Question about 2004 Chrysler Concorde

1 Answer

When i try to start my car the starter just rapidly ticks. i took the starter in and its fine so i tried to turn the crank pully and the flywheel but neither of them will move.

What would make the crank pully and flywheel not turn by hand?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

If they will not turn in either direction, your engine is seized.
If it turns in one direction then stops you have an obstruction either inside the engine (catastrophic) or between the engine and transmission (such as loose flywheel bolts) stopping the engine from turning.

Posted on Mar 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 154 Answers

SOURCE: Got a new starter but it stilll won't run.

Yes the transmission has to come out to replace the flywheel. An depending on how nice the shop will be to you, the labor hours can be 4 to 6 billable hours plus parts. What ever the going shop rate is where you live. 90$ + per hour. It mre than likely has damaged teeth on the ring gear. The factory had a spacer/shim around the nose of the starter. Did you have to deal with that when you replaced the starter> They very often don't get reinstalled and are a bit of a pain to get into place properly. Without the shim the spacing would not be proper and possibly cause premature wear to starter and or Ring Gear.

Posted on Apr 01, 2009

  • 16 Answers

SOURCE: 2002 chrysler sebring LXI coupe would not start 2

They have either left a wire to the starter unhooked or they have blown a fuse or fuselink

Posted on Jun 16, 2009

shadtremonky
  • 353 Answers

SOURCE: b4 turn key start immed-now need hold key lond time to start

replace spark plugs?
replace fuel filter?
check battery voltage or replace?

Posted on Aug 07, 2009

  • 3 Answers

SOURCE: car wont start but lights

Give some more details of the problem.

Posted on Jul 15, 2011

pcdj64
  • 1150 Answers

SOURCE: all comes on when key

Does the car have a factory security system? it may have a starter kill on it.
also check for voltage at the starter solenoid while someone holds the key to start position, you could have a faulty ignition switch.
the engine light stays on when the key is on until engine starts.

Posted on Sep 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 Accent wont start. It started fine Tuesday, Wednesday morning it would not start for nothing. I tried it Thursday afternoon and it started fine. This is the second time it has done this.


Does the motor crank (starter engaged and turning the motor)? If it does not crank, do you hear the solenoid clicking (engaging the starter gear into the flywheel teeth)?

Nov 25, 2016 | Hyundai Motor 2004 Accent

1 Answer

I have a crown vic 1998 my car was driving fine i was going to go to the store my car didnt turn on i open my hood i try to turn it on all i hear was i think the starter but the crazy thing is the band...


So you think you could hear the starter spin but the "band" did not turn? I suppose you mean the serpentine belt did not turn. It is quite possible for the starter to spin but the bendix to fail to engage the flywheel. This can be caused by low battery charge, bad battery connections, or more commonly, a bad starter.

Jan 08, 2015 | 1998 Ford Crown Victoria

3 Answers

Blazer will not start have gas battery is fine


If I understand you right, it sounds like the starter solenoid went bad and could possibly work again when the engine cooled down. The other scenario is that the ignition switch is bad (on steering column) or the neutral safety switch located on the transmission side. A real fluke would be that the starter BOLTS CAME LOOSE AND JAMMED THE STARTER, IF THIS IS THE CASE LOOSEN STARTER BOLTS, WIGGLE STARTER THEN TIGHTEN BOLTS TO SPECS. 25268178-sbjsv11dlntqjzkc4qi5qeet-5-0.gif

Nov 03, 2014 | 2000 Chevrolet Blazer

1 Answer

Engine will not turn over


Try turning the engine manually . this can be done off the front of the crank shaft bolt i think it is a 15/16 hex bolt if you can not turn it the engine main bearings are seized to the crank shaft if it turns then a voltage drop test needs to be done.

Apr 19, 2014 | 2003 Ford Excursion

1 Answer

Starter works fine but won't crank engine. the pick up has to be given a push first before it starts


If the starter is spinning when you try to start but doesn't spin the engine over then you most likely have teeth missing off the flywheel ring gear. The facts that you say you have to push it and then it starts means the flywheel position changes and the starter has good teeth on the flywheel to engage. To confirm this next time the engine won't crank over remove the starter and look inside at the flywheel for missing flywheel teeth.

Mar 13, 2012 | Ford Cars & Trucks

2 Answers

Grinding noise when ignition is turned


THe starter engages the fly wheel and in the process turns the motor over to cause it to crank. The grinding can be a bad starter causing the gear to either not engage fully or not disengage. It can also indicate missing teeth on the flywheel from damage from starter. If the car cranks and grinding goes away it points to the starter solenoid not engaging properly.. pushing gear into contact with flywheel. I would recommend replacing the starter and you can replace it with a good mechanical knowledge and DIY.

Jun 08, 2010 | 1997 Chevrolet Cavalier

2 Answers

When I try starting the car, it makes a fast ticking noise....the batery is good cause everything turns on with it but when I ignite, it ticks. Is it the starter?


THat is the starter my friend but why dont u try to jump start the car and see if this helps. That most likely sounds like a bad battery to me. As you are hearing the starter still is trying to go but doesn't have enough power to kick its gear into the flywheel.

Apr 12, 2010 | 2002 Hyundai Accent

1 Answer

1990 4 runner. has elect. power but won't start . starter won't crank


check voltage at starter if 9volts or better replace starter if lower check battery cables also check engine oil and make sure engine turns by turning center bolt on crankshaft pully or flywheel after u remove old starter u can use srew driver or prybar

Apr 01, 2009 | 1986 Toyota 4Runner

2 Answers

1993 Ford Crown Victoria won't start....


this happened too me and a friend of mine the front pump went out of the tranny and locked up i like too never found the problem but its so bad that it locks up the engine, put a socket on the crank pully and see if you can rotate the engine if not its the tranny locked up

Mar 06, 2009 | 1993 Ford Crown Victoria

Not finding what you are looking for?
2004 Chrysler Concorde Logo

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...