Question about Jeep Grand Cherokee

1 Answer

New flasher relay good fuse no four way flasher no turn signals

First I tried soldering the flasher relay. that did not work. I checked fuses, they were goon (no.4 fuse) on panel.I replaced flasher relay. now I have no flasher or turn signals. Are there other fuses I could be looking for?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 3,204 Answers

You need to check the bulbs holders and wiring even a blown bulb will not blow the fuse and an damaged wire or bulb holder will as it will make earth and live go together. there are also fuses for left side and right side turning lights cannot remember rating think they are 10amp.

Posted on Mar 19, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: no flashers or turn signals

Try the fuse/breaker panel under hood, drivers side.

Posted on Jun 26, 2008

thutson66
  • 96 Answers

SOURCE: turn signals and hazard flashers quit working

There are two possible locations for the relay.

First in the fuse panel, close to the bottom.

Second, in some models they put the darn thing behind the dash in the center of the car, it's a real pain to get to if it's that one.

Good luck

Posted on Aug 05, 2008

  • 566 Answers

SOURCE: turning signal and 4-way hazard flasher not working

the actual hazard lights switch is also a relay and linked to signals left/right try checking this out ?

Posted on Nov 27, 2008

  • 1986 Answers

SOURCE: Brake/turn signals/flashers not working, fuses ok, what now?

There should also be a unit called the electronic flash module / unit. It should be somewhere under the driver's side dash.. unfortunately I do not know where in particular

Posted on Aug 13, 2009

  • 1168 Answers

SOURCE: Turn signals not working.All bulbs are good,no

The emergency flasher and the turn signal flasher are two separate items. You could have a defective T/S flasher.

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals don't work but my four ways do


Four way flashers and turn signals are two different flasher relays. If all fuses are good, then check your owners manual for the location of the turn signal relay and replace it.

Sep 15, 2014 | Cars & Trucks

3 Answers

Turn signals work inconsistently. fuse and bulbs fine, same with hazards


Try replacing your turn signal flasher if all bulbs and fuses are good.

Jul 02, 2014 | 1998 Chevrolet S-10 Pickup

2 Answers

Where is the fan relay located on a 98 Chevrolet camaro?


there are three of them(assuming coolant fan) and they are located in the under hood electrical center. Left(dr) front corner of engine compartment.

Nov 18, 2011 | 1998 Chevrolet Camaro

1 Answer

1998 taurus - turn signals were working - pushed the hazard lights button - hazards did not work and also now turn signals do not work


Check the fuse/relay panel for a blown fuse/relay. Also look at the turn signal flasher and the four way flasher located in fuse/relay panel for problem. If the fuses are good replace the flashers to correct the problem. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

New bulbs, turning signals do not work...


Check the flasher located in the fuse/relay panel. Also check for a blown fuse as well. Remember this if the 4 way flashers are not working the turn signals will not either. To test the flasher before you remove it, turn the turn signal switch to either side and with your finger touch the top of flasher. If you feel a click from flasher then it's good and you will have another problem in the wiring. Hope this will help you.

May 15, 2010 | Cars & Trucks

2 Answers

No turn signals but flashers work


There a two modules 1 for the turn signals and 1 for the flashers. Look under your dash around the steering wheel and fuse box area for one that is in the wiring harness.

May 31, 2009 | 1991 Ford Ranger Supercab

1 Answer

New relay installed fuses checked but only four way flashers working but no left or right turn signals work . is there more than one fuse in another location? this is a 1997 E superduty ford van


try turning the four ways on and off several times tap on the four way switch these switches go bad and keep the turn signals or fourways from coming on

Mar 28, 2009 | Ford E-Series Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...