, 2009

Ad
  • 1 Answer

SOURCE: what does engine fault code po171 system too lean bank 1 mean thanks

i think its the oxygen sensor (pre cat) in exhaust

Posted on Sep 23, 2008

  • 1 Answer

SOURCE: i cant find the lift pump on my nissan largo?

i have a nissan largo 96 2 lt diesel that keeps stalling when i put it in reverse and chucks black smoke out it also stalls at lights but always starts put a fault code reader on and it has come up with numbers 1-5 =lean mixture but its deisel ? 1-8 ant got a clue with that one , and code 21 does any one think it the ECU ?SOME ONE THINKS IT COULD BE injector pump ?my engine management light flashing now.thanks marg

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: I have a 84' nissan diesel pickup with the sd25

loosen the nuts holding the fuel lines to the injectors, roll engine over and once fuel comes out, retighten nuts until all are tight again. After that, look at the stop solnoid as it will cut the fuel flow also

Posted on May 09, 2010

ZJLimited
  • 17970 Answers

SOURCE: 1993 nissan altima code 21 ignition signal - how to fix/repair

Replace the O2 Sensor, reset the ECU, and subject solve.

Good luck.

Posted on Jul 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan largo


Did you have it scanned for codes? If codes come up follow the diagnostic sequence. Cam or crank sensor may cause this, but I would get it scanned!

May 31, 2014 | 1996 Nissan Pathfinder

1 Answer

My 96 largo seems to have a lag going up hillsit stays around 2000 revs i have to push the pedal to the floor then sudenly it will zoom up to 3000+ revs and when idling at the lights it starts going put...


have the OBD codes read as there are a number of things that could cause these symptoms the OBD code will pinpoint the sensor/switch at fault, i would guess at an air/fuel problem but the OBD code will give a thorough diagnosis and save you time and money searching for the fault blind, keep me posted if you wish

May 22, 2014 | 2004 Nissan Nissan almera tino

1 Answer

My 2005 Nissan Altima 3.5 is idling at 800 rpm's, and my service engine soon light came on. The code read for a Chrysler? P1283, and Fuel pump module detected an incorrect low idle, low idle select...


Make sure you are looking up the code properly. 1283 for Nissan indicates a lean condition on bank 2. See link below. A vacuum leak is likely, but make sure the new sensor is recalibrated. Did you perform the relearn procedure after replacing the sensor? If not, see the second link below. If you ran the relearn procedure and cleared all codes but 1283 comes back, look for a loose vacuum line or leaky intake manifold gaskets. P1283 Nissan Air Fuel Ratio Sensor 1 Lean Shift Monitoring Bank 2 1998 2012 Nissan Altima Clear Mixture Ratio Self Learning Control Data

Jun 21, 2017 | Cars & Trucks

2 Answers

Bmw 2882/3 fault codes present


You most likely have an engine vacuum leak or a defective mass airflow sensor or low fuel pressure. Read the codes with a OBD2 code reader and see what the standard codes are.

Oct 14, 2012 | Cars & Trucks

1 Answer

The check light is flashing on my diesel 96 Nissan Largo.


It is better to use a scanner to find the outcome fault code and then you carry on. Do not try to fix on suspicion .

Sep 09, 2012 | Nissan Cars & Trucks

1 Answer

2007 entourage code p2187 p2189 p0171 p0174 keeps coming on cleaned mass air flow sensor with crc cleaner dont see any vacuum leaks ????help?


Here is two of your codes. Lean mixture on banks 1 and 2. There are 37 pages of Hyundai codes.

http://www.autocodes.com/p0171_hyundai.html

P0174 HYUNDAI - System Too Lean Bank 2

Read more: http://www.autocodes.com/p0174_hyundai.html#ixzz43IA8HGCb

P2187 HYUNDAI - System Too Lean At Idle Bank 1. P2189 will be Bank 2 at idle.

Read more: http://www.autocodes.com/p2187_hyundai.html#ixzz43IASlusU

Check all the bolts holding the plenum, and anything else concerned with air intake. Too much air means weak mixture.

Feb 05, 2011 | 2008 Hyundai Entourage

1 Answer

Codes


Your sensors are reading correctly so leave them alone. What you have is a fuel delivery issue. Your MAF sensor is telling your engine to lean your fuel mixture. You need to remove and clean or replace (is better) the MAF. But first replace your PVC valve and clean your ERG valve.

Jan 20, 2010 | 2000 Dodge Intrepid

2 Answers

4 codes P0171,P0174,P2195,P2197


Hi
171 system too lean
174 system too lean
2195 - 02 ozygen sensor signal stuck lean Bank1 Sensor 1
2197- 02 ozygen sensor signal stuck lean Bank 2
Sensor 1
The 2 front 02 sensors are located on the front of
the exhaust manifold.
Should solve problem and increase gas mileage.

Apr 01, 2009 | 2003 Ford Expedition

4 Answers

I cant find the lift pump on my nissan largo?


i have a nissan largo 96 2 lt diesel that keeps stalling when i put it in reverse and chucks black smoke out it also stalls at lights but always starts put a fault code reader on and it has come up with numbers 1-5 =lean mixture but its deisel ? 1-8 ant got a clue with that one , and code 21 does any one think it the ECU ?SOME ONE THINKS IT COULD BE injector pump ?my engine management light flashing now.thanks marg

Nov 13, 2008 | Nissan Minivan Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...