Question about Cars & Trucks

Open Question

Trying to locate Map Sensor for 57 Vortec truck won't run got code P0108 can u help?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 1998 chevy suburban map sensor

Hi, The Map sensor on a Suburban is located.
Beside of the ignition coil. on the intake.
Is a litle sensor with a connector of 3 wires.

I hope this work for you. OK

Posted on Jul 03, 2008

  • 383 Answers

SOURCE: 1999 Nissan Altima MAP sensor location

The MAP sensor is located on the driver's side of the engine compartment next to the air filter housing and shock tower.
It is a small plastic component with one vacuum hose coming off of it and an electrical connector that has two wires. It might be advantageous to write in and let me and/or other techs know what the symptoms are prior to replacing the sensor. Sometimes just replacing the part is a waste of money. The fact that the code has indicated the problem is the MAP sensor, doesn't mean it is bad. As an example, check to see if the Vacuum hose is secure and not disconnected or split at either end.
Good luck.

Posted on Apr 05, 2009

  • 14036 Answers

SOURCE: 2002 intrepid vacuum issue p0108

CODE PO108 IS MAP SENSOR CIRCUIT HIGH INPUT.

Posted on Aug 01, 2009

  • 15 Answers

SOURCE: 2000 silverado 5.3 p0108 code wont run when i

po108 is map sensor try replaceing map sensor

Posted on Mar 22, 2010

  • 134 Answers

SOURCE: my 2004 toyota tacoma has

Yes your truck is equipped with a mass airflow sensor (MAF). However, I would not just replace that because its running rough. I would begin diagnostics by first checking to see if there were any trouble codes in the engine to give you a clue as to the rough running condition. I would expect a trouble code to be present to support the descision to replace the MAF Sensor. If no codes are present I would suggest that you get the vehicle tuned up. (Spark plug replacement and throttle body cleaning and I would also suggest removing the idle control valve and cleaning the carbon and dirt out of it. Although what you were told might be correct I dont belive that is where I would start.

Posted on Feb 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got p0748 p0108 code on my 04 honda odyssey. Car sat for about one year. Replaced fuel pump yesterday and it started right up. Can I get info on locations of where sensors are?


PO 748
service the transmission .....check solenoids

- Dirty transmission fluid - Low transmission fluid level - Faulty line pressure solenoid valve 'A' - Line pressure solenoid valve 'A' harness is open or shorted - Line pressure solenoid valve 'A' circuit poor electrical connection

Read more: http://www.autocodes.com/p0748.html

P0108
is the code for a problem with the MAP electrical circuit sensor having too high voltage input to the Engine Control Unit (ECU). This means that the voltage input to the ECU is too high and that it is not in the correct range for proper engine operation to work with inputs from the Mass Air Flow Sensor (MAF) and Throttle Position Switch (TPS). P0108 OBD II Trouble Code Manifold Air Pressure MAP Barometric Pressure...


odyssey map sensor is on the throttle body

Map sensor


26349763-lyuervfxp0xfzshzuykucxk0-2-0.jpg

Nov 10, 2016 | Honda Cars & Trucks

1 Answer

Code p1296,p0108,p1494,p0500 on 2000 durango, what most likely wrong?


P1296 No 5-Volts to MAP Sensor
P0108 MAP Sensor Voltage Too High
P0500 No Vehicle Speed Signal Circuit
P1494 Leak Detection Pump Switch or Mechanical Faul
I would try MAP sensor first.

Mar 18, 2014 | Dodge Durango Cars & Trucks

1 Answer

Get codes p0068 and p0108


codes p0068 refer to Manifold pressure sensor/mass air flow sensor--throttle position correlation--causes ---wiring---map sensor---maf sensor--mechanical fault.
code p0108 refers to manifold absolute pressure(map) sensor/barometric pressure (BARO) sensor--high input. causes ---wiring short to positive---map sensor---baro sensor---ecm.

Mar 28, 2013 | 2002 Dodge Intrepid

1 Answer

Car starts and dies, code is p0108


A p0108 trouble code is a MAP sensor error code. To be more specific your sensor has to high a voltage. You may want to try replacing your your MAP sensor. Just be sure to disconnect your negative battery cable before you replace the sensor. If you do not do this you may short out the new sensor. I hope this helps you out.

Sep 17, 2011 | 2001 Mazda MPV

1 Answer

What are these codes that appears on my engine check machines? p1391,p1297,p0108,p1492


P1391 Intermitant loss of cam or crank; P1297 No change in map from start to run; P0108 Map sensor voltage too high; p1492 Battery temp sensor too high.

Apr 16, 2011 | 2002 Chrysler Sebring

1 Answer

What is a p0108 sensor? and my radiator fan runs all the time and the temp gauge don't work now how do i fix it


Although it sounds more like the problem has to do with your coolant temperature sensor, your P0108 means there is a problem with the MAP sensor.

Anyway, check out http://www.obd-codes.com/p0108 for details.

Oct 26, 2010 | 2000 Dodge Neon

1 Answer

2000 silverado 5.3 p0108 code wont run when i


po108 is map sensor try replaceing map sensor

Mar 21, 2010 | 1999 Chevrolet K1500

1 Answer

Po108 and po172


P0108: MAP sensor circuit high input
P0172: System too rich (bank 1)
Possible repair for '108', replace the Map sensor. Clear codes and run car. If ok, the MAP sensor may have caused the '172' error. Hope this helps.

Nov 15, 2009 | 1997 Plymouth Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...