Question about 2007 GMC Yukon Denali

Open Question

Code p0641 P0641 GMC Yukon Denali- 5 Volt Reference Voltage Incorrect

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: '04 GMC Yukon Denali Check Engine Light

Did u put in fuel shortly before the light came on? I own 2 service centers & the most common situation with "Check Engine" lights are because the fuel cap wasn't re-installed or not tightened. When you refuel make sure it "clicks" when putting back on. We don't charge for a "Code Reading" but a dealer will, don't go there. Go, like the others suggested. If it is the fuel cap & you re-install it correctly, the light will go off after a short drive. Good Luck. PS-Don't panic when the "Check Engine" light comes on unless it blinks, if that happens don't drive. PSS-RE: Murray's, Auto-Zone.......If it's a "Code" (the reader will give a #) the code book will tell you the problem. PSSS-Some1 please have Troy W's Mommy & Daddy take away his keyboard. Just because you can put together a "Lego" car doesn't make you a master mechanic. You only repeated what we said except you have a "Napoleon" complex against any1 plugging something in to a vehicle. It's the same as plugging in a light @ home. In conjunction with "kinder" nine out of ten time in my experience it usually is the oxygen sensor(s) which would be about right with the year model

Posted on May 18, 2008

Ad
  • 1 Answer

SOURCE: location of fuse box/panel for 2004 yukon denali xl

There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Posted on Oct 20, 2008

  • 94 Answers

SOURCE: 2005 gmc yukon xl denali service ride control

it has to do with your air ride suspension best bet is take it to the dealer there is probably a problem with a level sensor. hope this helps you

Posted on Mar 16, 2009

  • 102 Answers

SOURCE: Need color codes for radio in 2002 gmc yukon denali

2002 GMC Yukon Car Stereo Wiring Guide
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Brown
Car Stereo Dimmer Wire: Gray
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Posted on May 24, 2009

  • 10 Answers

SOURCE: Heated seats won't stay on in 2004 GMC Yukon Denali

See GM TSB 05-08-143-001, If you have Adjustable pedals, especially if they don't work with the memeory buttons, but function with thier own buttons. Its the Brake Pedal Position Sensor is shorted and mesing up the seat module which controls the heaters too. My 05 Suburban had the same issue

Posted on Dec 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a 2008 GMC Envoy Denali, 2WD. Yesterday the engine would barely idle and numerous lights on the dash came on including the check engine light. I had a friend check the diagnostic codes and it came up...


Five days prior to this, the battery had to be replaced. The engine was started without the pause for two minutes ?????? Where do you people come up with some of this stuff ? Pausing for two min. before starting has nothing to do with it . DTC P0651: 5-Volt Reference 2 Circuit
Some of the engine sensors on your vehicle work off of a steady 5 volt supply by the PCM - engine computer . One of these sensors is short internally bring down the PCM .
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Accelerator Pedal Position (APP) Sensor 1 5-Volt Reference 2 Circuit
P0651
P2122
P0651
--
Accelerator Pedal Position (APP) Sensor 2 5-Volt Reference 1 Circuit
P0641
P2127
P0641
--
Air Conditioning (A/C) Refrigerant Pressure Sensor 5-Volt Reference 1 Circuit
P0641
P0532
P0641
--
Camshaft Position (CMP) Sensor 5-Volt Reference 1 Circuit
P0641
P0340
P0641
--
Engine Oil Pressure (EOP) Sensor 5-Volt Reference 1 Circuit
P0641
P0522
P0641
--
Fuel Tank Pressure (FTP) Sensor 5-Volt Reference 1 Circuit
P0641
P0452
P0641
--
Manifold Absolute Pressure (MAP) Sensor 5-Volt Reference 1 Circuit
P0641
P0107
P0641
--
The Crankshaft Position (CKP) Sensor 5-Volt Reference 2 Circuit
P0651
P0335
P0651
--
Throttle Position (TP) Sensor 1 and 2 5-Volt Reference 2 Circuit
P0651
P0122, P0222
P0651

That's why it wasn't running good ,an lights lit on the dash. Your best bet , take it to GMC dealer .
No where in GM service info does it say after replacing the battery that you need to wait two min. before starting .
Position the positive battery cable (1) to the battery.
Tighten the positive battery cable bolt.
Tighten
Tighten the bolt to 15 N·m (11 lb ft).
Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

