Question about 2009 Daihatsu Sirion 1.0

Open Question

Changing bulbs how do you change tail light bulbs? i removed the 2 screws but i could not remove tail light seems stuck in place. is it glued or is there another screw somewhere else .

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 209 Answers

SOURCE: Tail Light Removal on 03 Charade

Open the trunck and pull the carpet away from the side you are doing and you got easy access to the tail light

Posted on Apr 17, 2010

Ad
  • 1 Answer

SOURCE: Tail Light Removal on 03 Charade

Daihatsu Charade EL 2003 rear lens removal. Open the tailgate and remove the two bolts securing the lens assembly. Then get a good hold of the lens and pull out. You need to pull out the whole lens assembly since there are three plastic protruding 'clips' on the side along the lens. Please view attached pictures. Then turn the bayonet bulb holder, replace the slide on type bulb and reassemble everything back in place.
4_18_2015_5_22_46_pm.jpg4_18_2015_5_22_47_pm.jpg

Posted on Apr 18, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

How to fix mitsubishi eclipse tail lights


open the trunk. locate the plastic screws that hold the carpeting in place at the top of the trunk. remove one or two of the screws nearest to the tail light by simply pulling them straight out so you can pull back the carpeting in the trunk. now you will be able to see the screws holding the tail lights in place. remove them using a wrench to loosen the bolts, making sure you remove all of them, there should be four or so. use a flathead screwdriver end to gently remove the tail lights. now you are free to change the bulbs by twisting the plastic caps for removal from casing to expose the bulbs or you can unplug the tail light and install a new one making sure to add the bulbs to the new unit. thread wiring through loops and you're done. would be helpful to ensure all are working before reassembling. repeat process on other tail light if necessary.

Feb 04, 2012 | 2001 Mitsubishi Eclipse

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

2 Answers

Changing a rear turn signal bulb


in a lot of cases on modern motors i just remove the whole light ,its easier most of the time and this is a pick up so the chances are it sealed light and access can only be gained by removal

Jun 26, 2010 | 2004 Chevrolet Silverado

1 Answer

I can't seem to get the tail light off to change the bulb, how do I do this


Open the rear tailgate and remove the two screws that hold the tail lamp assembly in place.Now there are two alignment pins that hold the lamp in place, you must use a screwdriver or other flat device and lightly pry the lamp your working on. If you are removing the rear left (driver side) then pry back outward to the left. Alternately, if you are removing the right rear tail light, pry outward to the right. Do not try and pull directly back. The pins will prevent the light from coming out. You have to pull left or right, depending on the light your removing. Good luck.

Jan 05, 2010 | 2002 Isuzu Axiom

2 Answers

Change lens cover1998 grand caravan


There's really no way to change a lens cover on a headlamp or tail light on that vehicle. You'll have to change the whole light/housing. For the tail light, open the hatch and remove the two screws. Depending on weather you buy new or used, you may have to replace the board on the back. For the headlight, open the hood. There are two 10mm bolts on the top and two that come straight in from the back. On the driver's side it might be easier to take out the battery. Be careful though, these bolts have a tendency to break easily. Unplug the bulbs. If you remove the bulbs, be careful not to touch the glass on the headlights as these are usually halogen bulbs. The oil on your fingers will create a "hot spot" causing the bulbs to fail soon.

Jun 29, 2009 | 1998 Dodge Caravan

3 Answers

How do I change brake light bulb of Nissan Sentra 2008


Was able to complete this job successfully:
It's a little tricky to do without pictures, but I don't have any available right now.
  1. Access the trunk
  2. Remove the material covering the light. You'll need to remove the black pegs by lifting the centre part. A flathead screw-driver will help. There are 2 to remove -- one directly behind the brake light and another at the top of the trunk.
  3. Pull back the material to expose the brake light wiring and the metal frame of the car.
  4. There are 2 nuts / screws to remove near the entrance of the trunk. Both are about 4 inches apart and hold the tail light's cover in place. Remove both.
  5. Using a bit of force, you will be able to pull off the entire tail light from the frame of the car. This is done on the exterior of the car.
  6. Rotate the problematic light from it's housing (it should come off with ease) and pull it out of the socket. Brake light and indicator are a 3057K bulb.

Jun 21, 2009 | 2008 Nissan Sentra

2 Answers

Rear blinker light change 2001 ram1500


Hello
Welcome to FY
open the tale gate look at the side where the light is there is 2 screw that hold the light to the box
RD

Jan 10, 2009 | 2001 Dodge Ram 1500 Truck 2WD

3 Answers

How to access brake tail light to change


Tail light replacement is not as hard as it seems.
Tools needed:flat head screwdriver and a deep 5/32 socket(a pair of pliers will work).
Step 1: open trunk and pull back truck liner at tail light.There is a small button clip on liner.Use screwdriver to pop up the center of button clip,pull clip out of hole.
Step 2:You will see a black wire attached to the body of car with 2 white clips.Use screwdriver to pop clips off of studs.
Step 3:Remove the nuts from the studs and pull tail light assembly straight back away from car.The outer side of the light just snaps in and out of place.
Step 4:Turn light socket counter clockwise 1/3 turn and pull out.
Step 5:Pull bad bulb straight out and replace.Reverse steps to reassemble.

Oct 24, 2008 | 2007 Nissan Sentra 2.0 SL Sedan

2 Answers

Changing brake bulbs


Open the back gate of the jeep. There chould be 2 screws that hold in the light assembly. Remove the screws and pull out the assembly. Replace the bulbs and replave the housing.

Jul 20, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2009 Daihatsu Sirion 1.0 Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...