Question about 2001 Mazda MPV

Open Question

Airbag light came on , on my mazda 2001 mpv,code 45

My wife took car out, and whilst driving she said passenger restraint light came on.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
StormStrikes
  • 104 Answers

SOURCE: how do i get the trouble codes off a 1989 mazda mpv?

http://img178.imageshack.us/img178/3331/obdikx3.jpg

The above link is to a diagram of your ALDL connector, all you need is a paper clip, straighten out the paper clip and insert one end into the diagnostic test pin and one in the system ground pin (terminals A & B).

Then put the key in the ignition and turn it to the on position but DO NOT start the engine. You will then see the check engine light flash. It will initially start by flashing once, then a pause and then flash twice and it will repeat this three times. That flash sequence indicates 12, which just means the system is operating. Its the flash sequences after that that will give you the code if any are stored.

For instance if it flashes twice, then pauses, then flashes four times, thats code 24. So any flash sequence you get after the initial 12 (flash once, pause, flash twice) you need write those down. Below is a list of diagnostic codes to tell you what the codes mean.

Code 12
1 flash, pause, 2 flashes
Diagnostic: This Code will flash whenever the diagnostic terminal is grounded with the ignition switch turned on and the engine is not running.

Code 13
1 flash, pause 3 flashes
Oxygen sensor voltage stays between 0.35 and 0.55 volts for 30 seconds when the TPS signal was above 0.55 volts. The engine had been running for at least 40 seconds with an engine temperature above 110° F.

Code 14
1 flash, pause, 4 flashes
Coolant temperature sensor signal indicates a temperature of over 284° F for 4 seconds after the engine had been running for at least 10 secondsCoolant Sensor Circuit (high temperature) If the engine is experiencing overheating problems, have those fixed before continuing. Check all wiring and connectors associated with the coolant temperature sensor. Replace the Coolant temperature sensor.

Code 15
1 flash, pause, 5 flashes
Coolant Sensor Circuit (low temperature) Coolant temperature sensor signal indicates a temperature colder than -36° F for at least 4 seconds after the engine had been running for 2 seconds. See above, then check wiring connections at the ECM

Code 16
1 flash, pause, 6 flashes
Charging system voltage was either below 9 volts or above 17 volts for 10 seconds. System High Voltage If the voltage is above 17.1 volts for more than 2 seconds, the Service Engine Soon light will illuminate. Have the charging system checked.

Code 17
1 flash, pause, 7 flashes
PCM did not detect any spark reference pulses within 240 fuel control reference pulses (80 crank revolutions) while engine was running below 1200 RPM. Spark Reference Circuit.

Code 21
2 flashes, pause, 1 flash
Throttle Position Sensor, TPS voltage was above 0.8 volts for 5 seconds when engine was running and air flow was less than 15 gm/sec, or the TPS voltage was over 4.8 volts at any time.

Code 22
2 flashes, pause, 2 flashes
Throttle Position Sensor check TPS adjustment. Replace the TPS sensor. TPS voltage was under 0.2 volts for 4 seconds when the ignition was on. Check for a sticking, or mis-adjusted throttle position sensor.

Code 23
2 flashes, pause, 3 flashes
Inlet air temperature sensor signal showed an air temperature of -29° F for 4 seconds. Manifold Air Temperature. Check the MAT sensor, wiring, and connectors for a possible open circuit. replace the MAT sensor.

Code 24
2 flashes, pause, 4 flashes
Vehicle speed sensor signal showed less than 3 MPH for 2 seconds when engine speed was greater than 3000 RPM and transmission has not been in park or neutral for more than 4 seconds. Or vehicle speed goes from above 18 MPH to 0 in less than 2 seconds without applying brake. This code can only appear when the vehicle is in motion, if it appears when the car is not in motion, ignore it. Check ECM connections, any other problems should be diagnosed by a qualified mechanic.

Code 25
2 flashes, pause, 5 flashes
Inlet air temperature sensor signal showed an air temperature of over 218° F for 5 seconds when vehicle speed was greater than 35 MPH. Check the voltage between the MAT sensor and the ECM. voltage should be above 4 volts.

Code 26
2 flashes, pause, 6 flashes
Quad-Driver sense voltage shows a low voltage when battery voltage should be present, or if the sense voltage shows battery voltage when a low voltage should be present for at least 5 seconds when the engine was running. Have the car checked by a dealer.

Code 27
2 flashes, pause, 7 flashes
2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started. Gear switch Diagnosis Have the car checked by a dealer.

Code 28
2 flashes, pause, 8 flashes
3rd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 3rd or 4th gear switch was open when engine was first started.

Code 29
2 flashes, pause, 9 flashes
4th gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 4th gear switch was open when engine was first started.

Code 31
3 flashes, pause, 1 flash
PRNDL indicates a gear other than park or neutral for 13 seconds for 3 consecutive startups when ignition was on, engine was off and vehicle speed was 0. Or the PRNDL status indicators (A, B, C, P) showed an incorrect combination of Lo and Hi for more than 10 seconds.
Check all connectors, and for a faulty switch.