Aug 02, 2017 | GMC Cars & Trucks

1 Answer

2007 cobaltpo651 circuit b how do i trll which is circuit b


DTC P0651: 5-Volt Reference 2 Circuit First off do you know what computer reference voltage is ? Your vehicle has 2 reference voltage circuits . This reference voltage is used to power engine sensors .
Diagnostic Fault Information
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Accelerator Pedal Position (APP) Sensor 1 5-Volt Reference 2 Circuit
P0651
P2122
P0651
--
Accelerator Pedal Position (APP) Sensor 2 5-Volt Reference 1 Circuit
P0641
P2127
P0641
--
Air Conditioning (A/C) Refrigerant Pressure Sensor 5-Volt Reference 1 Circuit
P0641
P0532
P0641
--
Crankshaft Position Sensor 5-Volt Reference 2 Circuit
P0651
P0335
P0651
--
Fuel Tank Pressure (FTP) Sensor 5-Volt Reference 1 Circuit
P0641
P0452
P0641
--
Intake Camshaft Position Sensor 5-Volt Reference 1 Circuit
P0641
P0340
P0641
--
Manifold Absolute Pressure (MAP) Sensor 5-Volt Reference 1 Circuit
P0641
P0107
P0641
--
Secondary Air Injection (AIR) Solenoid 5-Volt Reference 2 Circuit
P0651, P2432
P2431
P0651, P2431
--
Throttle Position (TP) Sensor 1 5-Volt Reference 2 Circuit
P0651
P0122
P0651
--
Throttle Position (TP) Sensor 2 5-Volt Reference 2 Circuit
P0651
P0222
P0651
--

How to check the 5v reference circuit for short to ground Cadillac

Jun 10, 2017 | Cars & Trucks

1 Answer

Code P0641 what does code mean


What make , model an year ? Could make a difference ! P0641 Sensor Reference Voltage Circuit Open

Mar 16, 2015 | Cars & Trucks

1 Answer

What is p0641 code on 05 impala


DTC P0641 The powertrain control module (PCM) provides a 5-volt reference to the following sensors:

The throttle position (TP) sensor 1
The accelerator pedal position (APP) sensor 2
The engine cooling fan speed sensor
The AC pressure sensor
The fuel tank pressure (FTP) sensor
The oil pressure sensor (OPS)
The PCM monitors voltage on the 5-volt reference circuit. If the voltage is higher or lower than required, DTC P0641 will set.

Aug 26, 2014 | 2002 Chevrolet Impala

1 Answer

Chevy cobalt 2010 scan code po641 reduce engine power


Possible causes
- Faulty Engine Control Module (ECM)
- ECM harness is open or shorted
- ECM circuit poor electrical connection
- Shorted sensor on 5 volt circuit
help.jpg What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected the sensor 5 volt reference circuit voltage is higher or lower than expected
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0641 Chevrolet Description
The control module has 2 internal 5-volt reference buses called "5-volt reference 1" and"5-volt reference 2". Each reference bus provided 5-volt reference circuit for more than one sensor. Therefore, a fault condition on one 5-volt reference circuit will affect the other 5-volt reference circuits connected to the reference bus. The control module monitors the voltage on the 5-volt reference buses.

Read more: http://engine-codes.com/p0641_chevrolet.html#ixzz31AP60YfR

Apr 19, 2014 | 2010 Chevrolet Cobalt

1 Answer

Po641 reduced engine power 07 silverado


P0641 Chevrolet Description
The control module has 2 internal 5-volt reference buses called 5-volt reference 1 and 5-volt reference 2 . Each reference bus provided 5-volt reference circuit for more than one sensor. Therefore, a fault condition on one 5-volt reference circuit will affect the other 5-volt reference circuits connected to the reference bus. The control module monitors the voltage on the 5-volt reference buses.


Read more: http://engine-codes.com/p0641_chevrolet.html#ixzz3Kg3EaTQP

Feb 21, 2014 | 2007 Chevrolet Tahoe

1 Answer

Buick problems


code p0641 refers to sensor reference voltage A--circuit malfunction===causes---wiring short to positive.

Dec 28, 2013 | Cars & Trucks

1 Answer

Chevy colorado


Hi there:

DTC P0641 - 5-Volt Reference 1 Circuit

DTC P0651 - 5-Volt Reference 2 Circuit

Diagnostic Fault Information
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit/System Description
The engine control module (ECM) has 2 internal 5-volt reference busses called 5-volt reference 1 and 5-volt reference 2. Each reference bus provides 5-volt reference circuits for more than one sensor. Therefore, a fault condition on one 5-volt reference circuit will affect the other 5-volt reference circuits connected to that reference bus. The ECM monitors the voltage on the 5-volt reference busses.

