Question about Cars & Trucks

1 Answer

2009 Chrysler 300 stereo got stolen now my car wont start what do I do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,005 Answers

You need the dealer to install the factory radio so the theft deterent system will stop locking you out.

Posted on Mar 20, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

localwonder
  • 6784 Answers

SOURCE: The car cranks but won't start

Ok, check the following below--

1. Check the Ignition control Module for its operational value. it may be damaged.

2. Check the coils.
3. Check the plugs and wires.
4. Check the ECM/PCM/ECU(All represent the same device that is commonly known as the engine control computer)

Check these areas thoroughly for faults. I would also advise to replace the fuel filter and fuel pump as well.

Posted on May 31, 2009

  • 21 Answers

SOURCE: Car stuck in Park, wont switch gears

check to see if the brake lights come on it may be a problem with a brake switch under the dash not letting the shift lock release. there may be a seperate switch just for it so check and see it there is two switches touching the brake pedal lever if the brake lights come on.

Posted on Jun 09, 2009

  • 1071 Answers

SOURCE: 2006 Chrysler 300 car wont start cant read the ecu

check battery and fuses

Posted on Jul 23, 2009

  • 82 Answers

SOURCE: gear stuck

Do you have full power on your car's battery?
Sometimes, if it isn't sufficient, the transmission will not shift, as it is electronically controlled.

Posted on Sep 06, 2009

SOURCE: chrysler 300 ran outof gas

There is no fuel pump reset button, it's a fuse. Check the fuse box and replace the fuel pump fuse. Replace the fuel filter first if you are having fuel delivery problems

Posted on Nov 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Chrysler 300 vibration when brakes applied


have the disc rotors checked for warp age
they warp from heat or too thin
have it done in a brake specialist shop
the fix will be new rotors

Feb 01, 2016 | 2009 Chrysler 300

1 Answer

Steering problems chrysler 300 2009 V8 5.7L


Most likely the pump is providing too high a pressure due to a faulty or incorrectly adjusted relief valve, though it is possible the working clearances inside the pressure cylinder exceed specifications.

I suggest a peak pressure test of the hydraulic pump before further repairs are carried out.

Feb 25, 2015 | Chrysler Cars & Trucks

1 Answer

Wiring diagram wire colors


type in (images of wiring diagrams 2009 Chrysler 300 ( and area that you need ) YOU WILL NOT GET THE WHOLE CARE use subsections =like fuse box=temp sensor and so on.

Sep 04, 2014 | 2009 Chrysler 300

1 Answer

Etc light on 2009 Chrysler 300


Whenever this warning or any other stays on in the dash it is indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Oct 04, 2012 | 2009 Chrysler 300

1 Answer

I have a chrysler 300 touring, 3.5L. There are two keys and a remote start. I cannot start the car with the second (spare) key. I can actually start but it automatically shuts down and it wont even start...


Since the second key does not have the electronics in the case, it will not allow the car to run, as it thinks its being stolen. If you give your local chrysler dealer your VIN number, they should be able to produce a second key that will start the car. (VIN number is found at the bottom of the windshield on the driver's side or on you ownership)

Mar 06, 2011 | 2005 Chrysler 300

1 Answer

How do i reset the oil light after changing the oil on a 2009 chrysler 300


turn the key on and wait for the change oil light to flash,when it does press the acelerter down three times slowly, it should the reset it self.. i found this out by reading about it in my owners manual

Oct 09, 2010 | 2009 Chrysler 300

3 Answers

RESETTING CHECK ENGINE LIGHT


I can only assume you have had the code extracted and fixed the problem and looking to do a reset only. If you have not fixed the problem the reset wont do any good. That being said, in most all chrysler vehicles, the check engine light can be reset by disconnecting the negative battery cable for at least 15 seconds. However on OBD II (usually 97 and newer) models the light can only be reset with the use of a scan tool. CAUTION : If the stereo in your vehicle is equipped with an anti-theft system, make sure you have the correct activation code before disconnecting the battery cable.

Sep 26, 2008 | 2006 Chrysler 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...