Question about Ford Ranger

1 Answer

I have a 1987 ford ranger the battery is good but I don't have any power anywhere else

No power at all

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 37 Answers

Start with the battery cables and check voltage.

Posted on Mar 31, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 40 Answers

SOURCE: 1987 2.9 ford ranger 4x4 no spark.why am i not

new spark plugs probobly. get them tested first by a proffesional. take them out and show them to somebody at like a kragen and they should tell you

Posted on Aug 07, 2009

  • 1129 Answers

SOURCE: 1987 Ford Ranger stuck in 4 wheel drive!!

Chances are the linkage for the transfer case is out of adjustment try loosening the adjuster bolt and put the 4WD shifter into the position 4WD high or low (depending upon which position it's lockup in) then lock down the adjuster bolt, try to shift out of 4wd sometimes you need to go forward and backward with the vehicle to get it out of 4wd, when you get it out of 4wd you may have to fine tune the adjustment to get it to engage and disengage smoothly it's a trial and error thing keep resetting adjuster until you get the desired effect.

Posted on Jul 02, 2009

  • 2920 Answers

SOURCE: 1987 ranger

check the crankshaft sensor

Posted on Jan 19, 2009

  • 27 Answers

SOURCE: 1987 ford ranger 2.9 liter v6 runs good, then just

check for a brown or green relay under hood, relay will be marked eec relay, or fuel relay. replace both of them relays and your troubles should go away

Posted on Aug 15, 2009

dennymulford
  • 1055 Answers

SOURCE: 2000 Ford Ranger. No power anywhere, new battery

check the body ground and fuesable link!!!

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power to fuel pump when key is on 1987 ford ranger


ck the inertia switch located on the foot wal under the carpet

Sep 11, 2014 | 1987 Ford Ranger

1 Answer

What kinds of battery for 1987 ford ranger?


http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c152800781b2 Here's a link to your electrical diagram,check the fusible links on the positive side,it shows 3 of them,check for burnt or melted wiring.

Sep 07, 2012 | 1987 Ford Ranger

1 Answer

I have a 85 ford f250 with the 351. the truck starts fine, but dies after a while. so I pulled the battery wire while it was running and the thing died. so I replaced the alternator. that did not solve the...


First off you don`t want to disconnect the battery when the engine is running as that will damage the alternator.Ford had a problem with the electonic module on some of engines in 85.good luck

Dec 14, 2010 | 1987 Ford Ranger

1 Answer

I have a 1987 auto trans for ranger & it nee s to be move. how can i move it without starting it? or is it possible?


Remove the drive shaft by removeing the four bolts at the rear U joint. After you remove it you can move anywhere you want

Apr 21, 2010 | 1987 Ford Ranger

1 Answer

Where is the solenoid on 1991 ford ranger?


Find the battery,look at the positive battery cable.Follow the positive battery from the battery to the solenoid,should be on right fender well.

Mar 07, 2010 | 1987 Ford Ranger

1 Answer

2000 Ford Ranger. No power anywhere, new battery


check the body ground and fuesable link!!!

Mar 04, 2010 | 2000 Ford Ranger SuperCab

2 Answers

How to hot wire a 87 ford ranger 2.9 4x4 fuel pump?


got 1987 ford f-150 no power to fuel pump, checked fuel cut off swith seems ok, new fp relay still nothe can I run hot wire to pump and if I can which ones the hot wire??

Dec 28, 2009 | 1987 Ford Ranger

1 Answer

1987 2.9 ford ranger 4x4 no spark.why am i not


new spark plugs probobly. get them tested first by a proffesional. take them out and show them to somebody at like a kragen and they should tell you

Aug 07, 2009 | 1987 Ford Ranger

1 Answer

1987 ranger will turn over no spark anywhere replaced engine computer


It could be the ignition module. I have seen that go bad. I like my Chilton book, it helps a lot.

Apr 29, 2009 | 1987 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...