Question about 2000 Dodge Stratus

2 Answers

Turn signals and Hazard no longer work

The turn signals would intermittently work: Replaced the flasher relay assembly - worked but when I turned on the hazards a quick clicking was heard, then the flashers stopped working: Replaced the OEM flasher model - neither the turn signals or the hazards work now.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 2,899 Answers

Flasher and fuses are usually under the dash next to the drivers left knee.
Hope this helps.

Posted on Mar 19, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Fast clicking is caused by a higher than normal current being applied. Normally a short or a aftermarket relay that requires less current to switch. Sounds like the entire multifunction switch is bad.

Posted on Mar 20, 2014

  • rrb6699 Mar 21, 2014

    i always check for a signal light out when the quick signal clicking happens. i suspect your steering wheel column electrical (usually ignition switch) is faulty.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

wilsodfarm
  • 986 Answers

SOURCE: 1998 Dodge 2500 pickup turn signals, hazards

There is a conector box on the left side of your steering wheel on the colum loosen it and check your wires I bet when you just loosen the block they will start working,I hope this helps you

Posted on Oct 08, 2009

wracefans24
  • 1985 Answers

SOURCE: 2000 Dodge 3500 van. Turn signals, hazards not working

multi function switch

Posted on Dec 02, 2009

  • 31 Answers

SOURCE: turn dignals and hazard lights do not work

the turn signal awitch goes bad on those vehicles causing niether to work

Posted on Feb 12, 2010

pst4911
  • 41 Answers

SOURCE: 1992 dodge dakota - front

Maker sure your flasher is ok and that you are getting power you will have to trace it from there

Posted on Oct 29, 2010

  • 1949 Answers

SOURCE: 2000 Dodge Intrepid: Used the hazard

need to replace multi-funtion switch

Posted on Dec 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy blazer . Problem is the horn does not work and turn signal flashes fast on both sides.


Do you know how to do automotive electrical testing ? Do you know what a relay is and how it works ? Turn signals flashing fast , could be aburnt bulb , flasher module .
VEHICLE RELAYS Operation Diagnosis
Turn Signal Lamps
The HAZ LP fuse in the underhood fuse block supplies battery positive voltage to the multifunction hazard switch assembly. The TURN fuse in the IP fuse block supplies Ignition positive voltage to the multifunction turn signal switch assembly. With the ignition switch in the RUN or START position, ignition positive voltage is connected through the multifunction turn signal and hazard switch assembly to the flasher module which is grounded at G205. When the turn signal switch is placed in either the left or right position, the circuit is complete from the flasher module to the turn signal lamps and to ground. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is activated, all turn signal lamps will flash including both IPC turn indicators. The front turn signals are grounded at G111 and G112. The rear turn signals are grounded at G475 and G422 on the pickup and G450 on the utility.

Aug 26, 2017 | Cars & Trucks

1 Answer

Turn signals wont work but flasher an lights come on


If the hazard flasher is working but the turn signals aren't, the problem is most likely either fuse A11 or the #2 relay in the trunk fuse block. However, if these check out, the problem could be either the turn/hazard switch assembly or the turn flasher module.

If both the turn signals and hazard flasher are not working, the most likely problem is the turn/hazard switch assembly.

May 26, 2015 | 1994 Cadillac DeVille

1 Answer

Fix signal lights


If the hazard flasher is working but the turn signals aren't, the problem is most likely either fuse A11 or the #2 relay in the trunk fuse block. However, if these check out, the problem could be either the turn/hazard switch assembly or the turn flasher module.

If both the turn signals and hazard flasher are not working, the most likely problem is the turn/hazard switch assembly.

May 03, 2015 | 1996 Cadillac DeVille

1 Answer

2000 impala,emer. flasher and turn signal not working; have replaced turn signal switch


you may have a bad flasher relay. its also known as a hazard relay, or turn signal flasher.

Jul 18, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

Turn signals were intermittent and now will not


It is absolutely possible, and recalls are free. Take the free recall and hope it solves your issue!

Dec 10, 2009 | 2001 Oldsmobile Alero

1 Answer

Turn signals quit working. Can't find a fuse labeled for turn sig


Check the flasher unit on both turn and hazard lights,

make sure hazards are off
if hazard flasher bad and and on it will interfere with turn signal

Sep 05, 2009 | 2001 Dodge Ram 1500 Truck 2WD

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Have hazard lights but no running or turn signals


sounds like you need a combo flasher assembly..located in fuse block inside vehicle under steering column..there may be a plastic cover under dash you have to remove to see fuse block..large black relay that plugs into fuse block..if you pick up a new one,you will see what it looks like..available at dodge dealer..combo flasher or drl/signal relay

Jun 11, 2009 | 1999 Dodge Caravan

1 Answer

Signals and Four Way Flasher working intermittently


Replace the hazard switch, It has the turn signal flasher built in to it.

Apr 09, 2009 | 2003 Chevrolet Monte Carlo

2 Answers

Turn signals don't work


i have a similar problem but my left signal works, when i turn the right on it just does an annoying buzz sound. if you can think of any explination for such shinanogins help would be greatly appreciated

Nov 25, 2008 | 1989 GMC K1500

Not finding what you are looking for?
2000 Dodge Stratus Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...