Question about 2006 Volkswagen New Beetle

1 Answer

How to get water from rear light assembly

I have water in my rear light assembly is there an easy way to remove without switching in out

Posted by on

Ad

1 Answer

Have to remove the lamp assy & find where the water gets in,
then blow it out with an air hose,let it dry & try to glue it

I read where the only fix is to replace the lamp assy
I would try glueing it first

Posted on Mar 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Back brake light stay on, replaced brake switch same problem.Truck has over drive and cruies control If you take switch out of circuit the brake lights stay on the same with the turn/hazard flasher.


Your brake lights and your turn signals go through the multifunction (turn signal) switch. It is common for these switches to short internally. Partial disassembly of the steering column is required to replace it. The airbag stsyem must be disabled, then the airbag removed from the steering wheel. Then the steering wheel must be removed to access the screw in the front of the switch assembly. The rest is pretty easy... a few screws holing the lower cover of the dash, the shroud around the steering column and a few connectors to deal with. (see pictures of switch assembly below)
There are two types of these switches available for 2000 S-10. With cruise control and without cruise control. The one WITHOUT cruise control is much more expensive!


dttech_156.gif
dttech_35.jpg

Aug 06, 2011 | 2000 Chevrolet S-10

2 Answers

Harrismk@How do I remove the rear tail light plastic cover to get to the light bulb?


You don't. The method involves removing the entire assembly and the bulbs go in from the back. This makes for much more water tight trunks.
You need to release interior trim to get at the 3 or 4 thumb screws to release the assembly. Pretty easy job, once you know where to go.

Oct 27, 2010 | 2000 Buick LeSabre

1 Answer

Replace passenger mirror


glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.
  1. Remove the front door trim panel; refer to Section 501-05.
  1. Remove the outside rear view mirror access water shield.
    gn1881a.gif
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect and remove the speaker.
    gn1882a.gif
  1. Disconnect the outside rear view mirror electrical connector.
    gn1883a.gif
  1. Remove the outside rear view mirror.
    1. Remove the nuts.
    1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.
    gn1884a.gif

Oct 26, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Remove a rear tail light assembly & install a new one


Open the hatch (or trunk if it's a convertible) and peal back the back the trim against the rear most panel. You'll be able to see a lot of large plastic wing nuts. Unscrew them and pull the lense straight out.

Jul 14, 2010 | 2000 Chevrolet Camaro

1 Answer

How do I remove the rear light assembly on a 2008 A6 S-Line


Drill a tiny hole in the lense , where the water is gathering take lense piece out let dry ,fill hole with small amount of silicone rubber,clear,walmart has it in hardwear/paints .

May 02, 2010 | 2008 Audi A6

1 Answer

The left break light sensor comes on and off on the car indicator and will cause the three pack of lights to go out also this will happen with the right side of my 2003 bmw 325i with 45K


water in the rear brake light assemblies. common problem. remove the brake lite assembly------very very easy thing to do. there are three nuts holding it in from inside the trunk. once they're off the whole assembly just pops out. then it can be cleaned. usually the rubber gasket around the assembly leaks water into the lights and messes up the contacts where the bulbs screw into the circuit board.

Nov 03, 2009 | BMW 325 Cars & Trucks

1 Answer

Replace right rear break light


PLEASE DON'T FORGET TO RATE!!!

Signal & Marker Lights Removal & Installation Rear Lamp Assembly Sedan To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the luggage compartment quarter trim panels.
  3. Disconnect the rear lamp assembly electrical connector.
  4. Remove the lamp assembly mounting nuts.
  5. Pull the lamp assembly away from the body.
  6. Disconnect the rear lamp assembly bulb connectors.
  7. Remove the rear lamp assembly.
6753524.gif
To Install:
CAUTION
To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.
  1. Position the rear lamp assembly near the body and connect the bulb connectors.
  2. Install the lamp assembly into the body.
  3. Install the lamp assembly mounting nuts. Tighten to 53 in-lbs (6 Nm).
  4. Connect the rear lamp assembly electrical connector.
  5. Install the luggage compartment quarter trim panels.

Jul 16, 2009 | 1998 Ford Taurus

1 Answer

Right rear signal light needs replacing


you need to remove the lamp assembly to replace the bulb. here is the procedure:

Rear Lamp Assembly —Sable Four Door Removal and Installation
  1. Remove the luggage compartment scuff plate.
  1. Pull back the luggage compartment carpet.
  1. Disconnect the rear lamp assembly electrical connector.
  1. Remove the nuts.
04eb075.gif
  1. Remove the rear lamp assembly.
    1. Pull the lamp assembly away from the body.
    1. Disconnect the rear lamp assembly bulb connectors.
    1. Remove the rear lamp assembly.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.
    To install, reverse the removal procedure.

Jun 25, 2009 | 2001 Mercury Sable

2 Answers

Need help for rear tail light assembly on my 2003 trailblazer


Most of the time you can simply remove the tail light assembly from the car pretty easy and just a few screws. If it sdoes not have the screws going through the front of the housing then its rear mount and must be done by lifting the tailgate to get access. Once in the vehicle you should beable to remove the plastic housing covering up the assembly from the inside. Remove the 3-4 screws or bolts and the tail light assembly. Install the new one just the reverse. Pretty easy just take your time.

Joe

May 28, 2009 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
2006 Volkswagen New Beetle Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...