Question about 1992 Ford Ranger

1 Answer

92 ford ranger i turn the wipers on and only here clicking why?

When i turn on wiper blades they do not work but i here a clicking noise wiper washer works fine the clicking goes faster when i put it on a higher setting whats wrong?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Ford Expert
  • 150 Answers

Just guessing, but sounds like the rod that connect the wiper motor to the wipers has broken or the just a clip came off the wiper arm. You can see the wiper arm through the cal panel in front of the windshield. If not, the cal panel will have to be taken off to get to it. Good luck.

Posted on Dec 14, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
gregstobbe
  • 56 Answers

SOURCE: I have a1992 ford explorer the front and rear wipers quit workin

check for power at the wiper motor. If power at the wiper motor but no wiper action then replace the motor. if no power at the motor then use a jumper wire and put power to the motor. Does motor run? if so check for open circuit in the wire someplace.

Posted on Dec 27, 2008

moparownr
  • 667 Answers

SOURCE: wiper motor quit working

does the motor not run? check the operation rods connected to the arms and the motor, see if they are bent

Posted on Apr 07, 2009

Nomodo4u
  • 863 Answers

SOURCE: 2002 ford ranger wiper problem replaced wiper

Check for blown fuses or go outside and turn the wiper on and see if you can hear the wipers trying to move.  The bushings under the wiper arm might be stripped or not properly aligned.  You might have a short somewhere also.  Electrical problems can get expensive.

Posted on Oct 30, 2009

bulldogchief
  • 388 Answers

SOURCE: Removing/replacing wiper motor in '93 Ford Ranger

You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

Posted on Nov 09, 2009

01fordeb
  • 1033 Answers

SOURCE: 1998 ford expedition front windshield washer

fuse for washer pump, can you here the pump, if not then power to pump isn't present. Check the fuse for it.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reattach wiper arms on my ranger


Video says almost all (ranger/explorer similar)...
How To Install Replace Windshield Wiper Blades and Arms Ford Explorer...


https://www.youtube.com/watch?v=c-tR49oL1FQ

May 11, 2015 | 1999 Ford Ranger SuperCab

1 Answer

1994 ranger wiper not working, just making a clicking noise


check the wiper motor gears. sounds like its slipping, may be a plastic gear

Dec 15, 2012 | 1987 Ford Ranger

2 Answers

Can't find wiper relay on 94 ranger


Wipers do not require a relay. If your wipers are not functioning and a fuse is blown, the washer will not work either. If the washer works, check the wiper switch or the wiper motor, but wiper motors are normally very reliable.

May 17, 2011 | 1994 Ford Ranger Supercab

1 Answer

How do I change my wiper blades on my '92 Crown Vic? Do I have to change the whole wiper arm?


Most auto parts stores will gladly change out the blades for you. As far as your question.......No, you only have to replace the blades and not the completer wiper arm.
Hope this helps

Aug 26, 2010 | 1992 Ford Crown Victoria

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Removing/replacing wiper motor in '93 Ford Ranger


You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

Nov 09, 2009 | 1993 Ford Ranger SuperCab

1 Answer

I cant figure out how to change my windshield wiper blades on 2001 ford ranger


How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 16, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

How do I replace the right transmission arm from wiper motor 92 R


see if you have a nut on the top of the wiper are that has stripped off. there are splines that hold them on and the arms are both connected to each other. you would need replace the whole assembly that connects to the motor.

Sep 03, 2009 | 1992 Ford Ranger

1 Answer

1992 ford ranger wiper wont work wiper pump not working fuse ok?


check wire continuity with multimeter, have had switch go out on ranger as well.

Apr 05, 2009 | 1992 Ford Ranger

Not finding what you are looking for?
1992 Ford Ranger Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...