Question about 1999 Isuzu Rodeo

1 Answer

How do I remove the cv axle in a ford telstar 1993 - both sides

I've removed the outer cv joint on one side but am having trouble getting it back on past the circlip. Any suggestions on how to get the outer back on without removing the axle or how to remove the whole axle??

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 42,190 Answers

Line the outer up in the right place and enter it until the circlip is against the splines . Use a large heavy hammer and rap the end of the shaft hard and the circlip will pop in the groove and allow the shaft to go home.. Removal from the shaft is much the same as it has a circlip inside the transmission. So remove the shaft from the wheel. Use a hammer to hit the cv joint so that it jumps the shaft out of the transmission .

Posted on Mar 20, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: '93 Isuzu Rodeo, CV Joint replacement.

unbolt the tie rod end and the lower a arm and it should slide out of there

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the front left axel shaft on a 1993 buick park ave.


Basically, jack up the vehicle and support it on jack stands, remove the nut on the end of the axle, outer tie rod end and ball joint. Split the tie rod end and ball joint from the spindle assembly. Gently tap the end of the axle to loosen from the wheel bearing assembly. Once loose pull the spindle assembly outward while pushing in on the end of the axle. Once the axle is free from the spindle housing. Will need to apply gentle pressure on each side on the inside CV joint to get the axle to release from the transmission. There is usually a "C" snap clip on the end of the axle in the transmission which may make it a little stubborn to get out. Be sure to not damage the seal where the axle goes into the transmission or you will have a leak

Oct 17, 2014 | 1993 Buick Park Avenue

1 Answer

How do I remove my old cv axle on my 97 mercury mountaineer?


remove the brake caliper and rotor then undo the axle nut and disconnect the lower ball joint and separate from the spindle assembly. pull the outer cv joint out from the spindle and pull out the half shaft. you may have to remove the speedometer drive gear before removing the half shaft. installation in reverse order.

Sep 15, 2014 | 1997 Mercury Mountaineer

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

Ford focus - clunk in driveline in reverse when wheels are lock left or even right


Drive Axle CV Joint is bad
You will need to replace the complete drive axle,on one side of the vehicle,and inspect the other side as well
You will be getting a rebuilt part.
I believe, when you turn the wheels and back up ,it is the outer joint.

May 09, 2010 | 2001 Ford Focus

1 Answer

Rt front axle broke how to repair


If there is no other damage aside from the outer CV joint being out.

1. Jack car up and support on jack stand on the affected side.
2. Remove wheel
3. Remove center hub nut
4. Turn wheels all the way to one side or the other. This is to gain access to the lower ball joint. One way will be easier than the other depending on how the bolt is installed.
5. Remove lower ball joint bolt and nut
6. Separate the ball joint by using a large pry bar or pipe to push the control arm down and hit side of joint with hammer.
7. Once joint has released pry down to free control arm from ball joint shaft.
8. Now tap the outer cv joint part still trapped in the hub out
9. Remove remaining axle from transmission by using a pry bar to pry it out of the transmission.
10. Reinstall new axle into transmission and then start into hub. Make sure to shove axle firmly into transmission so as to get past the C-clip lock.
11. Pry lower control arm down to allow the ball joint to be reassembled. Slip ball joint shaft back into control arm.
12. Reinstall bolt and nut
13. Install hub nut
14. Install wheel

Jan 24, 2010 | 1994 Pontiac Bonneville

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

2 Answers

How do I remove the outer CV joint from the axle?


After removing the axle assembly, clip the metal band on the large side of the rubber grease boot, slide the boot back on the axle shaft. Pull the outer CV housing and axle stub away from the CV joint. You will find that there is a circlip holding the bearing carrier onto the axle shaft, remove it. Remove the boot.

Installation is the reverse of removal.

Dec 26, 2009 | Mazda 626 Cars & Trucks

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

Ford festiva cv boots


Depending on mileage and how long you have driven with a damaged boot, it may be a good idea to swap in a new axle ( re manufactured). If you are handy enough to get the axle out, you should be able to get the old joint apart by putting the axle in a vise, cutting off the old boot, and removing the joint from the axle. There are various ways that these are fastened, but generally they are held in place by a circular clip or retaining ring. Check a manual for your specific type of retainer. Once removed, the joint should be completely disassembled and cleaned in solvent, and then reassembled. Then, you still have an old joint, which is why it is faster and easier and better to replace the axle. Good luck. Chip

Dec 15, 2008 | 1993 Ford Festiva

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...