Question about 1994 Subaru Legacy Outdoor

2 Answers

Where is the hazard warning flasher

We have a 94 Sabaru legacy, need to know where the Hazard warning flasher unit is located. Or does it have one? The flashers won't shut off. I had to disconnect the turn signal relay. So we are using hand signals to make turns...a bit cold this time of year, but better than not being able to drive. One suggestion was to replace the blinker cam. The whole turn signal assy. is about $384...yikes! Any suggestions would be greatly appreciated.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Hi there, this can be caused from a few different things , Most likely the button on top of your steering column /behind your steering wheel on top has muck inside of it and needs to be cleaned inside out , second if you have recently replaced battery and or you don't have key remote for car that can be an issue for disabling immobilizer and will cause hazards to flash , the *warning flasher unit* is located left hand side behind glove box and is no easy task however i would think unlikely the problem, hope this helps :-)

Posted on Mar 20, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 361 Answers

It should be under the dash near the steering and brake pedal area, turn them back on and listen for it it is up on the left side it is about a 1 sq inch block type looks just like a relay that is under the hood in the fuse realy box

Posted on Mar 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emergency flasher switch


The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

Nov 26, 2015 | 2010 Chrysler Town and Country

1 Answer

How do i change a turn signal relay on a 2000 Chrysler Concorde


The Combination Flasher, also referred to as the combo-flasher, is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in a rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification.
The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher). The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.

Ref: http://www.10w40.com/questions/auto-repair-questions/where-is-the-flasher-relay-on-a-2000-chrysler-concorde
Good Luck

Mar 03, 2015 | 2000 Chrysler Concorde

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

1994 Sabaru Legacy flasher won't shut off


You need to tear the old switch out and replace.
I know the part for the blinker is called a "blinker cam" but I'm not sure if the hazard switch is a part of that. (I think it's a separate part)

Mar 15, 2014 | Cars & Trucks

1 Answer

How to change flasher unit 0n 2002 Saturn L-series


WARNING The flasher unit for turn signals should not be switched with a flasher unit for the hazard lights. To check the filaments of all of the turn signal bulbs and the brake lights, turn on the hazard flashers and walk around the car.
A flasher can be located in the fuse panel, under the dash in the wiring loom, in a glove box, under the hood, or somewhere else.
f36-02.jpg A fuse panel. Most flashers are located under the dashboard on the driver's side. When working properly, a flasher is easy to locate because it makes a ticking sound. When it is not functioning, a service manual may be needed to help locate it. Lighting company catalogs generally have pages listing the location of flashers.
To replace a flasher:
  • A flasher features two or three prongs that plug into a socket.
  • Just pull the flasher out of the socket and replace it with a new one.

Aug 24, 2012 | 2002 Saturn L-Series

2 Answers

My turn signals won't come on at all?


check the fuse if good then turn on the hazard lights if they work then you probably need a turn signal flasher which is a separate flasher unit then the hazard one.it usually looks like the hazard one so with the hazards on and locate it then you will know what the signal flasher looks like and you will also know not to change the wrong flasher unit.the signal flasher is often located at or near the under dash fuse panel or somewhere in the dash you don`t say what type of car your talking about.

Dec 12, 2011 | Cars & Trucks

1 Answer

Cant find 4 way hazard module 94 seirra


To find the FLASHER on 1994 GMC Truck C1500 1/2ton Sub 2WD 5.7L TBI 8cyl. the Flasher is located: Front seating area, driver side, under dash, driver side of steering column, mounted in relay bracket

Application: Hazard flasher


Turn SIgnal flasher is one independent unit.


Hope helps-

Sep 16, 2010 | 1994 GMC Sierra

2 Answers

Where do i find the flasher for the indicator? the left light wont come on even thogh we bought a new bulb


Flashers and Relays REPLACEMENT Pickups The hazard warning flasher, on the pickup, is located to the left of the steering column, beneath the instrument panel, and is secured by a clamp and one screw. To remove it, simply unplug the electrical connector, loosen the screw, and slide the flasher out of the clamp. The turn signal flasher is located to the right of the steering column, beneath the instrument panel, and is secured in the same way as the hazard flasher. The turn the signal relay is located to the immediate right of the hazard flasher, and is secured by two screws. To remove it, unplug the electrical connector and remove the screws. MPV The relays and flashers are located under the dash, near the fusebox. Navajo Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel. The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel. prev.gif next.gif

Jul 15, 2010 | 1992 Mazda B-Series

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

Where is the turn signal flasher unit located on a 2001 Chrysler Concord


here is the location of the flasher The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher) The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.
The combo-flasher is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in an rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification

Nov 26, 2009 | 2001 Chrysler Concorde

Not finding what you are looking for?
1994 Subaru Legacy Outdoor Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...