Question about 1999 Infiniti.5 QX4

1 Answer

1999 infiniti qx4 is not blowing cold air

Hi,my truck is not blowing cold air.The clutch is engaging,the pulley is spinning,and the freons are fine, but no cold air.How do i know the compressor is bad?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Infiniti Master
  • 76,649 Answers

I REALLY DOUBT THE COMPRESSOR IS THE ISSUE HERE. The problem may be the air temperature control blend door actuator motor and/or the blend door is warped and jammed. To replace these componenets it will in most caases require the removal of the entire dash assembly

Posted on Mar 20, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bibleman01
  • 334 Answers

SOURCE: 2001 Infiniti QX4 low beam bulb replacement instructions

Look directly behind the headlight box if there is a rubber sleave covering the plug take it off. Unplug the wires from the bulb, there may be a saftey clip you will have to pry up to get it off.after you get the plug off the bulb holder should twist counterclockwise then it will pull right off.When you change the bulb just remember to wipe your body oil off the bulb before attaching it back into the headlight box. Then plug it back in and your in business. The high beam has three wires and the low beam has two wires. The bulb will have to be the right one.
God Bless You Greg

Posted on Nov 25, 2008

  • 14036 Answers

SOURCE: were can i locate knock sensor on infiniti qx4

located on the bottom side of engine.

Posted on Apr 25, 2009

  • 5 Answers

SOURCE: how much oil does the 1999 infiniti qx4 hold (when

5 quarts

Posted on Aug 06, 2009

  • 312 Answers

SOURCE: Pls where is Swirl Control Solenoid Valve located in Infiniti QX4

This link shows the location of the SCV, If your motor is different the location should be similiar. http://img510.imageshack.us/img510/5687/vacuumdiagramuh3.jpg

There's a vaccuum line that runs off the SCV to the SCV check switch.

P0442: Have you inspected the lines, charcoal cannister etc? Make sure the fuel cap is tight. The easiest way to check the system is to have someone perform a smoke test. I had a DTC on my car which indicated a EVAP problem, it turned out to be the Fuel tank evaporator Control Solenoid.

Posted on Sep 22, 2009

  • 1428 Answers

SOURCE: I have an 1999 Infinity

There can be a misfire too from the cylinders.

An engine that hesitates, stumbles or misfires when accelerating or when it is under load is an engine that is either sucking too much air, not getting enough fuel or misfiring. If the Check Engine Light comes on, you may find any of the following codes:

• P0171, P0174 Lean fuel condition codes
• P0120 to P0124 Throttle position sensor codes
• P0222 to P0229 Throttle position sensor codes
• P0400 to P0409 EGR related codes

If there are no misfire codes, a common cause of acceleration stumble is a bad throttle position sensor (TPS). The TPS tells the computer how far the throttle is open. The computer uses this information to determine how much fuel is needed to maintain the correct air/fuel mixture and when extra fuel is needed if the throttle suddenly opens wide.

Another common cause is dirty fuel injectors. If varnish deposits have built up in the tips of the injectors, they won’t spray as much fuel as they normally do, or will “dribble” fuel instead of spraying a fine mist. This creates a lean fuel mixture and conditions that are ripe for stumble and hesitation (also misfire). Look at short term fuel trim (STFT) and long term fuel trim (LTFT) with your scantool. If the numbers are high, it tells you the engine is running lean and the injectors need cleaning. Treat mild cases with a high quality fuel-injector cleaner additive. Severe cases require professional cleaning equipment.

Also if this sensors apply to your vehicle, camshaft sensor or crankshaft sensor if sensors bad you don't get any spark. Also run a scan on the car.

Good luck and rate this solution, please.

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Solution to a non-engaging AC clutch?


What you need to do is check the air gap in the clutch, if it is to large it will not engage, it can also be adjusted by removing shim washers or removing some thickness off a Washer....

Feb 13, 2016 | 1997 Honda Civic

1 Answer

How to force run the AC compressor to recharge AC in 2001 Infiniti QX4?


this will be a bad move as you are wasting money on a system that has a leak
until you fix that leak the gas is wasted
next by allowing gas into the system , the ac compressor will switch on when the pressure is sufficient
to see of the ac compressor is running simply look at the plate in front of the pulley and if it is spinning ,it is working
best advice , have an accredited ac shop check it out first.

Jun 17, 2015 | 2001 Infiniti QX4

1 Answer

Hi, I have a 2006 Audi A4 2.0T. A/C compressor failed and I replaced it with a new one. Vacuumed the lineset to negative 10 for about 20 minutes. Left it sit to see if it held, all good. Charged the car...


Is the compressor clutch engaging? Negative 10 is NOTHING. You may as well have left it open to the air. It should be as close to 29 as possible. Did you flush the system to remove crud from compressor failure?