Code 32
3 flashes, pause 2 flashes
EGR System Check vacuum hoses and connections for leaks and restrictions. Replace the EGR solenoid or valve.

Code 33
3 flashes, pause, 3 flashes
MAF Sensor Have the mass air flow sensor replaced.

Code 34
3 flashes, pause, 4 flashes
There was no MAF signal for over 4 seconds while engine was running. Check for loose or damaged air duct, misadjusted minimum idle speed and cacuum leaks. Inspect the MAF sensor and the electrical connections.

Code 38
3 flashes, pause, 8 flashes
The Torque Converter Clutch portion of the brake switch was open and caused the TCC to be inoperative, adjust OR replace switch.

Code 39
3 flashes, pause, 9 flashes
Torque Converter Clutch Check ECM connections, check for faulty Torque Conver Clutch solenoid.

Code 41
3 flashes, pause, 1 flash
Cam sensor signal was not received by PCM for the last 5 seconds while engine was running. Check for faulty connections, or a faulty cam sensor. Maybe also indicate a problem with the vehicle's timing chain.

Code 42
4 flashes, pause, 2 flashes
The Electronic Spark Timing (EST) signal did not change when the ECM applied bypass voltage to the ignition module. Check for faulty connections, or a faulty ignition module.

Code 43
4 flashes, pause, 3 flashes
Knock sensor signal was either above 3.5 volts or below 1.5 volts for at least 20 seconds. Check for a faulty knock sensor, or Mem-Cal.

Code 44
4 flashes, pause, 4 flashes
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 45
4 flashes, pause, 5 flashes
Oxygen sensor voltage was over 0.75 volts for 2 minutes in closed loop operation with a throttle angle between 0.6 and 1.9 volts. Rich exhaust. Check the evaporative charcoal canister and its components for the presence of fuel.

Code 46
4 flashes, pause, 6 flashes
Power Steering pressure switch Check for faulty connections, or a faulty switch.

Code 48
4 flashes, pause 8 flashes
Misfire Diagnosis. Check the ignition and fuel systems.

Code 51
5 flashes, pause, 1 flash
Prom or Mem-Cal Make sure the MEM-Cal or prom is properly installed in the ECM. Replace Mem-Cal or prom.

Code 52
5 flashes, pause, 2 flashes
Cal-Pak Check the Cal-Pak to insure properation. replace the Cal-Pak.


Code 54
5 flashes, pause, 4 flashes
EGR #2 solenoid was out of range for 6 of 8 tests. 55 EGR #3 solenoid was out of range for 3 of 5 tests.

Code 55
5 flashes, pause, 5 flashes
ECM Check for faulty connections. Replace the ECM.

Code 56
5 flashes, pause, 6 flashes
Quad-driver voltage was incorrect for 5 seconds on the circuit connected to QDM "B".

Code 57
5 flashes, pause, 7 flashes
Boost control solenoid did not open bypass valve causing engine torque to be too high.

Code 63
6 flashes, pause, 3 flashes
EGR flow was incorrect. EGR solenoid did not work properly. Have vehicle serviced by a dealer.

Code 64
6 flashes, pause, 4 flashes
Same as Code 63 EGR flow was incorrect. EGR solenoid did not work properly.

Code 65
6 flashes, pause, 5 flashes
Same as Code 63.

Posted on Dec 31, 2008

Ad
  • 840 Answers

SOURCE: power windows on 2001 mazda mpv won't go up?

if you do not here the motor then its the regulator or motor that needs to be replaced/ cif you hear the motor check the control switch on the trim panle coould be just a five dollar part to replace/ Please rate my response thank you very much

Posted on Jan 31, 2009

stuarttx
  • 15 Answers

SOURCE: program remote control for mazda mpv 2002

Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Posted on Feb 21, 2009

  • 1986 Answers

SOURCE: I am getting a P0031, P1512, & P0421 code

P0031 - most likely pointing to a failed O2 sensor (bank 1 sensor 1 is located before the catalytic converter)

P0421 - failed catalytic converter or a failed O2 sensor

P1512 - intake manifold shutter valve is stuck - may be caused by the O2 sensor, but may not

I recommend replacing your O2 sensor first and see what happens

Posted on Sep 18, 2009

  • 1986 Answers

SOURCE: I have a Mazda 2001 MPV, just had service for o2

blinking light means engine is misfiring. continuing to drive will severely damage the engine. The O2 should not be related to your engine misfiring

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the airbag light to go off on a 2007 Chevy van Express


You need to find out what code or codes are stored in the airbag control module > There are a lot of components involved in your airbag system : If you haven't had any training on these systems your best bet is take it to a ASE certified repair shop . People have been killed messing with these systems not knowing what they were doing .
The frontal SIR system consists of the following components:
?€¢
AIR BAG indicator located on the instrument panel cluster (IPC)


?€¢
Driver and passenger knee bolsters


?€¢
Inflatable restraint front end sensor


?€¢
Inflatable restraint PASSENGER AIR BAG ON/OFF indicator located on the instrument panel


?€¢
Inflatable restraint Passenger Presence System (PPS)


?€¢
Inflatable restraint I/P module


?€¢
Inflatable restraint I/P module disable switch


?€¢
Inflatable restraint seat position sensors (SPS) (left/right)


?€¢
Inflatable restraint sensing and diagnostic module (SDM)


?€¢
Inflatable restraint steering wheel module


?€¢
Inflatable restraint steering wheel module coil


?€¢
Inflatable restraint wiring harnesses


?€¢
Seat belt pretensioners (left/right)


?€¢
Steering wheel and column

Nov 22, 2015 | Cars & Trucks

1 Answer

My airbag light flashes three times then pause then one flash the car is a Mazda MPV 2004 ? did have the battery disconnected for reparts atford dealer would think they would have reset it but now try


They probably forgot to connect something. Look around where they were monkeying around and check for dangling connectors. If not, it could be a 'code' for the airbag, get it back to that dealer.

