Question about 2000 Chrysler Grand Voyager

1 Answer

Missing petrol cap

Now i know im an idiot..i still can't believe that i did this..put petrol in my car and i forgot to put the petrol cap back on.. where can i buy a new or 2nd hand petrol cap and how much would it cost me? Please tell me it wont be that expansive :( Thank you so much..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Chrysler Master
  • 1,249 Answers

Most drivers have done this before...:) As you refer to the gas cap as a "petrol cap", you must be from Europe? Factory replacement caps are available at most auto parts stores. Locking caps are optional. These are specifically vented, so it is best to ask the parts rep for the correct model for your car...About $10 US dollars:) You can also find your cap on line "Auto Parts" ...Hope this helps.

Posted on Mar 20, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

clifford224
  • 1975 Answers

SOURCE: I know how to find

As the distributer is being slid in, it will rotate some. You want to slide it in and as it rotates you want to align the rotor to where the number 1 spark plug wire will go. I don't know if you have the 4 or 6 cylinder:
1999 Chrysler Sebring
2.5 liter SOHC V-6 VIN "N" 92761702.gif 1999 Chrysler Sebring
2.0 liter DOHC L4 VIN "Y" 92729417.gif

Posted on Jan 30, 2011

  • 3640 Answers

SOURCE: i believe im having a

the rotten egg smell is a catalytic convertor going bad. here are a few symtoms.--- you should notice a drop in power and also a higher running temperature,also at night you may notice a slight glow from this thing if its heating up,it will also loose power ,on any kind of a hill or small incline it may idle rough from time to time also,there are several warning signs of one going bad ,if your in doubt about it,you can have it checked,they can drill a hole in it and check the back pressure on it,this will tell you if its going bad,this is actually the best way to check it out. have a good day !!

Posted on Mar 11, 2011

  • 496 Answers

SOURCE: I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack

Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

Posted on May 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...
2000 Chrysler Grand Voyager Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...