Jul 24, 2017 | Cars & Trucks

1 Answer

My 2002 neon's A/C blows warm air. The vent pressure is working well- but it blows warmer than the outside air. Can I fix this myself? What might the problem be?


If you are handy, yes you can. Most likely causes are loss of freon which would prevent the compressor clutch from being engaged and operating the compressor, a lack of 12 volts being applied to the compressor clutch because the a/c compressor fuse or relay has failed, preventing the clutch from engaging the compressor, or the compressor clutch itself failing. Easy test is to watch the compressor pulley with the motor running. The pulley will, of course be spinning, but the circular assembly mounted to the front of the pulley will spin with the pulley only when the compressor is engaged. There is a sensor mounted to the a/c line that prevents the clutch from engaging the compressor if there in not enough freon in the system. You could go to auto zone or checker and buy a can of freon r-134 with a hose for around $15.00. It is fairly easy to follow the instructions to charge the system. If, after allowing some of the can to pressurize the system, the compressor clutch engages then you can continue to charge the system. Cold air should start to blow by the time the can is empty. Or you can locate the a/c relay located in the fuse panel, remove its plastic cover and manually close the contacts while observing the compressor pulley assembly. If the clutch doesn't engage then the problem in probably electrical, a fuse, the relay or the electric clutch itself. Go to auto zone and check you their dvd on a/c repair for under $9.00. Hope this helps! Dano

Jul 01, 2011 | 2002 Dodge Neon

1 Answer

Why won't the clutch engage on the ac but the pulley spins fine. 1999 Grand Prix GTP 3800 supergarged


not swich on
burnt fuse
faulty relay
faulty relay swith
faulty clutch coil
empty or low freon

Jun 09, 2011 | 1999 Pontiac Grand Prix

1 Answer

My 2002 Expedition air conditioner will sometimes blow hot air and others cold air


I would check the following possibilities:
1. Is compressor clutch working? - You need to do this when the ac is blowing hot air only - locate compressor drive pulley on engine - rubber belt wraps around it. Start engine and set to max ac. When the ac is blowing hot air, look at the center of the compressor drive pulley using a good flash light - watch it for a while, it should be spinning with the pulley - this means the compressor is engaged. If not, the compressor is not engaged. If your ac is blowing hot air, then the compressor should be engaged and running (trying to cool). If it is not engaged, then your compressor clutch is probably going out. Could be low voltage to clutch, but more likely the clutch is worn out and only working some of the time. Note: if working normally, the compressor clutch will engage and disengage in cycles- but the air should always be cold. If clutch is bad, compressor would need to be replaced (sold as one unit). This is tricky to diagnose and could take some time - you need to do it when ac is blowing hot air but set to max cooling.

2. Low on refrigerant or refrigerant has moisture in it? If your ac blows cold initially after being off for a while, then heats up, and continues to regularly cycle back and forth between hot and cool air, then the system may be low on refrigerant or the refrigerant may have moisture in it that is freezing and restricting refrigerant flow. An a/c shop can check refrigerant level and even replace refrigerant if moisture is suspected.

Could be other issues, but I would start with these.

Good luck

May 07, 2010 | 1999 Ford Expedition

3 Answers

No Cold air from 99 Montero Sport


replaced clutch, driver ac belts on 2000 montero sport a/c is still not blowing cold any ideas

Jun 30, 2009 | 1999 Mitsubishi Montero Sport

1 Answer

A/c stopped working,the clutch still engages, fan blows warm, found no fluid leaks


the air blend door inside the heating / cooling unit that sits under the dash is probably not moving. there is an electric motor and control unit that moves the air blend door (assuming you have the electric dial or push button digital controls. some of these vehicles have a valve that shuts off the antifreeze from cycling through the heater and if it remains open then you would get "not hot" but just warm air.

Apr 26, 2009 | 1999 Infiniti.5 QX4

1 Answer

Screeching noise, then a/c stops blowing cold air. Still blows air, just not cold air.


it could be the air conditioning clutch going out. to check turn your car on and idle it with ac on and hood open. at the ac compressor it will have a pulley on it with a clutch that engages when the air conditioning is on. if it engages and disengages it can be the clutch itself has gone bad, the ac clutch will also disengage if there is not enough freon in the ac system, will also engage and disengage if the pressure gets too high in the ac system. Depending on the year of the vehicle it will disengage at full throttle and come back on when you are not at full throttle.
If it is a metallic sounding screech for example take a coke can and drag it across pavement kind of sound it could be a bad compressor or a bad ac clutch. If it is a more rubbery sound for example a car spinning its tires kind of noise it could be a loose belt.

1. Check to make sure all belts are tight under hood
2. start car and look at ac compressor to make sure compressor pulley is turning and that the fan clutch is engaged spinning


Aug 09, 2008 | Mercedes-Benz 400-Class Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...