Question about Mercedes-Benz Sprinter

Open Question

HAVE FAULT CODE C1409

HAD CODE C1401 REPLACED ABS PUMP NOW HAVE CODEC1409

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CAMRY ABS FAULT CODES 35&21 HAVE REPLACED R/H/F SENSOR & ABS PUMP/MODULE, STILL THE SAME


code 21 is

Open or short circuit in 2?position solenoid circuit for left front wheel

pop possible causes ABS actuator/SFLR or SFLH circuit



Oct 11, 2016 | 2001 Toyota Camry

1 Answer

Abs replaced axle shaft @ abs cable abs light still on after reset


The ABS fault light will stay on until the problem is repaired, read the fault code and diagnose it again.

May 14, 2016 | 2003 Mazda Protege

1 Answer

2007 GMC Canyon ABS Fault - Originally ABS Fault started when making a sharp right turn. (ABS Fault light only). Stopping and restarting would clear 'fault' until next hard right. Later, occasional metal...


id check your caliper to see if the piston is compressing all the way if not check your fluid it should be clean not brown or if you have been through large amounts of water if it has gotten into the brake system and check your bleeder valve to check if it has rotted or come lose or if you have a break in the lines or air, most likely your caliper is failing to compress.

Nov 05, 2013 | 2007 GMC Canyon Crew

1 Answer

Mini abs pump motor power supply fault code 5E2D


Check and replace the ABS motor control relay.

Feb 19, 2013 | Mini Cooper Cars & Trucks

1 Answer

ABS Light Stays On


Since you replaced the pick up units or sensors, check the tone rings on the axle shafts. The tone rings is what the sensors detect and are located at each wheel that has ABS. A tone ring looks like this:

1_3_2013_9_47_55_pm.jpg
This tone ring is on a Ford Ranger - which is pretty much the same as your Mointaineer. Notice the break in the tone ring. This will cause an ABS Fault indicator and will need to be replaced to extinguish the lamp. Check the brake fluid level and top off if needed.


Try another AutoZone or similiar to get a code and be non-specific about the light - just say a light came on on the dash and you don't know what it is about.

Good luck!

Jan 03, 2013 | 2004 Mercury Mountaineer

1 Answer

AWD Disable light on 2001 Pontiac Aztec- how do I get if off?


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 11, 2012 | 2001 Pontiac Aztek

2 Answers

Check abs system lite on how do you find the code list


ABS Fault Code List 1991 Corvette (C4)
Code Definition
21 Right Front Wheel Speed Sensor Fault
22 Right Front Toothed Wheel Frequency Error
25 Left Front Wheel Speed Sensor Fault
26 Left Front Toothed Wheel Frequency Error
31 Right Rear Wheel Speed Sensor Fault
32 Right Rear Toothed Wheel Frequency Error
35 Left Rear Wheel Speed Sensor Fault
36 Left Rear Toothed Wheel Frequency Error
41 Right Front Solenoid Valve Fault
45 Left Front Solenoid Valve Fault
55 Rear Wheels Solenoid Valve Fault
61 Pump Motor or Motor Relay Fault
63 Solenoid Valve Relay Fault
71 Electronic Brake Control Module Fault
72 Serial Data Line Fault
75 Lateral Accelerometer Fault (Short ot Open)
76 Lateral Accelerometer Fault (Signal out of Range)

Mar 12, 2010 | 1991 Chevrolet Corvette

1 Answer

My grans hyundai getz 53 reg had an abs fault, i tried my bosch kts an snap~on solus but would not give any fault codes, i borowed a friends diag tool an it found an engine mgnt fault in abs system, i...


hi from uk for your info there was a recall back in2004/5 for the getz relating to the abs system going faulty my wifes 2003 getz gsi was recalled and i took car to dealers for her to enquire what fault has there beenon some getz with abs system? as fault had not occured on ours ? apparently there had been a fault with the wire loom to pump particularly the earh cable deteriating ? so this loom had to be inspected and replaced under warranty however as i had waxoiled all underneath our getz including abs pump due to its location low down the loom was ok but was changed anyway and recorded and a dated sticker placed on cars glove compartment door inside to verify loom changed ? SO b4 you progress any further i would check with hyundai tech dept to whether you car had been inspected or whether slipped through unchecked ? your gran should have had a recall as we did for modified loom hope this helps?

Dec 09, 2009 | 2003 Hyundai Santa Fe

1 Answer

XK8 ABS FAULT LIGHT COMES ON INTERMITANTLY PLUS TRACTION FAULT SHOWS


Number of possibilities. Most likely culprit is wheel bearings. Have these checked. Big heavy car and wheel bearings do take a hammering on XK and XJ's. Once they go, the wheel speed sensors are out of line with the tracking ring and a fault code is thrown. As the TCS uses the same sensor, this also throws a fault. Next in line is the ABS unit (it's hardly ever the main block, but ECU itself, companies on the net offer rebuilt units. Finally it can be the ABS pump unit - but the fault codes will show if this is the case - or you can pull the pump unit plug out of the ABS unit and see if it has continuity with a multimeter - should be a low number of ohms. 8 times out of 10, it is wheel bearing.

Jul 23, 2009 | 1998 Jaguar XK8

1 Answer

Abs system


hi need to get a fault code reading it will tell you where to look but a simple thing you can do is check the fuses for the abs pump usualy when the abs comes on its a wheel sensor but the quickest way to check is get the fault code reading yates210456

Oct 05, 2008 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...