Question about 2005 Buick Century

1 Answer

Remote not work cannot key open door

Need one remote to open doors

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 139 Answers

Check the fuses or your remote battery went dead try replacing it. or your remote bacame deprogrammed and you`ll need to go to 1he dealer and have it reprogrammed. Usually $50 to $80

Posted on Apr 07, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 57 Answers

SOURCE: remote car key not working to unlock car. it does

Most likely the remote is the culprit.It sending a signal and the body control module is receiving it so that eliminates the remainder of the system.If you have two remotes then try the other one.If not, you can go to your nearest dealership and they have a remote checker.They can set the remote on it and push the buttons and it will light up if all the buttons are working on your remote.Hope this information helps,
Ken

Posted on Oct 08, 2010

  • 39 Answers

SOURCE: keyless remote works intermittently

replace the battery in your remote, or have it checked at autozone to make sure it's not just your remote.

Posted on Feb 06, 2009

Audioaholic
  • 376 Answers

SOURCE: door/trunk won't open with remote

I dont know what buick you have, but here is a site that should help you out, remotes can be programed for several different options, such as turning on/off the interior light when unlocked, or keeping the headlights on/off when locked. on the site listed below, follow links to your speciffic make, and it will list the directions for programming.

http://www.programyourremote.com/classified/BrowseMake.asp?cid=48

Posted on Jan 28, 2011

  • 14036 Answers

SOURCE: we have 2 remote key

TO SYNCHRONIZATION REMOTES WHEN REPLACING BATTERIES,STAND 5 FEET OF THE VECHICLE.PRESS REMOTE TRANSMITTER LOCK AND UNLOCK BUTTONS SIMULTANEOUSLY FOR 7 SECONDS.HORN SHOULD CHIRP TO CONFIRM SYNCHRONIZATION.

Posted on May 18, 2011

  • 5252 Answers

SOURCE: it rained in my car and now my trunk release does

Sounds like water got to that trunk release. Pull it out, try drying it off, or replacing it if it looks damaged. maybe water is still collected at the electrical connector, or has corroded it.

Posted on Oct 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a Holden Astra TS city 98 model car and the remote on the key will open all the doors except the drivers door, so to lock all doors I have to put the key in the drivers door or use the remote &...


A plastic clip that holds the lock linkage is probably broke or worn. You need to pull of the inner door panel to see whats going on inside. Use the remote and see whats happening. It could be bent rod in door from someone using a slim jim to unlock it when they locked the keys in it at some point. Bend the rod and try the remote again untill it works properly.

Aug 31, 2014 | Cars & Trucks

1 Answer

Remote key fob won'tprogram


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 13, 2009 | 1999 Ford Escort

1 Answer

The remote to unlock the doors won't work. replaced battery. the key will not unlock driver or passenger door or the trunk


I hope you're able to get into your car because it sounds like the system needs to be reprogrammed.

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 11, 2009 | 2005 Toyota Corolla

1 Answer

Had car in shop for some body repair. Now remote key will not disarm alarm or unlock doors


It sounds like they disconnected your battery when they worked on your car....
Try this and see if it works..


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 10, 2009 | 2003 Jaguar S-Type

1 Answer

How do i program a remote control for a 1998 toyota vienta


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 04, 2009 | 1998 Toyota Camry

1 Answer

Remote works but doors don't lock/unlock


Check the remote battery or replace. Check all fuses. If you need to reprogram, try this.

key not in ignition.
driver door open-others closed
driver door unlocked

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice
this is rewrite mode,have all remotes to reprogram
it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possesion,you are done.

to end mode open door or insert key into ig.you can do up to 4 remotes.read this a couple of times to get the sequence down.there are time restraints,but if you go in order it will work.do not wait more than a second b/t each step and you will be ok.i know from experience that you can do this as fast as you can and it will enter mode.if steps out of order or you wait to long it wont.print this and have in lap,read ahead of what you are doing.good luck

Jun 13, 2009 | 2000 Toyota Land Cruiser

1 Answer

Automatic door locks will not work.


you need to take it to the dealer and have them check the bcm for codes.... also have them check to be sure you have the latest software in the bcm.. its possible that you just need a software update... there are several TSB's covering the concern you have..... it can be a very simple fix with software or even a stuck lock switch may need to be replaced... without the proper diagnostic codes being read from the bcm all that can be done is guessing..and that can be expensive...

Feb 02, 2009 | 2005 Chrysler Town & Country

3 Answers

Program remote control for mazda mpv 2002


Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Dec 06, 2008 | 2000 Mazda MPV

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

2 Answers

Keyless entry remote


Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
2005 Buick Century Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...