The 5-volt reference 1 bus provides 5 volts to the following sensors:
* The manifold absolute pressure (MAP) sensor
* The fuel tank pressure (FTP) sensor
* The air conditioning (A/C) refrigerant pressure sensor
* The accelerator pedal position (APP) sensor 2
* The intake camshaft position (CMP) sensor

The 5-volt reference 2 bus provides 5 volts to the following sensors:
* The APP sensor 1
* The throttle position (TP) sensor 1 and 2
* The crankshaft position (CKP) sensor

Conditions for Running the DTC
* DTCs P0601, P0602, P0603, P0604, P0605, P0606, P0607, and P2610 are not set.
* The ignition is in Unlock, Accessory, Run, or Crank.
* The ignition voltage is more than 5.23 volts.
* DTCs P0641 and P0651 run continuously when the above conditions are met.

Conditions for Setting the DTC
The ECM detects a voltage out of tolerance condition on the 5-volt reference 1 or 2 bus for more than 0.5 second.

Action Taken When the DTC Sets
DTCs P0641 and P0651 are Type A DTCs.

Conditions for Clearing the MIL/DTC
DTCs P0641 and P0651 are Type A DTCs.

Diagnostic Aids
It may be possible to locate the fault by disconnecting one component at a time from the 5-volt reference circuit while viewing the 5-Volt Reference circuit parameter on the scan tool. The scan tool parameter would change from Fault to OK when the source of the fault is disconnected.

If all 5-volt reference components have been disconnected and a Fault is still indicated, the fault may exist in the wiring harness.

Circuit/System Verification
With the ignition ON and the engine OFF, observe the 5-volt Reference 1 and 2 parameters. The scan tool should display 4.3-4.7 volts for a normally operating system.

Circuit/System Testing
Important: Additional DTCs will set when disconnecting the components.

1. Ignition OFF, disconnect the harness connector of all appropriate sensors for the applicable DTC.

Important: A short to voltage on the signal circuit of certain components may cause this DTC to set.

2. Ignition ON, measure for 4.8-5.2 volts between one of the 5-volt reference circuits and ground.

* If the voltage is less than the specified value, test for a short to ground on all the 5-volt reference circuits. If all circuits test normal, replace the control module.
* If the voltage is greater than the specified value, test for a short to voltage on all the 5-volt reference circuits, or the signal circuit, for each component associated with the appropriate 5-volt reference circuit. If all circuits test normal, replace the control module.

3. Connect each component associated with the 5-volt reference circuit, one at a time, while monitoring the voltage. The voltage should not change more than 1 volt.

* If the voltage display changes more than the specified value when a component is connected, replace the component.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 12, 2012 | Chevrolet Colorado Cars & Trucks

1 Answer

I have a p0641 code on my chervrolet hhr


We cannot do electrical troubleshooting over the internet. If you have wiring diagrams and the proper equipment, find out what voltage you are getting instead of the 5 volt reference signal, and trace it back to its origin (usually the ECU). Then repair or replace components as required. If you do not feel qualified to do this, take it to a reputable mechanic to troubleshoot and correct it for you.

Jun 07, 2012 | 2006 Chevrolet HHR

1 Answer

2005 pontiac grand prix, code p0641 came on. What


DTC P0641 The powertrain control module (PCM) provides a 5-volt reference to the following sensors:

The throttle position (TP) sensor 1
The accelerator pedal position (APP) sensor 2
The engine cooling fan speed sensor
The AC pressure sensor
The fuel tank pressure (FTP) sensor
The oil pressure sensor (OPS)
The PCM monitors voltage on the 5-volt reference circuit. If the voltage is higher or lower than required, DTC P0641 will set.

Conditions for Setting the DTC
The PCM detects a voltage that is higher or lower than required on the 5-volt reference circuit. The above condition is present for 1 second. Action Taken When the DTC Sets The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.
Conditions for Clearing the MIL/DTC The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. A current DTC, Last Test Failed, clears when the diagnostic runs and passes. A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. Clear the MIL and the DTC with a scan tool.

Yes i can be dangerous, depending which issues mentioned above has triggered the code such as a faulty gas peddle position sensor. the code can also cause a reduced engine power to activate.

Thank you for using Fixya and best advice is to have the dealer address these issues. A tech 2 scanner would be needed to address the P0641 DTC code.

Mar 19, 2010 | 2005 Pontiac Grand Prix

Not finding what you are looking for?
2007 GMC Yukon Denali Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...