Oct 05, 2014 | 2004 Mazda MPV

2 Answers

After replacing starter on Mazda MPV,O/D light started flashing,Mech says it could be transmission problem,but the van was running fine before I took it in for repairs.Can you give me any suggestion


someone has broke or disconnected a wire somewhere under the car whilst changing the starter motor ,but what or where i couldnt tell you without having car on the ramp sorry

Nov 13, 2010 | 2001 Mazda MPV

1 Answer

Service engine and airbag lights flash while driving. what is the cause of this?


you can cheak it out for free on http://www.vehix411.com all in video how to reset and diagnose for free

Jan 29, 2010 | 2001 Mazda MPV

3 Answers

Airbag warning lights flashing on dashboard of mazda premacy 52 reg can I reset to clear these lights myself?


there are a quite a few problems associated with the airbag light flashing. The light will flash in long and short frequencies, this is a diagnostic code, e.g. two long flashes followed by six short flashes equals code 26, which is clockspring. Other codes are: 46 and 47 connector under seat, 3 power supply etc.

Nov 17, 2009 | 2002 Mazda MPV

2 Answers

I have a Mazda 2001 MPV, just had service for o2 sensor and now the check engine light is blinking .


blinking light means engine is misfiring. continuing to drive will severely damage the engine. The O2 should not be related to your engine misfiring

Nov 13, 2009 | 2001 Mazda MPV

1 Answer

Four win stuck up for Mazda 2001. fuse is working


I have a 2000 Mazda MPV where the same thing just happened. Unfortunately it came back for a second, and my wife pushed one down. I took it to a glass shop, and found that the driver side power window switch was bad. It runs about $178.00 at the dealership. It takes about 2-3 days to order. Unfortunately not even the import places carry it. I did find a few used on Ebay for about $50-$70.

Aug 30, 2009 | 2000 Mazda MPV

3 Answers

Airbag came on for no reason why 2001 hyundai


call the dealer ship there is a recall on airbags

Jun 14, 2009 | 2001 Hyundai Sonata

1 Answer

Engine light blinking in my Mazda MPV


A BLINKING ENGINE LIGHT INDICATES AN ENGINE CYLINDER IS MIS-FIRING. HAVE THE TROUBLE CODES TESTED TO DETERMINE WHICH ONE. DO NOT DRIVE THIS WAY AT HIGH SPEEDS AS IT MAY OVERHEAT THE EXHAUST SYSTEM AND CREATE A FIRE HAZARD.

May 01, 2009 | 2001 Mazda MPV

1 Answer

SRS


SRS stand for Supplymentary Restraint System, The purpose of the SRS light on your instrument panel is to alert you of a potential problem with your supplemental restraint system. It should blink seven times when you turn the ignition switch to ON or START and go OFF. A possible fault in the system can lead to any of the following: (a) The light does not come on when you turn the ignition ON. (b) The light stays on after the engine starts. (c) The light comes on while you are driving. Apart from the conventional causes of these faults (faulty airbag system), majority of the light indicator problem has been attributed to ignorance while fixing or repairing mechanical and/or wiring systems within the vehicle. If the SRS indicator light alerts you to a problem, have the supplemental restraint system inspected as soon as possible. If you ignore this indication, the airbags might not inflate when you need them. Likely Causes:
  • Steering wheel modifications
  • Faulty driver/passenger seat sensors for your airbag system (located under the seats)
  • Faulty seat belt mechanism
  • Tampered system components or wiring (e.g battery jumpering)
* Sometimes, a little adjustment of your seat belts and/or seat positions might fix the indicator problem over time (if the sensors are not faulty).
Precautions:
  • Do not modify your steering wheel or any other part of the supplemental restraint system. Modifications could make the system ineffective.
  • Do not tamper with the system's components or wiring. This could cause the airbags to inflate inadvertently, possibly injuring someone very seriously.
  • Tell anyone who works on your vehicle that you have a supplemental restraint system. Failure to follow the procedures and precautions in the official service manual could result in personal injury or damage to the system.
  • If all sensors are ok, the system can be reset using appropriate tools; refer to specially trained technicians.
Cheers Fred Omorogbe (reference: https://techinfo.honda.com/rjanisis/pubs/om/PA9696/PA9696A00015A.pdf)

Sep 08, 2008 | 2001 Mercedes-Benz E-Class

Not finding what you are looking for?
2001 Mazda MPV Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...