Question about 2007 Ford Focus (3 Door) Hatchback

1 Answer

2007 Ford Focus front passenger side turn signal blinks fast. Works fine with head lamps off, doesn't work when headlamps are on.

2007 Ford Focus front passenger side turn signal blinks fast. A number of sources say this is due to a burned out bulb. I checked the bulbs, they appear to work fine when my headlamps are off. When I turn the headlamps on, the front passenger side turn signals do not light up at all.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 3,178 Answers

Faulty earth wire on the wiring cluster for the heat light check with a meter and fix the earthing point.

Posted on Mar 19, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: turn signal does not work

I found a wire pulled loose in the connector at the turn signal switch on the steering column.I believe it was blue and yellow,not too hard to get the covers off .2001 sport trac

Posted on Dec 02, 2008

  • 14 Answers

SOURCE: turn signal problems

Turn signals have a relay (its a small switch that charges and discharges current) which controls your turn signals blinking speed and interval. This is most likely your problem. You should be able to get a new one at your local parts store. Follow these instructions, in this order, and let me know how it works.

Step 1:Turn on the hazard lights and walk around the Taurus checking that all four turn signal lights are working. If any of them are not working, replace the bulbs. A non-working bulb in any of the turn signals will often make the turn signals appear that a flasher is going bad.

Step 2:
Locate the fuse box and check the fuses for the turn signals. There may be more than one. Replace any fuses that are blown and then recheck the turn signals again. If they still aren't working properly, then move on to replace the flasher. Step 3: Look for a round, silver-colored object near the fuse box. Put your finger on the object and turn on the turn signal. You should be able to feel a mechanical clicking as the turn signal blinks. This is the flasher. Step 4: Pull the silver flasher out of the socket and replace it with the new one. Each of the flashers should have two pins sticking out of the bottom side. Start the Taurus and recheck the turn signals to ensure that they work. Joel

Posted on Mar 04, 2009

  • 1779 Answers

SOURCE: 1998 ford taurus left turn signal blinking fast

Replace the bulb that stays on and doesn't blink, if that doesn't solve the problem, let me know.

Posted on Apr 13, 2009

pippall
  • 1486 Answers

SOURCE: 2006 Ford Ranger. Rear passenger side tail light

Bad earth connection.Clean or replce wire.

Posted on Jun 18, 2009

  • 14036 Answers

SOURCE: 97 ford escort left turn signal ticks fast, but no lighty outside

A BAD BULB MORE LIKELY.

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

1 Answer

Explorer 2007 Right Head Lamp And HighBeam Problem


Have you checked the bulbs? There are individual fuses for each headlamp so you'll want to check those also. they are in the battery junction box which is under the hood on the driver's side, fuse 29 is for the right headlamp and fuse 34 is for the left headlamp.

Jul 27, 2015 | 2007 Ford Explorer Eddie Bauer

1 Answer

03 chevy venture rt.front parking light&turn light don't work replace bulb&socket


The rapid flashing occurs because of the light problem. If the 20A PARK LP fuse in the underhood fuse block is OK, the front marker lamps and the park lights should turn on when you set the headlamp switch to PARK. If the 10A T/SIG fuse in the instrument panel fuse block is OK, and the ignition switch is on, moving the turn signal multi-function switch to signal a right or left turn should cause the turn signals to flash. If this doesn't happen, check for a missing ground connection to the socket you replaced and check to be sure the replacement lamp was not forced into the socket backwards (it happens).

Sep 17, 2012 | 2003 Chevrolet Venture Passanger

1 Answer

4runner flasher not working


the bulb has 2 fillaments and one is burnt out replace the bulb

Jul 26, 2012 | 2007 Toyota 4Runner

2 Answers

2002 Pontiac Montana. Front passenger side turn signal doesn't blink but the bulb is working as a running light. The faulty turn signal connection causes the right turn signal to blink excessively fast. Do...


Need to replace the bulb. There are 2 filaments in the bulb. 1 works parking light the other is turn signal. It flashes fast to alert you that it has a blown out bulb.

Jun 25, 2010 | 2002 Pontiac Montana

1 Answer

I have a 2005 G6, the front drivers side turn signal lamp is not working. The drivers rear blinks twice as fast. I have replaced the bulb, I switch the bulb and headlight assembly from the driver to the...


fast flashing on the one bulb is a fault is due to the failure of one bulb, hence the holder for the flasher unit not wirking has gone defective the contact may have broke in the flasher unit not working , look in where the bulb goes and compare the working and non working unit, you may see a contact missing, hence repace unit, or repair

Dec 22, 2009 | 2005 Pontiac G6

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

2002 Hyundai elantra driver side turn signal not working outside


This simply means that the front driver side turn signal bulb has failed. Replace it.

Oct 28, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
2007 Ford Focus (3 Door) Hatchback Logo

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...