Question about 2002 Dodge Caravan
The windshield washer works great when in park, when slowing or when braking, but for some $^&^&^*&^$ reason wont work when foot is on gas pedal??? Tank is full of fluid, as said works great at low speeds or stopped like when waiting for a light to change or foot on brakes
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The master cylinder has failed, the fluid bypasses from one cylinder to the other, this is really 2 cylinders in one, the brake system is split in an X pattern.
Posted on Nov 06, 2008
SOURCE: stuck parking brake
take rear wheels off and find the cable and bang it free or get under the car and look for the cable and try to pull it free if you get it off dont use it again!
Posted on Jun 30, 2009
go to a service station with an air compressor and with the air turned down to about 20 lbs blow into the washer top small hole to force fluid thru the hoses,not a lot of pressure so you blow hoses off or rupture something
Posted on May 30, 2010
SOURCE: 05 neon windshield washer tank
its a simple job but first buy the pump and you will see where the bolts/screws go then you will be able to remove same on car and fit new.before buying though,try removing a hose from the pump and get someone to operate the switch,might just be s..t in the pipe.
Posted on Aug 20, 2010
Tips for a great answer:
Body control module (BCM)
Wiper 1 relay
Wiper 2 relay
Windshield wiper motor
Windshield washer pump
Windshield washer nozzles
Windshield washer solvent container
Windshield wiper arm and blade assemblies
Windshield wiper transmission
WIPER/SW 10A fuse
WIPER 25A fuse
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
Dec 05, 2015 | Cars & Trucks
Mar 20, 2014 | 2002 Dodge Caravan
Jan 14, 2014 | 1990 Ford F150
Sep 28, 2013 | 1999 GMC Jimmy
Apr 14, 2013 | 2006 Dodge Dakota
Apr 06, 2013 | 1999 Cadillac DeVille
Aug 28, 2010 | 1999 Chevrolet Silverado 1500
Dec 18, 2008 | 2001 Lincoln Navigator
Jul 09, 2008 | 2003 Volkswagen Golf
Oct 04, 2016 | 2002 Dodge Caravan
81 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: