Question about 2007 Jeep Wrangler Unlimited Rubicon 2 Doors

1 Answer

REMOVING STOCK SHIFTER FOR 4X4 ON 07 WRANGLER

REMOVE 4X4 SHIFTER

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

The 4WD shifter knob on the 2007 JK's is ridiculously hard to remove. Pull straight-up with all your might, then after that fails, get some towels, and a chunk of would with a long pry bar. Hopefully you won't crack your center console.

Posted on May 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the shifter from the transmission on a 02 jeep wrangler


A/T or M/T
auto or stick?

mine a stick. why do that.?

Aug 03, 2014 | 2002 Jeep Wrangler

1 Answer

Replace ignition switch on 99 jeep wrangler


The ignition key must be in the key cylinder for cylinder removal. The key cylinder must be removed first before removing ignition switch.REMOVAL 1. Disconnect negative battery cable at battery. 2. If equipped with an automatic transmission, place shifter in PARK position. 3. Rotate key to ON position.4. A release tang is located on bottom of key cylinder.5. Position a small screwdriver or pin punch into tang access hole on bottom of steering column lower cover.INSTALLATION 1. If equipped with an automatic transmission, place shifter in PARK position. 2. Position key cylinder into steering column as it would normally be in the ON position. 3. Press key cylinder into column until it snaps into position. 4. Check mechanical operation of switch. Automatic Transmission: Be sure transmission lever is locked in PARK position after key removal. If key is difficult to rotate or is difficult to remove, the shift lever-to-steering column cable may be out of adjustment or defective. If key can be removed, release lever mechanism may be defective. Release lever mechanism is not serviced separately. If repair is necessary, the steering column must be replaced. 5. Connect negative cable to battery. 6. Check electrical operation of switch. ab7076e7-9719-44a3-b66a-8584c6b2a3c1.jpg bfaa43e6-23a3-4771-9d95-55c2c3bf0a78.jpg

Apr 08, 2014 | 1999 Jeep Wrangler

1 Answer

My jeep wrangler 2008 - I shifted to reverse then to parking, when i release the breaks it kept going in reverse. So i turn off the engine. now it wont start the engine, neither the shifter will move


The shifter cable has broken more than likely ,Find the shift shaft on the transmission,,block the wheels and remove the shift cable from the shift shaft,put the gear shift in park,then shift the shift shaft in park,then it will start,Then of course you will have to replace the shift cable.

Oct 05, 2013 | 2008 Jeep Wrangler

1 Answer

I have a 95 jeep wrangler yj and no 4wd. when i put the shifter into 4wd (hi or low) the indicator light comes on but i get no power to the front wheels. any ideas?


Check the vacuum disconnect on the front axle. After 15 years, the lines break and/or get clogged. I have seen a few of the shift forks in there broken on Jeeps still wheeling with the stock Dana 30. There is a cable option which replaces the vacuum system if you dont want to worry about having the problem again. check Quadratec or 4WD hardware.

Dec 05, 2010 | 1995 Jeep Wrangler

1 Answer

Four wheel drive hangs up after disengaging


Are you lifted or stock height? The 4 wheel shifter linkage hanger is located on the drivers side front tranny tunnel (to the left of the 4wd shifter on the floor). This linkage can come loose or gather a bunch of dirt/debris. The only way to tell is to get under and take a peak.

If you are lifted and didn't install and extension bracket, the linkage will bind.

GL!!

Feb 09, 2010 | 1999 Jeep Wrangler

1 Answer

How to install a B&M short throw shifter on a 91 jeep wrangler YJ. Is it necessary to lower the transmission to install new shifter? Have already removed shift lever


No, There is no modifications of that sort to install a shifter if you have the application correct.. Oops, you mean remove? Still no. The floor should have a removable pan on the hump above the trans.

Nov 09, 2009 | 1991 Jeep Wrangler

1 Answer

2009 Jeep Wrangler - 4WD shifter linkage (problem & solution)


They acually have an Rapid response for this. This should have been replaced before the car was even sold.

Oct 05, 2009 | 2009 Jeep Wrangler

1 Answer

88 wrangler wont shift


Clutch pedals have a safety interlock switch that keeps a manual transmission vehicle from starting. It sounds like the pin on the bottom of the shifter in the trans is getting worn and needs to be replaced. You can remove the boot on the shifter and the cover on top of the trans and see the pin. It's a simple matter of getting the pin out and installing a new one. Just make sure everything lines up good on the install and everything is clean. Another thing that may be the culprit are the synchronizer plates could be worn nearlt out. To replace or fix this you will need the trans out of the vehicle and tear it down. Start with an inspection of the pin and the linkage as well, then if it doesn't work correctly then you may have to tear into it.

Jun 19, 2009 | 1999 Jeep Wrangler

2 Answers

1991 Jeep Wrangler Stuck In Gear


check the linkage from gearstick to gearbox

Apr 05, 2009 | 1991 Jeep Wrangler

1 Answer

'99 wrangler has trouble shifting to 2nd gear - 4th gear occasionally slips to neutral


If you can see where the shifter goes through the floorboard, make sure the shifter is not hitting the floor.
There could be interfierence under the car also.

Oct 24, 2008 | 1999 Jeep Wrangler

Not finding what you are looking for?
2007 Jeep Wrangler Unlimited Rubicon 2 Doors Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...