Question about 2002 Chevrolet Monte Carlo

1 Answer

2002 monte carlo, the bolt holding the harmonic balance to crank shaft, it is left of right handed threads

Crankshaft keeps tuning when trying to remove

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Use a wedge in the fan belt to lock the harmonic balance from turning.

Posted on Mar 20, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1403 Answers

SOURCE: chevy 6.6 turbo diesel 2005 harmonic balancer bolt

clockwise

Posted on Aug 13, 2010

airjer995
  • 5332 Answers

SOURCE: the bolt that holds the

it will be a normal right hand thread.

Posted on May 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Which direction do i turn the harmonic balancer bolt to remove it on a 1997 honda civic 1.6 liter


Hi:
The harmonic balancer bolt is a normal bolt with right hand threads, so you need to turn it counter-clockwise.
The hardest part of the process is to keep the crankshaft from turning. An impact wrench is the easiest way to go, but if you don't have one, you can use a large strap wrench or chain wrench to hold the harmonic pulley. I use a section of an old belt to protect the pulley.

Aug 03, 2014 | 1997 Honda Civic

1 Answer

How to replace crankpully on 3300 olbs


The harmonic balancer on these engines is now press fit onto the crankshaft and requires the use of Tool J-38197 for removal. The torque specification to be used during installation has also been revised. The procedure to be used when replacing the crank sensor is as follows:

REMOVAL






  1. Disconnect serpentine belt from crankshaft pulley.


  2. Raise vehicle on hoist.


  3. Remove right front tire and wheel assembly.


  4. Remove right inner fender access cover.


  5. Using 28 mm socket, remove crankshaft harmonic balancer retaining bolt.


  6. Remove crankshaft harmonic balancer using Tool (J-38197).


  7. Remove foreign object deflector (DO NOT use pry bar).


  8. Disconnect sensor electrical connector.


  9. Remove sensor and pedestal from block face.


  10. Remove sensor from pedestal




INSTALLATION






  1. Loosely install crankshaft sensor on pedestal.


  2. Position sensor with pedestal attached on Tool J-37089.


  3. Position tool on crankshaft.


  4. Install bolts to hold pedestal to block face, torque to (18-26 lb. ft.).


  5. Torque pedestal pinch bolt to (26-44 lbs. in.).


  6. Remove Tool J-37089.


  7. Install foreign object deflector.


  8. Place Tool J-37089 on harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.


  9. Install balancer on crankshaft.


  10. Apply thread sealer GM #(NNN) NNN-NNNNor equivalent to threads of crankshaft balancer bolt. Torque bolt to + 56 degrees (104 lb. ft. + 56 degrees).


  11. Install inner fender shield.


  12. Install tire and wheel assembly. Torque lug nuts to (104 lb. ft.).


  13. Lower vehicle.


  14. Install serpentine belt.
see this vedio

Jul 11, 2014 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Is the crank shaft pulley on a renault 1.5 megane left/ or right hand thread


They'd be right hand threads-regular threads-to loosen, turn counter clockwise. An air impact wrench is best for removing the crank bolt. Or a long breaker bar and socket on the bolt, if you can hold the crankshaft stable so it doesn't turn backward with pressure on the bolt. You can pull the starter off, and wedge a big screwdriver or prybar against the flywheel's ring gear teeth, then turn the bolt with the breaker bar.

Jul 13, 2012 | Renault Megane Cars & Trucks

1 Answer

Can't get the crank pulley loose. is it left our right threads. i am replacing the water pump.


TURN CRANKSHAFT BOLT COUNTERCLOCKWISE TO LOOSEN. YOU HAVE RIGHT HAND THREADS.ENGINE TURNING CLOCKWISE.YOU NEED A STRAP WRENCH HOLD CRANKSHAFT PULLEY WHILE LOOSEN IT.BUT YOU NEED A CRANKSHAFT DAMPER REMOVAL TOOL.OR HARMONIC BALANCER REMOVAL TOOL.YOU NEED STRAP WRENCH TO HOLD CRANKSHAFT PULLEY WHEN TIGHTEN IT.TORQUE CRANKSHAFT PULLEY BOLT 90 - 98 FT LBS. MAKE JOB EASIER.HAVE A HELPER HOLD STRAP WRENCH WHEN YOU LOOSEN OR TIGHTEN CRANKSHAFT PULLEY.

Sep 19, 2010 | 1995 Mercury Villager

1 Answer

Crankshaft sensor on a Monte Carlo 2001 SS 3.8 where is this on the car and how to replace it?


3.8L Engine
  1. Turn OFF the ignition.
  2. Remove the serpentine belts from the crankshaft pulley.
  3. Raise the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the right inner fender access cover.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  8. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  9. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  10. Disconnect the sensor electrical connector.
  11. Remove the attaching bolts from the crankshaft position sensor.
  12. Remove the crankshaft position sensor from the block face.
To install:
  1. Position the crankshaft position (CKP) sensor to the block.
  2. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  3. Reinstall the crankshaft position sensor shield.
  4. Connect the CKP sensor electrical connector.
  5. Position the crankshaft harmonic balancer on the crankshaft.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  8. Install the right inner fender access cover.
  9. Install the right front wheel and tire assembly.
  10. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  11. Lower the vehicle.
  12. Reinstall the serpentine belts.

It looks like this:

fd368a5.jpg

Jan 10, 2010 | 2001 Chevrolet Monte Carlo

2 Answers

Daewoo Matiz crankshaft pulley


remove the outer small bolts to remove balancer(pulley) the big centre bolt holds crankshaft gear for timming belt which slides off with timming belt removed.

Sep 10, 2009 | Daewoo Nubira Cars & Trucks

1 Answer

What is the procedure on removing an alternator from a 2001 Taurus with a duratec engine?


Okay, on your engine, the alternator is mounted below the rear cylinder bank of the engine, at the rear of the engine compartment. It'll be easier to access it from the driver's side front fenderwell (take off the right front tire then the plastic lining) or under the car. You might want to go ahead and remove both the liner and work from underneath as you'll need to remove your crankshaft pulley.

1: Disconnect the negative batery cable.

2: Disconnect the electrical connections from the alternator. The output wire is secured by a nut on the output terminal.

3: Revove the serpentine/drive belt.

4: Remove two bolts and one stud bolt that secure the alternator to it's bracket. Remove the crankshaft pulley.

Installation is reverse of removal.

After installing the alternator, reinstall the drivebelt and reconnect the negative battery cable.

To remove the crank-shaft pulley

1: As you'll aready have the wheel, liner, negative battery cable, and serpentine/drivebelt removed, as well as the car on jackstands, I'll omit those steps.

2: Remove the driveplate access cover and hold the ring gear teeth with a large scredriver or pry bar to prevent the crankshaft from turning.

3: Remove the nuts that secure the pullley bracket to the engine front cover. Remove the pulley and bracket.

4: The crankshaft pulley screws into the harmonic balancer with a left hand thread (reverse threaded so rightly loosey lefty tighty). Trun the crankshaft pulley clockwise to loosen and remove it.

5: Hopefully this is where you'll end with the pulley. The harmonic balancer is no fun to remove, but let me know if you need to know this too. After you have your alternator installed, put the pulley back onto the harmonic balancer before installing the serpentine/ drive belt.

Hope this info helps.

Jun 26, 2009 | 1999 Ford Taurus

1 Answer

I CANT LOCATE CRANK POSITION SENSOR


7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer

Apr 12, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
2002 Chevrolet Monte Carlo Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...